Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on the "Bus Check" screen.

·

"Skid Control ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside of brake actuator assembly (skid control ECU)

·

Brake actuator assembly (skid control ECU) CAN branch wire or connector

·

Brake actuator assembly (skid control ECU)



WIRING DIAGRAM

C290659E01
1.644,3.314 2.852,3.454 1.208,0.140 10 from IG No.1 Relay 0.399,1.74 2.072,1.962 1.673,0.223 10 No. 1 Junction Connector 5.211,4.777 5.520,4.988 0.309,0.211 10 A17 5.61,1.257 6.127,1.395 0.517,0.138 10 CANL 5.61,0.675 6.127,0.813 0.517,0.138 10 CANH 5.336,0.575 5.520,0.719 0.184,0.144 10 12 5.61,3.311 6.127,3.449 0.517,0.138 10 IG1 5.42,3.225 5.521,3.368 0.101,0.144 10 8 5.61,3.895 6.127,4.033 0.517,0.138 10 GND1 5.341,3.809 5.520,3.952 0.179,0.144 10 16 5.61,2.134 6.127,2.272 0.517,0.138 10 +BM 5.42,2.034 5.521,2.178 0.101,0.144 10 1 5.61,2.73 6.127,2.868 0.517,0.138 10 +BS 5.34,2.629 5.520,2.773 0.179,0.144 10 32 5.338,1.153 5.520,1.293 0.182,0.140 10 13 1.66,0.575 1.863,0.719 0.203,0.144 10 8 1.66,1.153 1.842,1.293 0.182,0.140 10 19 4.106,1.982 4.485,2.119 0.379,0.137 10 ABS1 4.106,2.56 4.485,2.697 0.379,0.137 10 ABS2 2.067,2.116 2.856,2.276 0.788,0.160 10 from Battery 2.067,2.718 2.856,2.879 0.788,0.160 10 from Battery 3.875,3.173 4.713,3.314 0.838,0.141 10 ECU-IG No.1 5.211,4.933 6.802,5.256 1.591,0.323 10 Brake Actuator Assembly (Skid Control ECU) 0.403,1.58 0.773,1.780 0.370,0.200 10 J75

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
U152527E01
1.246,1.152 1.073,0.726 1.073,0.726 0.961,0.726 false 1.342,1.161 1.093,1.858 1.093,1.858 0.961,1.858 false 0.08,0.054 0.252,0.214 0.172,0.159 10 *a 1.568,0.576 1.836,0.713 0.268,0.137 10 A17 0.432,1.788 0.865,1.925 0.433,0.137 10 CANH 0.478,0.648 0.874,0.785 0.395,0.137 10 CANL

Disconnect the A17 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A17-12 (CANH) - A17-13 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SKID CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U152528E01
2.617,1.137 2.73,0.7 2.73,0.7 2.841,0.7 false 0.756,1.137 0.643,0.7 0.643,0.7 0.531,0.7 false 1.726,1.185 1.464,1.858 1.464,1.858 1.333,1.858 false 0.08,0.054 0.252,0.214 0.172,0.159 10 *a 1.561,0.61 1.829,0.748 0.268,0.137 10 A17 0.044,0.615 0.476,0.753 0.433,0.137 10 GND1 1.056,1.773 1.452,1.911 0.395,0.137 10 IG1 2.858,0.622 3.179,0.759 0.321,0.137 10 +BM 2.612,1.47 2.77,1.862 2.77,1.862 2.881,1.862 false 2.917,1.777 3.238,1.914 0.321,0.137 10 +BS

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-16 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A17-1 (+BM) - Body ground Always 11 to 14 V
A17-32 (+BS) - Body ground Always 11 to 14 V
A17-8 (IG1) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR