Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on the "Bus Check" screen.

·

"ECM Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside ECM

·

ECM



WIRING DIAGRAM

C289527E02
5.19,0.659 5.454,0.797 0.265,0.137 10 A24 2.17,0.659 2.952,0.797 0.782,0.137 10 from Battery 1.999,1.178 2.951,1.315 0.952,0.137 10 from EFI Relay 2.16,2.231 2.952,2.368 0.792,0.137 10 to EFI Relay 1.999,2.765 2.951,2.902 0.952,0.137 10 from IG2 Relay 3.959,0.514 4.557,0.651 0.598,0.137 10 EFI NO.1 4.126,2.62 4.394,2.757 0.268,0.137 10 IGN 5.275,0.44 5.371,0.577 0.096,0.137 10 1 5.626,0.659 6.111,0.797 0.485,0.137 10 BATT 5.19,1.185 5.454,1.322 0.265,0.137 10 A24 5.275,0.965 5.371,1.102 0.096,0.137 10 2 5.626,1.185 6.111,1.322 0.485,0.137 10 +B2 5.19,1.712 5.454,1.850 0.265,0.137 10 A24 5.275,1.493 5.371,1.630 0.096,0.137 10 3 5.626,1.712 6.111,1.850 0.485,0.137 10 +B 5.19,1.712 5.454,1.850 0.265,0.137 10 A24 5.275,1.493 5.371,1.630 0.096,0.137 10 3 5.626,1.712 6.111,1.850 0.485,0.137 10 +B 5.19,2.764 5.454,2.901 0.265,0.137 10 A24 5.236,2.544 5.408,2.681 0.172,0.137 10 28 5.626,2.764 6.111,2.901 0.485,0.137 10 IGSW 5.19,2.24 5.454,2.378 0.265,0.137 10 A24 5.236,2.021 5.408,2.158 0.172,0.137 10 34 5.626,2.24 6.111,2.378 0.485,0.137 10 MREL 5.183,4.77 5.461,4.907 0.279,0.137 10 D74 5.236,4.551 5.408,4.688 0.172,0.137 10 43 5.637,4.77 6.121,4.907 0.485,0.137 10 E01 5.868,5.397 6.353,5.535 0.485,0.137 10 ECM 5.187,4.318 5.465,4.455 0.279,0.137 10 D74 5.24,4.099 5.413,4.236 0.172,0.137 10 82 5.641,4.318 6.126,4.455 0.485,0.137 10 ME01 5.187,3.821 5.465,3.958 0.279,0.137 10 D74 5.24,3.601 5.413,3.739 0.172,0.137 10 81 5.641,3.821 6.126,3.958 0.485,0.137 10 E1 5.187,3.292 5.465,3.429 0.279,0.137 10 D74 5.24,3.072 5.413,3.210 0.172,0.137 10 42 5.641,3.292 6.126,3.429 0.485,0.137 10 E02

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

Disconnect the A24 and D74 ECM connectors.

U152462E01
6.555,1.44 6.836,1.582 0.281,0.142 10 D74 0.576,1.44 0.843,1.582 0.267,0.142 10 A24 0.099,0.078 0.364,0.220 0.265,0.142 10 *a 1.498,0.822 1.564,0.822 1.564,0.822 1.884,1.199 false 1.564,0.339 1.769,0.481 0.205,0.142 10 +B 2.966,0.775 3.471,0.917 0.505,0.142 10 IGSW 2.939,0.842 2.872,0.842 2.872,0.842 2.604,1.376 false 1.641,0.655 1.707,0.655 1.707,0.655 1.975,1.189 false 1.769,0.406 1.835,0.406 1.835,0.406 2.064,1.189 false 1.363,0.58 1.641,0.722 0.279,0.142 10 +B2 1.131,0.76 1.509,0.902 0.378,0.142 10 BATT 5.322,1.686 5.461,2.18 5.461,2.18 5.545,2.18 false 4.984,2.183 5.061,2.183 5.061,2.183 5.229,1.682 false 5.417,1.348 5.207,0.536 5.207,0.536 5.118,0.536 false 4.951,0.765 5.019,0.765 5.019,0.765 5.32,1.348 false 4.792,2.123 4.980,2.265 0.188,0.142 10 E1 5.556,2.123 5.945,2.265 0.389,0.142 10 ME01 4.689,0.707 4.954,0.849 0.264,0.142 10 E02 4.857,0.461 5.242,0.603 0.386,0.142 10 E01 1.379,2.169 1.884,2.311 0.505,0.142 10 MREL 1.8,2.235 1.908,2.235 1.908,2.235 2.19,1.646 false

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D74-42 (E02) - Body ground Always Below 1 Ω
D74-43 (E01) - Body ground Always Below 1 Ω
D74-81 (E1) - Body ground Always Below 1 Ω
D74-82 (ME01) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-1 (BATT) - Body ground Always 11 to 14 V
A24-2 (+B2) - Body ground Battery positive (+) voltage applied to terminal A24-34 (MREL) 11 to 14 V
A24-3 (+B) - Body ground Battery positive (+) voltage applied to terminal A24-34 (MREL) 11 to 14 V
A24-28 (IGSW) - Body ground Ignition switch ON 11 to 14 V


Result
Result Proceed to
OK (for 1UR-FE) A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C
NG D



A

B

C

D

REPAIR OR REPLACE HARNESS OR CONNECTOR