Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"Airbag" is not displayed on the "Bus Check" screen.

·

"Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or center airbag sensor assembly

·

Center airbag sensor assembly CAN branch wire or connector

·

Center airbag sensor assembly



WIRING DIAGRAM

C279373E20
5.417,3.938 5.781,4.083 0.365,0.146 10 false J46 5.417,4.104 6.75,4.469 1.333,0.365 10 false Center Airbag Sensor Assembly 5.583,3.313 6.948,3.688 1.365,0.375 10 false E2 5.583,2.708 6.948,3.083 1.365,0.375 10 false E1 5.583,2.125 6.948,2.5 1.365,0.375 10 false IG2 5.583,0.677 6.948,1.052 1.365,0.375 10 false CANH 5.583,1.271 6.948,1.646 1.365,0.375 10 false CANL 5.313,2 6.677,2.375 1.365,0.375 10 false 21 5.302,2.625 6.667,3 1.365,0.375 10 false 25 5.302,3.208 6.667,3.583 1.365,0.375 10 false 26 5.333,1.146 6.698,1.521 1.365,0.375 10 false 22 5.333,0.583 6.698,0.958 1.365,0.375 10 false 13 1.635,0.583 1.771,0.75 0.135,0.167 10 false 3 1.635,1.125 1.844,1.302 0.208,0.177 10 false 14 0.417,1.625 0.688,1.781 0.271,0.156 10 false J75 0.417,1.792 2.667,2 2.25,0.208 10 false No. 1 CAN Junction Connector 2.469,2.125 3.469,2.417 1,0.292 10 false from IG2 Relay 4.375,1.979 4.656,2.125 0.281,0.146 10 false IGN

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U152453E02
2.01,1 2.479,0.417 2.479,0.417 2.563,0.417 false 2.135,1.25 2.49,1.656 2.49,1.656 2.573,1.656 false 0.427,1.01 0.677,1.156 0.25,0.146 10 false J46 2.615,0.333 3.052,0.51 0.438,0.177 10 false CANH 0.063,0 0.271,0.177 0.208,0.177 10 false *a 2.594,1.583 3,1.76 0.406,0.177 10 false CANL

Disconnect the J46 center airbag sensor assembly connector.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J46-13 (CANH) - J46-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
U152454E02
2.26,1.198 2.438,1 2.438,1 2.531,1 false 1.792,1.271 2.146,1.667 2.146,1.667 2.24,1.667 false 1.667,1.271 1.979,1.917 1.979,1.917 2.063,1.917 false 0.427,1.01 0.667,1.156 0.24,0.146 10 false J46 2.563,0.927 3,1.104 0.438,0.177 10 false IG2 0.063,0 0.271,0.177 0.208,0.177 10 false *a 2.25,1.594 2.656,1.771 0.406,0.177 10 false E1 2.083,1.844 2.49,2.021 0.406,0.177 10 false E2

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J46-25 (E1) - Body ground Always Below 1 Ω
J46-26 (E2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J46-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR