Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
4WD Control ECU Communication Stop Mode Either condition is met:
·

"Four Wheel Drive Control" is not displayed on the "Bus Check" screen.

·

"4WD Control ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside 4WD control ECU

·

4WD control ECU CAN branch wire or connector

·

4WD control ECU



WIRING DIAGRAM

C352761E03
1.646,0.906 1.75,1.104 0.104,0.198 10 false 2 1.625,1.49 1.792,1.667 0.167,0.177 10 false 13 0.417,1.969 0.646,2.146 0.229,0.177 10 false J74 0.406,2.146 1.948,2.344 1.542,0.198 10 false No. 2 Junction Connector 5.313,1.49 5.479,1.688 0.167,0.198 10 false 22 5.313,0.896 5.469,1.083 0.156,0.188 10 false 23 5.594,1.01 6.01,1.198 0.417,0.188 10 false CANH 5.604,1.594 6.021,1.781 0.417,0.188 10 false CANL 5.573,2.521 5.792,2.719 0.219,0.198 10 false B 5.354,2.396 5.5,2.563 0.146,0.167 10 false 6 5.313,3.219 5.5,3.385 0.188,0.167 10 false 16 5.573,3.313 5.792,3.51 0.219,0.198 10 false IG 5.604,4.146 5.917,4.354 0.313,0.208 10 false GND 5.365,4.052 5.49,4.219 0.125,0.167 10 false 5 5.313,4.802 5.635,4.99 0.323,0.188 10 false A25 5.313,4.99 6.458,5.188 1.146,0.198 10 false 4WD Control ECU 4.115,2.333 4.479,2.51 0.365,0.177 10 false 4WD 3.854,3.125 4.771,3.323 0.917,0.198 10 false ECU-IG1 No.3 2.219,2.5 3.01,2.698 0.792,0.198 10 false from Battery 1.781,3.323 2.99,3.521 1.208,0.198 10 false from IG No.1 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (4WD CONTROL ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (4WD CONTROL ECU CAN BRANCH WIRE)
a.
U152605E01
0.121,0.065 0.356,0.342 0.235,0.276 10 *a 0.748,1.801 1.140,1.939 0.392,0.137 10 CANL 0.588,1.558 1.003,1.695 0.415,0.137 10 CANH 0.544,1.074 0.811,1.211 0.267,0.137 10 A25 1.452,1.383 1.25,1.632 1.25,1.632 1.095,1.632 false 1.224,1.877 1.39,1.877 1.39,1.877 1.526,1.383 false

Disconnect the A25 4WD control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A25-23 (CANH) - A25-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to 4WD Control ECU)



OK

4.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE 4WD CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BATTERY AND BODY GROUND)
a.
U152606E01
0.121,0.065 0.356,0.342 0.235,0.276 10 *a 0.743,0.498 1.077,0.635 0.334,0.137 10 GND 0.791,1.443 0.982,1.581 0.191,0.137 10 IG 0.926,0.853 1.066,0.990 0.140,0.137 10 B 2.632,1.074 2.899,1.211 0.267,0.137 10 A25 1.378,1.268 1.175,1.518 1.175,1.518 1.02,1.518 false 1.378,1.069 1.212,0.922 1.212,0.922 1.092,0.922 false 1.146,0.592 1.313,0.592 1.313,0.592 1.526,1.041 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-5 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A26-6 (B) - Body ground Always 11 to 14 V
A26-16 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to 4WD Control ECU)


OK

REPLACE 4WD CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR