Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM C

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  U1115  Lost Communication with Tilt and Telescopic Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U1115 There is no communication from the multiplex tilt and telescopic ECU.
·

Power source circuit of multiplex tilt and telescopic ECU

·

Multiplex tilt and telescopic ECU CAN branch wire or connector

·

Multiplex tilt and telescopic ECU



For vehicles with a seat memory.


WIRING DIAGRAM

C288316E03
1.798,3.844 3.006,3.983 1.208,0.140 10 from IG No.1 Relay 0.623,1.859 2.296,2.082 1.673,0.223 10 No. 3 Junction Connector 4.992,5.144 5.301,5.355 0.309,0.211 10 J47 5.806,1.306 6.323,1.444 0.517,0.138 10 CANL 5.806,0.865 6.323,1.003 0.517,0.138 10 CANH 5.63,0.779 5.731,0.922 0.101,0.144 10 5 5.806,3.841 6.323,3.979 0.517,0.138 10 IG 5.63,3.755 5.731,3.899 0.101,0.144 10 8 5.806,4.5 6.323,4.638 0.517,0.138 10 GND 5.538,4.414 5.717,4.557 0.179,0.144 10 11 5.806,2.532 6.323,2.670 0.517,0.138 10 +B 5.63,2.445 5.731,2.589 0.101,0.144 10 2 5.806,3.125 6.323,3.263 0.517,0.138 10 ECUB 5.63,3.038 5.731,3.182 0.101,0.144 10 9 5.548,1.217 5.730,1.357 0.182,0.140 10 14 1.926,0.779 2.027,0.922 0.101,0.144 10 2 1.926,1.217 2.108,1.357 0.182,0.140 10 13 4.474,2.393 4.890,2.530 0.416,0.137 10 TI&TE 4.415,2.996 4.948,3.137 0.533,0.141 10 ECU-B1 2.221,2.513 3.010,2.673 0.788,0.160 10 from Battery 4.261,3.713 5.099,3.854 0.838,0.141 10 ECU-IG No.1 4.992,5.3 7.098,5.503 2.106,0.203 10 Multiplex Tilt and Telescopic ECU 0.627,1.686 0.997,1.886 0.370,0.200 10 J76

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE)
a.
U152552E01
1.576,0.426 1.823,0.563 0.248,0.137 10 J47 0.079,0.056 0.368,0.193 0.289,0.137 10 *a 1.725,1.537 1.518,1.961 1.518,1.961 1.364,1.961 false 2.458,1.961 2.246,1.961 2.246,1.961 1.725,1.348 false 0.848,1.879 1.267,2.016 0.419,0.137 10 CANL 2.481,1.879 2.900,2.016 0.419,0.137 10 CANH

Disconnect the J47 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J47-5 (CANH) - J47-14 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)
a.
U152553E01
1.576,0.426 1.823,0.563 0.248,0.137 10 J47 0.079,0.056 0.368,0.193 0.289,0.137 10 *a 1.249,1.512 1.043,1.936 1.043,1.936 0.888,1.936 false 2.705,1.042 2.545,1.042 2.545,1.042 2.37,1.193 false 0.813,0.793 1.025,0.793 1.025,0.793 1.261,1.193 false 2.711,0.721 2.499,0.721 2.499,0.721 2.18,1.193 false 0.464,1.853 0.809,1.990 0.345,0.137 10 GND 2.724,0.636 2.916,0.773 0.192,0.137 10 IG 0.581,0.708 0.773,0.844 0.192,0.137 10 +B 2.726,0.964 3.144,1.101 0.419,0.137 10 ECUB

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J47-11 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J47-2 (+B) - Body ground Always 11 to 14 V
J47-9 (ECUB) - Body ground Always 11 to 14 V
J47-8 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR