Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM C

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  U1002 (CAN No. 2 BUS)  Lost Communication with Gateway Module (Network Gateway ECU)  


DESCRIPTION

·

The network gateway ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN V2 bus.

·

When the network gateway ECU receives a response signal from the ECUs connected to the CAN V2 bus, the network gateway ECU recognizes and memorizes that the ECU is connected to the CAN V2 bus. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to the CAN V2 bus when communicating with those ECUs. If the network gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN V2 bus, the network gateway ECU determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 Lost communication with the gateway module.
·

V2 bus circuit

·

Network gateway ECU CAN main wire or connector

·

Blind spot monitor sensor RH CAN branch wire or connector

·

Network gateway ECU

·

Blind spot monitor sensor RH

·

No. 4 junction connector

·

No. 5 junction connector



For vehicles with a blind spot monitor system.


WIRING DIAGRAM

C288315E03
5.398,1.444 5.772,1.581 0.374,0.137 10 J123 5.398,1.605 6.847,1.742 1.449,0.137 10 Network Gateway ECU 5.619,1.178 6.082,1.315 0.463,0.137 10 CA2L 5.619,0.621 6.082,0.758 0.463,0.137 10 CA2H 5.36,1.013 5.531,1.150 0.172,0.137 10 12 5.36,0.635 5.531,0.772 0.172,0.137 10 13 2.904,3.308 4.494,3.453 1.590,0.145 10 No. 4 Junction Connector 2.904,3.145 3.294,3.281 0.390,0.137 10 R17 5.299,3.308 6.889,3.453 1.590,0.145 10 No. 5 Junction Connector 5.299,3.145 5.690,3.281 0.390,0.137 10 J77 5.439,2.716 5.536,2.853 0.097,0.137 10 2 5.434,2.336 5.536,2.472 0.102,0.137 10 3 5.623,2.896 6.017,3.033 0.394,0.137 10 CANL 5.623,2.334 6.038,2.470 0.415,0.137 10 CANH 0.797,1.415 1.195,1.552 0.397,0.137 10 S6 0.797,1.564 2.730,1.876 1.933,0.312 10 Blind Spot Monitor Sensor RH 1.95,0.999 2.122,1.136 0.172,0.137 10 7 1.95,0.621 2.122,0.758 0.172,0.137 10 2 3.225,0.999 3.332,1.136 0.107,0.137 10 8 3.225,0.621 3.332,0.758 0.107,0.137 10 5 4.005,0.999 4.112,1.136 0.107,0.137 10 4 4.005,0.621 4.112,0.758 0.107,0.137 10 1 4.005,2.714 4.112,2.851 0.107,0.137 10 3 4.005,2.336 4.112,2.472 0.107,0.137 10 2 1.438,1.089 1.832,1.225 0.394,0.137 10 CA1N 1.442,0.706 1.832,0.843 0.390,0.137 10 CA1P

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK CAN BUS WIRE (CHECK MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
3.CHECK CAN BUS WIRE (CHECK MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
a.
U152492E01
1.386,0.948 1.116,0.586 1.116,0.586 1.017,0.586 false 2.062,0.948 2.332,0.586 2.332,0.586 2.431,0.586 false 1.659,1.08 1.923,1.592 1.923,1.592 2.003,1.592 false 1.562,1.08 1.298,1.592 1.298,1.592 1.219,1.592 false 2.022,1.51 2.388,1.651 0.366,0.140 10 CA2L 0.733,1.51 1.124,1.651 0.390,0.140 10 CA2H 0.62,0.505 1.010,0.645 0.390,0.140 10 GND 2.452,0.505 2.842,0.645 0.390,0.140 10 BATT 0.063,0.042 0.369,0.182 0.306,0.140 10 *a 1.502,0.39 1.820,0.527 0.318,0.137 10 J123

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
J123-13 (CA2H) - J123-12 (CA2L) Ignition switch off 54 to 69 Ω Below 53 Ω: Short in line
J123-13 (CA2H) - J123-12 (CA2L) Ignition switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
J123-13 (CA2H) - J123-2 (BATT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
J123-12 (CA2L) - J123-2 (BATT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
J123-13 (CA2H) - J123-4 (GND) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short
J123-12 (CA2L) - J123-4 (GND) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(Network Gateway ECU)

Result
Result Proceed to
NG
·

Open in CAN main bus line


A
NG
·

Short in line

·

+B short

·

GND short


B
OK C



A

4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

B

10.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR RH)

C

19.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)
4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U152566E02
2.115,1.052 2.354,0.656 2.354,0.656 2.5,0.656 false 1.365,1.042 1.115,0.625 1.115,0.625 0.958,0.625 false 0.135,0.125 0.344,0.323 0.208,0.198 10 false *a 0.396,1.229 0.667,1.406 0.271,0.177 10 false R17 0.5,0.531 0.927,0.729 0.427,0.198 10 false CANH 2.563,0.583 2.948,0.781 0.385,0.198 10 false CANL

Disconnect the R17 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R17-1 (CANH) - R17-4 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to No. 4 Junction Connector)



OK

5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

NG

6.CONNECT CONNECTOR
5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U152567E02
1.563,1.031 1.292,0.635 1.292,0.635 1.146,0.635 false 1.854,1.042 2.125,0.646 2.125,0.646 2.271,0.646 false 0.052,0 0.323,0.271 0.271,0.271 10 false *a 0.667,0.573 1.094,0.74 0.427,0.167 10 false CANH 2.344,0.573 2.76,0.75 0.417,0.177 10 false CANL 0.438,1.177 0.719,1.375 0.281,0.198 10 false R17

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R17-2 (CANH) - R17-3 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to No. 4 Junction Connector)



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

8.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the R17 No. 4 junction connector.



NEXT

7.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU)
7.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU)
a.
U152498E01
1.59,1.295 1.238,1.623 1.238,1.623 1.114,1.623 false 1.372,1.895 1.495,1.895 1.495,1.895 1.699,1.293 false 0.624,1.548 1.013,1.686 0.389,0.137 10 CA2H 0.922,1.809 1.311,1.946 0.389,0.137 10 CA2L 0.07,0.056 0.371,0.193 0.301,0.137 10 *a 0.422,1.127 0.749,1.266 0.327,0.139 10 J123

Disconnect the J123 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J123-13 (CA2H) - J123-12 (CA2L) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (NETWORK GATEWAY ECU - NO. 4 JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the R17 No. 4 junction connector.



NEXT

9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR)
9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR)
a.
U152490E02
1.26,0.792 1.01,0.583 1.01,0.583 0.885,0.583 false 1.083,0.25 1.208,0.25 1.208,0.25 1.615,0.802 false 0.396,0.51 0.833,0.688 0.438,0.177 10 false CANH 0.708,0.198 1.135,0.385 0.427,0.188 10 false CANL 0.094,0.104 0.271,0.302 0.177,0.198 10 false *a 2.677,0.885 2.917,1.063 0.24,0.177 10 false J77

Disconnect the J77 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J77-3 (CANH) - J77-2 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)

10.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR RH)
a.
U152568E01
1.437,1.285 1.263,1.69 1.263,1.69 1.112,1.69 false 2.022,1.285 2.196,1.69 2.196,1.69 2.347,1.69 false 2.367,1.609 2.778,1.746 0.411,0.137 10 CANL 0.604,1.609 1.018,1.746 0.414,0.137 10 CANH 0.058,0.06 0.500,0.197 0.442,0.137 10 *a 0.058,1.939 0.500,2.076 0.442,0.137 10 *b 2.208,2.919 2.371,3.211 2.371,3.211 2.526,3.211 false 2.548,3.132 2.937,3.269 0.389,0.137 10 BAT 0.964,2.026 1.353,2.163 0.389,0.137 10 CG 1.647,2.475 1.437,2.101 1.437,2.101 1.282,2.101 false 0.4,2.626 0.643,2.765 0.243,0.139 10 J17 0.47,1.039 0.745,1.178 0.276,0.139 10 R17

Disconnect the R17 No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R17-5 (CANH) - R17-8 (CANL) Ignition switch off 200 Ω or higher
R17-5 (CANH) - J17-4 (CG) Ignition switch off 200 Ω or higher
R17-8 (CANL) - J17-4 (CG) Ignition switch off 200 Ω or higher
R17-5 (CANH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
R17-8 (CANL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to No. 4 Junction Connector)
*b Front view of DLC3



OK

11.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NG

13.CONNECT CONNECTOR
11.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U152569E01
0.4,2.626 0.643,2.765 0.243,0.139 10 J17 0.47,1.039 0.745,1.178 0.276,0.139 10 R17 2.022,0.948 2.196,0.543 2.196,0.543 2.347,0.543 false 1.437,0.948 1.263,0.543 1.263,0.543 1.112,0.543 false 2.367,0.463 2.778,0.600 0.411,0.137 10 CANL 0.604,0.463 1.018,0.600 0.414,0.137 10 CANH 0.058,0.06 0.500,0.197 0.442,0.137 10 *a 0.058,1.939 0.500,2.076 0.442,0.137 10 *b 2.208,2.919 2.371,3.211 2.371,3.211 2.526,3.211 false 2.548,3.132 2.937,3.269 0.389,0.137 10 BAT 0.964,2.026 1.353,2.163 0.389,0.137 10 CG 1.647,2.475 1.437,2.101 1.437,2.101 1.282,2.101 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R17-1 (CANH) - R17-4 (CANL) Ignition switch off 108 to 132 Ω
R17-1 (CANH) - J17-4 (CG) Ignition switch off 200 Ω or higher
R17-4 (CANL) - J17-4 (CG) Ignition switch off 200 Ω or higher
R17-1 (CANH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
R17-4 (CANL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to No. 4 Junction Connector)
*b Front view of DLC3



OK

12.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

NG

15.CONNECT CONNECTOR
12.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U152570E01
0.4,2.626 0.643,2.765 0.243,0.139 10 J17 0.47,1.039 0.745,1.178 0.276,0.139 10 R17 1.825,0.967 2,0.562 2,0.562 2.15,0.562 false 1.631,0.967 1.456,0.562 1.456,0.562 1.306,0.562 false 2.19,0.486 2.601,0.623 0.411,0.137 10 CANL 0.787,0.486 1.201,0.623 0.414,0.137 10 CANH 0.058,0.06 0.500,0.197 0.442,0.137 10 *a 0.058,1.939 0.500,2.076 0.442,0.137 10 *b 2.208,2.919 2.371,3.211 2.371,3.211 2.526,3.211 false 2.548,3.132 2.937,3.269 0.389,0.137 10 BAT 0.964,2.026 1.353,2.163 0.389,0.137 10 CG 1.647,2.475 1.437,2.101 1.437,2.101 1.282,2.101 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R17-2 (CANH) - R17-3 (CANL) Ignition switch off 108 to 132 Ω
R17-2 (CANH) - J17-4 (CG) Ignition switch off 200 Ω or higher
R17-3 (CANL) - J17-4 (CG) Ignition switch off 200 Ω or higher
R17-2 (CANH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
R17-3 (CANL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to No. 4 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

17.CONNECT CONNECTOR
13.CONNECT CONNECTOR
a.

Reconnect the R17 No. 6 junction connector.



NEXT

14.CHECK FOR SHORT IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR RH)
14.CHECK FOR SHORT IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR RH)
a.
U152561E01
0.4,2.695 0.643,2.834 0.243,0.139 10 J17 2.704,1.056 2.897,1.195 0.192,0.139 10 S6 1.571,1.039 1.173,0.656 1.173,0.656 1.022,0.656 false 1.571,1.206 1.173,1.589 1.173,1.589 1.022,1.589 false 0.542,0.585 0.922,0.722 0.380,0.137 10 CA1P 0.531,1.512 0.920,1.649 0.389,0.137 10 CA1N 0.067,0.106 0.509,0.243 0.442,0.137 10 *a 0.067,1.985 0.509,2.122 0.442,0.137 10 *b 2.216,2.965 2.38,3.239 2.38,3.239 2.535,3.239 false 2.557,3.161 2.945,3.298 0.389,0.137 10 BAT 0.956,2.072 1.344,2.209 0.389,0.137 10 CG 1.638,2.521 1.429,2.147 1.429,2.147 1.274,2.147 false

Disconnect the S6 blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
S6-2 (CA1P) - S6-7 (CA1N) Ignition switch off 54 to 69 Ω
S6-2 (CA1P) - J17-4 (CG) Ignition switch off 200 Ω or higher
S6-7 (CA1N) - J17-4 (CG) Ignition switch off 200 Ω or higher
S6-2 (CA1P) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
S6-7 (CA1N) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR RH (CA1P, CA1N)

15.CONNECT CONNECTOR
a.

Reconnect the R17 No. 6 junction connector.



NEXT

16.CHECK FOR SHORT IN CAN BUS WIRE (NETWORK GATEWAY ECU)
16.CHECK FOR SHORT IN CAN BUS WIRE (NETWORK GATEWAY ECU)
a.
U152501E01
0.4,2.688 0.643,2.827 0.243,0.139 10 J17 2.726,1.05 3.048,1.189 0.322,0.139 10 J123 1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.518,1.199 1.237,1.538 1.237,1.538 1.088,1.538 false 1.623,1.199 1.486,1.788 1.486,1.788 1.32,1.788 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.589,1.452 1.013,1.594 0.424,0.142 10 CA2H 0.839,1.702 1.262,1.844 0.424,0.142 10 CA2L 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT

Disconnect the J123 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J123-13 (CA2H) - J123-12 (CA2L) Ignition switch off 108 to 132 Ω
J123-13 (CA2H) - J17-4 (CG) Ignition switch off 200 Ω or higher
J123-12 (CA2L) - J17-4 (CG) Ignition switch off 200 Ω or higher
J123-13 (CA2H) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
J123-12 (CA2L) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (CA2H, CA2L)

17.CONNECT CONNECTOR
a.

Reconnect the R17 No. 4 junction connector.



NEXT

18.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR)
18.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR)
a.
U152500E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.377,0.891 1.138,1.276 1.138,1.276 1.04,1.276 false 1.338,0.314 1.41,0.314 1.41,0.314 1.691,0.708 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.883,0.228 1.272,0.370 0.389,0.142 10 CANL 0.522,1.199 0.946,1.341 0.424,0.142 10 CANH 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.419,2.69 0.663,2.830 0.244,0.140 10 J17 2.679,0.739 2.923,0.879 0.244,0.140 10 J77

Disconnect the J77 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J77-3 (CANH) - J77-2 (CANL) Ignition switch off 108 to 132 Ω
J77-3 (CANH) - J17-4 (CG) Ignition switch off 200 Ω or higher
J77-2 (CANL) - J17-4 (CG) Ignition switch off 200 Ω or higher
J77-3 (CANH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
J77-2 (CANL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)

19.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)
a.
U152497E01
0.406,1.098 0.725,1.235 0.318,0.137 10 J123 2.037,1.295 2.43,1.583 2.43,1.583 2.553,1.583 false 2.215,1.935 2.144,1.935 2.144,1.935 1.929,1.293 false 2.567,1.508 2.956,1.646 0.389,0.137 10 IG2 2.61,0.709 2.999,0.846 0.389,0.137 10 BATT 0.604,0.709 0.993,0.846 0.389,0.137 10 GND 2.234,1.866 2.623,2.004 0.389,0.137 10 IG1 0.07,0.056 0.371,0.193 0.301,0.137 10 *a 1.35,1.097 1.101,0.786 1.101,0.786 1.029,0.786 false 2.278,1.097 2.527,0.786 2.527,0.786 2.598,0.786 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the J123 network gateway ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J123-4 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Condition Specified Condition
J123-2 (BATT) - Body ground Always 11 to 14 V
J123-10 (IG1) - Body ground Ignition switch ON 11 to 14 V
J123-9 (IG2) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR