Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM C

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  U0233  Lost Communication with Blind Spot Monitor Master Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0233 There is no communication from the blind spot monitor sensor RH.
·

Power source or inside of blind spot monitor sensor RH

·

Blind spot monitor sensor RH CAN branch wire or connector

·

Blind spot monitor sensor RH



For vehicles with a blind spot monitor sensor.


WIRING DIAGRAM

C352760E01
1.667,0.729 1.781,0.927 0.115,0.198 10 false 5 1.656,1.323 1.771,1.521 0.115,0.198 10 false 8 0.396,1.823 0.667,2.021 0.271,0.198 10 false R17 0.396,1.99 1.969,2.177 1.573,0.188 10 false No. 4 Junction Connector 5.365,0.74 5.479,0.938 0.115,0.198 10 false 2 5.375,1.313 5.49,1.51 0.115,0.198 10 false 7 5.615,0.854 5.99,1.052 0.375,0.198 10 false CA1P 5.615,1.417 5.99,1.615 0.375,0.198 10 false CA1N 5.635,2.458 5.958,2.625 0.323,0.167 10 false BRB 5.656,3.073 6.104,3.25 0.448,0.177 10 false BRGD 5.375,2.344 5.49,2.542 0.115,0.198 10 false 5 5.323,2.927 5.5,3.125 0.177,0.198 10 false 10 1.771,2.469 2.979,2.667 1.208,0.198 10 false from IG No.1 Relay 3.698,2.302 4.51,2.49 0.813,0.188 10 false ECU-IG No.1 5.115,4.031 5.344,4.198 0.229,0.167 10 false S6 5.125,4.219 6.99,4.406 1.865,0.188 10 false Blind Spot Monitor Sensor RH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR RH CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR RH CAN BRANCH WIRE)
a.
U152559E01
1.599,0.243 1.794,0.381 0.196,0.139 10 S6 0.391,0.624 0.779,0.762 0.388,0.139 10 CA1P 0.391,1.707 0.779,1.845 0.388,0.139 10 CA1N 0.052,0.041 0.365,0.180 0.314,0.139 10 *a 1.51,1.137 1.023,0.699 1.023,0.699 0.874,0.699 false 1.51,1.344 1.023,1.782 1.023,1.782 0.874,1.782 false

Disconnect the S6 blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
S6-2 (CA1P) - S6-7 (CA1N) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE BLIND SPOT MONITOR SENSOR RH CAN BRANCH WIRE OR CONNECTOR (CA1P, CA1N)

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY AND BODY GROUND)
a.
U152560E01
1.599,0.243 1.794,0.381 0.196,0.139 10 S6 2.664,0.624 3.052,0.762 0.388,0.139 10 BRB 2.664,1.707 3.118,1.845 0.454,0.139 10 BRGD 0.052,0.041 0.365,0.180 0.314,0.139 10 *a 1.997,1.137 2.484,0.699 2.484,0.699 2.633,0.699 false 1.997,1.344 2.484,1.782 2.484,1.782 2.633,1.782 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-10 (BRGD) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S6-5 (BRB) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR