Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.08
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P050A  Cold Start Idle Air Control System Performance  


DESCRIPTION

This monitor will run when the engine is started with the engine coolant temperature at -10 to 50°C (14 to 122°F). The DTC will be set after the engine idles for 13 seconds (2 trip detection logic).

The DTC is designed to monitor the idle air control at cold start. When the engine is started with the engine coolant temperature at lower than 50°C (122°F), the ECM (PCM) measures the accumulated mass air flow at engine idling. If it does not reach the criteria within 10 seconds, the ECM (PCM) interprets this as a malfunction. The MIL is illuminated and a DTC is set when the malfunction is detected in consecutive driving cycles (2 trip detection logic).

The ETCS (Electronic Throttle Control System) controls the idle speed. The ETCS operates the throttle actuator to open and close the throttle valve, and adjusts the intake air amount to achieve the target idle speed.

NOTICE:

When the negative battery terminal is disconnected during inspections or repairs, the ISC (Idle Speed Control) learning values are cleared. This DTC cannot be set with the ISC learning values cleared.

The ISC learning is performed when the engine is warmed up and has been idling for 5 minutes.


A124205E05
0.086,0.025 1.888,0.209 1.802,0.184 12 P050A Detection Logic: 1.4,2.863 2.260,3.074 0.860,0.211 10 Engine Start 4.755,1.05 5.676,1.231 0.920,0.181 10 Pass Detected 4.755,2.072 5.547,2.253 0.791,0.181 10 Malfunction 2.111,2.544 2.267,2.725 0.156,0.181 10 0 2.937,2.915 3.632,3.077 0.695,0.162 10 3 seconds 4.604,2.915 5.368,3.078 0.765,0.163 10 13 seconds 2.577,2.657 2.224,2.912 false 4.889,2.577 5.214,2.758 0.326,0.181 10 Time 4.755,1.572 5.342,1.727 0.586,0.156 10 Criterion 1.342,0.764 2.248,1.211 0.906,0.448 10 Accumulated Mass Air Flow 1.953,3.328 5.415,3.493 3.461,0.165 10 Engine Coolant Temperature: -10 to 50°C (14 to 122°F)

DTC Code DTC Detection Condition Trouble Area
P050A Insufficient mass air flow at cold start
(2 trip detection logic)
·

Throttle body

·

Mass air flow meter

·

PCV hose

·

Air cleaner filter

·

Air induction system

·

VVT system

·

ECM

·

Wire harness or connector



MONITOR STRATEGY

Related DTCs P050A: Cold start idle air speed control system
Required sensors/Components (Main) Throttle body
Required sensors/Components (Related) Mass air flow meter
Engine coolant temperature sensor
Frequency of operation Once per driving cycle
Duration 10 seconds
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0300 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0500 (Vehicle speed sensor)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
Battery voltage 8 V or more
Time after engine start 3 seconds or more
Starter OFF
ECT at engine start -10°C (14°F) or more
ECT -10 to 50°C (14 to 122°F)
Engine idling 3 seconds or more
Fuel-cut OFF
Vehicle speed Less than 3 km/h (1.875 mph)
Time after shift position changed 2 seconds or more
Atmospheric pressure 76 kPa (570 mmHg) or more

TYPICAL MALFUNCTION THRESHOLDS

Accumulated mass air flow Less than 116 g (varies with ECT)

CONFIRMATION DRIVING PATTERN

A198821E07
0.763,1.233 1.197,1.451 0.434,0.218 10 Idling 0.092,1.617 1.354,1.814 1.262,0.198 10 Ignition Switch ON 1.768,1.487 1.994,1.646 0.226,0.159 10 [A] 3.283,1.078 3.476,1.271 0.193,0.193 10 [B] 3.043,2.29 4.242,2.474 1.200,0.184 10 1 minute or more 4.823,2.914 5.039,3.107 0.216,0.193 10 [C]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Enter the following menu items: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

7.

Check that "Coolant Temp" in the Data List is within the range of -10 to 50°C (14 to 122°F).

8.

Start the engine and warm it up until the coolant temperature is the same as the coolant temperature in the freeze frame data.

9.

Idle the engine for 1 minute or more [B].

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

11.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P050A.

14.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 3 minutes, let the engine cool down, and then perform steps [A] through [C].



15.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC P050A is output A
DTC P050A and other DTCs are output B

HINT:

If any DTCs other than P050A are output, troubleshoot those DTCs first.




OK

2.READ VALUE USING TECHSTREAM (FUEL TRIM)

NG

2.READ VALUE USING TECHSTREAM (FUEL TRIM)
HINT:

Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.


e.

Read the values displayed on the Techstream.


f.

Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total fuel trim.

Result:

Total of Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values is between -20% and 20%.




OK

3.INSPECT THROTTLE BODY

NG

5.CHECK PCV SYSTEM
3.INSPECT THROTTLE BODY
a.

Check for deposits around the throttle valve and throttle valve condition.

OK:

No deposits around throttle valve and throttle valve moves smoothly.




OK

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)

NG

4.REPAIR OR REPLACE THROTTLE BODY ASSEMBLY
4.REPAIR OR REPLACE THROTTLE BODY ASSEMBLY
a.

Repair or replace throttle body assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL).

HINT:

Perform "Inspection After Repair" after repairing or replacing the throttle body assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
5.CHECK PCV SYSTEM
a.

Check the PCV hose connections (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

OK:

PCV hose is connected correctly and is not damaged.




OK

6.CHECK AIR INDUCTION SYSTEM

NG

10.REPAIR OR REPLACE PCV SYSTEM
6.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>3UR-FE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

7.CHECK AIR CLEANER FILTER

NG

11.REPAIR OR REPLACE AIR INDUCTION SYSTEM
7.CHECK AIR CLEANER FILTER
a.

Visually check that the air cleaner filter is not excessively contaminated with dirt or oil.

OK:

The air cleaner filter element is not excessively contaminated with dirt or oil.




OK

8.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)

NG

12.REPLACE AIR CLEANER FILTER
8.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)

OK

9.READ VALUE USING TECHSTREAM (MAF)

NG

13.CHECK AND REPAIR VVT SYSTEM
9.READ VALUE USING TECHSTREAM (MAF)

OK

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)

NG

15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
10.REPAIR OR REPLACE PCV SYSTEM
a.

Repair or replace the PCV system.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
11.REPAIR OR REPLACE AIR INDUCTION SYSTEM
a.

Repair or replace the air induction system.

HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
12.REPLACE AIR CLEANER FILTER
a.

Replace the air cleaner filter element sub-assembly.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
13.CHECK AND REPAIR VVT SYSTEM
a.

Check and repair the VVT system.

HINT:

Refer to DTC P0011 Inspection Procedure (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0011).




NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
NOTICE:

For this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.


h.

Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P050A.


m.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P050A is output) B



A

CHECK INTERMITTENT PROBLEMS

B

15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
NOTICE:

For this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.


h.

Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P050A.


m.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL (DTC P050A is output) A
NORMAL (DTC is not output) B



A

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

END

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

OK

18.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:
·

If the result of the inspection performed in step 9 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
NOTICE:

For this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.


h.

Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P050A.


m.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P050A is output) B



A

END

B