Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.08
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0171  System Too Lean (Bank 1)  P0172  System Too Rich (Bank 1)  P0174  System Too Lean (Bank 2)  P0175  System Too Rich (Bank 2)  


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and the long-term fuel trims.

The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the Air-Fuel Ratio (A/F) sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.

Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC Code DTC Detection Condition Trouble Area
P0171
P0174
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side
(2 trip detection logic)
·

Air induction system

·

Injector blockage

·

Mass Air Flow (MAF) meter

·

Engine Coolant Temperature (ECT) sensor

·

Fuel pressure

·

Gas leakage from exhaust system

·

Open or short in A/F sensor (for Sensor 1) circuit

·

A/F sensor (for Sensor 1)

·

A/F sensor heater (for Sensor 1)

·

Integration relay

·

A/F sensor heater and integration relay circuits

·

PCV valve and hose

·

PCV hose connections

·

ECM

·

Wire harness or connector


P0172
P0175
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side
(2 trip detection logic)
·

Injector leakage or blockage

·

MAF meter

·

ECT sensor

·

Ignition system

·

Fuel pressure

·

Gas leakage from exhaust system

·

Open or short in A/F sensor (for Sensor 1) circuit

·

A/F sensor (for Sensor 1)

·

A/F sensor heater (for Sensor 1)

·

Integration relay

·

A/F sensor heater and integration relay circuits

·

ECM

·

Wire harness or connector



HINT:
·

When DTC P0171 or P0174 is set, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is set, the actual air-fuel ratio is on the rich side.

·

If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be set. The MIL is then illuminated.

·

When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C [167°F]), the system is functioning normally.



MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air-fuel ratio). If the average fuel trim learning value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and sets a DTC.

Example:

The average fuel trim learning value is +35% or more or -35% or less, the ECM interprets this as a fuel system malfunction.

A369480E07
1.802,1.938 1.521,1.938 false 1.854,3.073 1.49,3.25 false 1.646,0.573 3.458,0.771 1.813,0.198 10 false Fuel Compensation Amount 0.354,1.208 1.302,1.375 0.948,0.167 10 false P0171, P0174 1.896,1.854 2.25,2.042 0.354,0.188 10 false 1.35 1.917,2.99 2.271,3.177 0.354,0.188 10 false 0.65 0.26,1.646 1.469,2.188 1.208,0.542 10 false +35%: Malfunction Threshold of LEAN Condition 1.896,2.417 2.25,2.604 0.354,0.188 10 false 1.0 0.302,2.625 1.292,2.813 0.99,0.188 10 false P0172, P0175 0.292,2.979 1.49,3.542 1.198,0.563 10 false -35%: Malfunction Threshold of RICH Condition

MONITOR STRATEGY

Related DTCs P0171: Fuel trim lean (for Bank 1)
P0172: Fuel trim rich (for Bank 1)
P0174: Fuel trim lean (for Bank 2)
P0175: Fuel trim rich (for Bank 2)
Required Sensors/Components (Main) Fuel system
Required Sensors/Components (Related) A/F sensor, Mass air flow meter, Crankshaft position sensor
Frequency of Operation Continuous
Duration Within 10 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P0500 (Vehicle speed sensor)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
Fuel system status Closed loop
Battery voltage 11 V or more
Either of following conditions 1 or 2 set -
1. Engine speed Below 1100 rpm
2. Engine load 10% or higher
Catalyst monitor Not executed

TYPICAL MALFUNCTION THRESHOLDS

Purge-cut Executing
Either of following conditions 1 or 2 met -
1. Average of short-term fuel trim and long-term fuel trim 35% or more (varies with ECT)
2. Average of short-term fuel trim and long-term fuel trim -35% or less (varies with ECT)

CONFIRMATION DRIVING PATTERN

A199233E01
0.568,0.043 1.536,0.247 0.968,0.205 10 Vehicle Speed 1.247,1.962 1.653,2.139 0.406,0.177 10 Idling 0.442,2.249 1.709,2.405 1.268,0.156 10 Ignition Switch ON 2.009,2.339 2.210,2.540 0.201,0.201 10 [A] 2.529,1.836 2.734,2.013 0.205,0.177 10 [B] 3.324,1.839 3.548,2.011 0.224,0.171 10 [C] 4.797,0.442 5.026,0.615 0.229,0.173 10 [D] 5.622,3.29 5.846,3.461 0.224,0.171 10 [E] 0.414,0.317 1.625,0.480 1.211,0.163 10 120 km/h (75 mph) 0.44,1.198 1.652,1.361 1.211,0.163 10 60 km/h (38 mph) 4.343,2.922 5.541,3.099 1.198,0.177 10 5 minutes or more 2.13,2.992 2.925,3.169 0.795,0.177 10 Warming up 2.858,3.146 4.014,3.323 1.156,0.177 10 2 minutes or more 3.636,0.059 7.009,0.262 3.373,0.202 10 Engine coolant temperature is 75°C (167°F) or higher 3.062,2.043 3.463,0.148 3.463,0.148 3.585,0.148 false

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or more) with all the accessories switched OFF [B].

7.

With the engine warmed up, idle the engine for 2 minutes or more [C].

8.

Drive the vehicle at between 60 km/h and 120 km/h (38 mph and 75 mph) and at an engine speed of between 1400 rpm and 3200 rpm for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0171, P0172, P0174 or P0175.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E] again.



14.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0171, P0172, P0174 or P0175 is output A
P0171, P0172, P0174 or P0175 and other DTCs are output B


HINT:

If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.



A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

OK:

PCV hose is connected correctly and is not damaged.




OK

3.CHECK AIR INDUCTION SYSTEM

NG

3.CHECK AIR INDUCTION SYSTEM
HINT:

If a malfunction occurs when depressing the brake pedal, inspect the brake booster assembly, as there may be a vacuum leak in the brake booster assembly itself.


a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>3UR-FE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage from air induction system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Perform the Control the Injection Volume operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Techstream Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Result
Status of AFS Voltage B1S1 or AFS Voltage B2S1 Status of O2S B1S2 or O2S B2S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal - A
Lean Lean Actual air fuel ratio lean
·

PCV valve and hose

·

PCV hose connections

·

Fuel injector blockage

·

Gas leaks from exhaust system

·

Air induction system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


A
Rich Rich Actual air fuel ratio rich
·

Fuel injector leaks or blockage

·

Gas leaks from exhaust system

·

Ignition system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


A
Lean Lean/Rich Air fuel ratio sensor malfunction
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction
·

Air fuel ratio sensor


B

Lean: During the Control the Injection Volume, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the heated oxygen sensor alternates correctly.



A

5.READ VALUE USING TECHSTREAM (COOLANT TEMP)

B

11.INSPECT AIR-FUEL RATIO SENSOR (HEATER RESISTANCE)
5.READ VALUE USING TECHSTREAM (COOLANT TEMP)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.


e.

Read the Coolant Temp twice, when the engine is both cold and warmed up.

Standard:

With cold engine: Same as ambient air temperature.

With warm engine: Between 75°C and 100°C (167°F and 212°F).


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

6.READ VALUE USING TECHSTREAM (MAF)

NG

6.READ VALUE USING TECHSTREAM (MAF)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.


e.

Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:

Between 18.0 gm/sec and 27.0 gm/sec (shift lever: N; A/C: Off).




OK

7.CHECK FUEL PRESSURE

NG

16.CHECK HARNESS AND CONNECTOR
7.CHECK FUEL PRESSURE

OK

8.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE FUEL SYSTEM

8.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.

OK:

No gas leakage.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

9.CHECK FOR SPARKS AND IGNITION

NG

REPAIR OR REPLACE EXHAUST SYSTEM

9.CHECK FOR SPARKS AND IGNITION

NEXT

10.INSPECT FUEL INJECTOR (INJECTION AND VOLUME)
10.INSPECT FUEL INJECTOR (INJECTION AND VOLUME)
a.

Check the injection volume (See page Engine / Hybrid System>3UR-FE FUEL>FUEL INJECTOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

15.PERFORM CONFIRMATION DRIVING PATTERN

NG

11.INSPECT AIR-FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

12.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

NG

12.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

OK

13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

21.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY)
13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

OK

14.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after repairing or replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

15.PERFORM CONFIRMATION DRIVING PATTERN
15.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Input the DTC: P0171, P0172, P0174 or P0175.


k.

Read DTCs.

Result
Result Proceed to
ABNORMAL (DTC P0171, P0172, P0174 or P0175 is output) A
NORMAL (No DTC is output) B



A

16.CHECK HARNESS AND CONNECTOR

B

END

16.CHECK HARNESS AND CONNECTOR
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read DTCs.

Result
Result Proceed to
DTC P0171, P0172, P0174 or P0175 is output A
DTC is not output B



A

18.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)

B

END

18.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)

OK

19.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:
·

If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0171, P0172, P0174 or P0175 is output B



A

END

B

21.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY)

OK

22.INSPECT INTEGRATION RELAY (A/F)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR