|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | ★ | Precoated part |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
Adhesive 1324 | ★ | Precoated part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 22 | FRONT EXHAUST PIPE ASSEMBLY | 17410 | ( )
|
- | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
2.REMOVE ENGINE FROM ENGINE STAND
88310
3.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY
27020
4.INSTALL GENERATOR WITH REGULATOR ASSEMBLY
for 80A Type:
Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>GENERATOR (for 80A Type)>INSTALLATION
for 100A Type:
Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>GENERATOR (for 100A Type)>INSTALLATION
16620D
5.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
19315
7.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
82121
10.INSTALL ENGINE WIRE
11363A
11.INSTALL FLYWHEEL HOUSING SIDE COVER
28100
12.INSTALL STARTER ASSEMBLY
13.INSTALL WATER HOSE
12305
14.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
|
|
| *a | Temporarily Tighten | - | - |
Install the 2 bolts and nut in the order shown in the illustration.
Connect the air conditioner tube with the clamp.
12372A
15.INSTALL ENGINE MOUNTING INSULATOR LH
|
|
| *a | Temporarily Tighten | - | - |
Install the 4 bolts and nut in the order shown in the illustration.
16.REMOVE ENGINE HANGER
12353
17.INSTALL ENGINE MOUNTING BRACKET CAP
18.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
1. Operate the engine lifter and install the engine assembly with transaxle to the vehicle.
Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.
Connect the front suspension crossmember sub-assembly to the vehicle with the 10 bolts.
Install the engine mounting insulator LH to the engine mounting bracket LH with the 3 bolts and nut in the order shown illustration.
Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut in the order shown illustration.
11361J
20.INSTALL FLYWHEEL HOUSING UNDER COVER
21.INSTALL DRIVE SHAFT ASSEMBLY
17410
22.INSTALL FRONT EXHAUST PIPE ASSEMBLY
45259A
24.INSTALL COLUMN HOLE COVER SILENCER SHEET
88704
25.CONNECT SUCTION HOSE SUB-ASSEMBLY
88711
26.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
23901
27.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly to the fuel pipe.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Install the No. 1 fuel pipe clamp to the fuel tube sub-assembly.
87245
28.CONNECT INLET HEATER WATER HOSE
16290F
29.CONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY
77261D
30.CONNECT FUEL TANK TO CANISTER TUBE
23826
31.CONNECT NO. 1 FUEL VAPOR FEED HOSE
16572D
34.CONNECT NO. 2 RADIATOR HOSE
16571C
35.CONNECT NO. 1 RADIATOR HOSE
36.CONNECT ENGINE WIRE
82662A
37.INSTALL NO. 1 RELAY BLOCK COVER
74404A
38.INSTALL BATTERY CLAMP SUB-ASSEMBLY
17701
40.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17801
41.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
42.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
| *1 | Air cleaner cap sub-assembly clamp | *2 | Guide |
| *a | Top of Vehicle | *b | Right side of vehiclre |
| *c | Stopper | - | - |
Connect the air cleaner cap with air cleaner hose and tighten the hose clamp.
Engage the 2 guides to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.
1. Engage the 2 air cleaner cap sub-assembly clamps to install the air cleaner cap sub-assembly.
Engage the clamp to the air cleaner cap sub-assembly.
1. Connect the mass air flow meter connector.
Connect the ventilation hose to the air cleaner hose.
55701J
43.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
55815E
44.INSTALL NO. 1 FRONT VENTILATOR SEAL
55735A
45.INSTALL WATER GUARD PLATE LH
46.INSTALL WINDSHIELD WIPER MOTOR AND LINK
47.INSTALL AUXILIARY BATTERY
57.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK
51447D
63.INSTALL CENTER NO. 4 ENGINE UNDER COVER
51441C
64.INSTALL ENGINE UNDER COVER RH
51442C
65.INSTALL ENGINE UNDER COVER LH
51410
66.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
67.INSTALL FRONT WHEELS
68. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD