Home › Drivetrain › K320 (MULTIDRIVE / CVT) › PARK / NEUTRAL POSITION SWITCH › 2020.08–2021.07
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438036 PARK / NEUTRAL POSITION SWITCH A

K320 MULTIDRIVE / CVT  PARK / NEUTRAL POSITION SWITCH  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C429226N04
5,0.667 5.75,0.833 0.75,0.167 4.583,2.25 5.625,2.417 1.042,0.167 4.958,0.625 5.792,0.875 0.833,0.25 4.25,2.333 4.583,2.333 false 4.698,1.01 4.833,0.75 4.833,0.75 5,0.75 false 2.75,2.448 3.25,2.448 false 2.75,1.417 3.354,1.417 false 3.969,0.667 4.302,0.667 false 2.688,2.052 3.021,2.052 false 2.563,1.281 2.875,1.667 0.313,0.385 18 false 3 2.583,2.313 2.958,2.667 0.375,0.354 18 false 1 4.344,0.594 4.5,0.75 0.156,0.156 10 false ● 4.271,2.333 4.583,2.49 0.313,0.156 10 false x2 2.49,1.917 2.865,2.271 0.375,0.354 18 false 2 5.063,0.688 5.74,0.896 0.677,0.208 8 false 12.7 (130, 9) 4.656,2.271 5.729,2.479 1.073,0.208 8 false 5.4 (55, 48 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PARK/NEUTRAL POSITION SWITCH ASSEMBLY 84540 (Click here) - -
2 TRANSMISSION CONTROL SHAFT LEVER 33572C (Click here) - -
3 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part - -

C446838N02
5.24,1.49 6.083,1.656 0.844,0.167 0.896,0.146 1.896,0.313 1,0.167 1.469,0.969 1.802,0.969 false 1.5,1.781 1.833,1.781 false 1.594,2.583 1.927,2.583 false 4.104,1.073 4.438,1.073 false 5.198,2.25 5.531,2.25 false 4.906,1.583 5.24,1.583 false 6.458,0.25 6.792,0.25 false 6.417,0.698 6.75,0.698 false 6.552,1.021 6.719,1.021 false 0.896,0.229 0.729,0.229 0.729,0.229 0.646,0.646 true 5.615,2.094 5.896,2.448 0.281,0.354 18 false 4 3.896,0.938 4.177,1.292 0.281,0.354 18 false 5 1.99,2.417 2.271,2.771 0.281,0.354 18 false 6 1.896,1.646 2.177,2 0.281,0.354 18 false 7 1.865,0.813 2.146,1.167 0.281,0.354 18 false 8 5.729,0.125 6.521,0.438 0.792,0.313 18 false 10, 12 6.219,0.542 6.573,0.906 0.354,0.365 18 false 9 5.292,1.521 6.417,1.719 1.125,0.198 8 false 15.4 (157, 11) 4.906,1.583 5.219,1.781 0.313,0.198 10 false x3 0.948,0.156 2.292,0.344 1.344,0.188 8 false 3.0 (31, 27 in.*lbf) 5.406,0.896 6.833,1.188 1.427,0.292 18 false 11, 13, 14

Procedure Part Name Code
Z101186

Z101188

Z101187

4 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -
5 ECM 89661 - - -
6 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -
7 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
8 AIR CLEANER CAP WITH AIR CLEANER HOSE - - - -
9 CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
10 INSPECT SHIFT LEVER POSITION - (Click here) - -
11 ADJUST SHIFT LEVER POSITION - - - (Click here)
12 INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY 84540 (Click here) - -
13 ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY 84540 - - (Click here)
14 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 84540 1.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C431782C01
5.875,2.354 6.208,2.302 6.208,2.302 5.865,2.531 true 0.719,3.146 0.927,3.333 0.208,0.188 10 true *a 6.24,2.24 6.552,2.396 0.313,0.156 10 false *b 0.583,0.083 1,0.417 0.417,0.333 18 true i, vi 3.917,0.083 4.448,0.417 0.531,0.333 18 true ii, iv 0.583,2.083 0.833,2.333 0.25,0.25 18 true iii 3.917,2.083 4.167,2.333 0.25,0.25 18 true v
*a N *b Protrusion


i.

Temporarily install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.


ii.

Temporarily install the transmission control shaft lever to the manual valve lever shaft.


iii.

Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

NOTICE:
C432070C02
1.458,0.417 1.667,0.167 1.667,0.167 1.833,0.167 true 1.833,1.323 2.333,0.583 2.333,0.583 2.5,0.583 true 1.479,1.833 1.896,1.833 true 1.885,0.104 2.167,0.344 0.281,0.24 10 false *1 2.542,0.521 2.823,0.76 0.281,0.24 10 false *2 1.271,1.771 1.469,1.917 0.198,0.146 10 true *3
*1 Transmission Control Shaft Lever
*2 Manual Valve Link Lever Sub-assembly
*3 Manual Valve


If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.



iv.

Remove the transmission control shaft lever from the manual valve lever shaft.


v.

Align the protrusions of the park/neutral position switch assembly as shown in the illustration.


vi.

Hold the park/neutral position switch assembly in that position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)



Hide 35572C 2.CONNECT TRANSMISSION CONTROL SHAFT LEVER

a.
C431093N02
0.583,0.104 0.781,0.417 0.198,0.313 18 true ii 3.885,0.063 4.021,0.375 0.135,0.313 18 true i

i.

Install the transmission control shaft lever to the manual valve lever shaft with the washer and nut.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:

Be careful of the direction of the transmission control shaft lever.



ii.

Connect the park/neutral position switch connector.



Hide 33820B 3.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Z101186

NOTICE:

Before connecting the transmission control cable assembly, check that the shift lever is in N.



a.
C431095C01
0.948,1.177 1.146,1.354 0.198,0.177 10 true *a 3.021,3.792 3.333,3.948 0.313,0.156 10 false *b 4.083,3.792 4.396,3.948 0.313,0.156 10 false *c 0.688,0.135 0.885,0.417 0.198,0.281 18 true i 4.031,0.115 4.229,0.396 0.198,0.281 18 true ii 2.094,2.052 2.375,2.333 0.281,0.281 18 true iii
*a N *b Correct
*c Incorrect - -


i.

Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

NOTICE:
C432070C02
1.458,0.417 1.667,0.167 1.667,0.167 1.833,0.167 true 1.833,1.323 2.333,0.583 2.333,0.583 2.5,0.583 true 1.479,1.833 1.896,1.833 true 1.885,0.104 2.167,0.344 0.281,0.24 10 false *1 2.542,0.521 2.823,0.76 0.281,0.24 10 false *2 1.271,1.771 1.469,1.917 0.198,0.146 10 true *3
*1 Transmission Control Shaft Lever
*2 Manual Valve Link Lever Sub-assembly
*3 Manual Valve


If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.



ii.

Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


iii.

Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.



Hide 74404A 4.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 17701 6.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 7.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 8.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 9.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 84540 12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Hide 84540 13.ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Hide 14. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART