|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
33820B
1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
|
|
| *a | N | - | - |
Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.
| *1 | Transmission Control Shaft Lever |
| *2 | Manual Valve Link Lever Sub-assembly |
| *3 | Manual Valve |
If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.
Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.
Engage the guide to connect the transmission control cable assembly to vehicle body.
Install the nut.
| *a | Correct | *b | Incorrect |
Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.
| *1 | Adjuster Case | *2 | Adjuster Case Cover |
| *3 | Lock Piece | - | - |
Slide the adjuster case cover in the direction shown by the arrow.
Using a precision screwdriver, pull out the lock piece of the adjuster case.
| *1 | Lock Nut | *2 | Stopper |
| *a | Push in | - | - |
Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.
Connect the transmission control cable assembly to the transmission floor shift assembly.
After installation, check that the outer part of the stopper is as shown in the illustration.
Do not forcibly pull the transmission control cable assembly into the cabin.
Connect the transmission control cable assembly to the transmission floor shift assembly.
Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.
Connect the transmission control cable assembly so that the lock piece faces the driver side.
Before connecting the floor shift transmission control select cable, check that the shift lever is in N.
| *1 | Adjuster Case | *2 | Lock Piece |
| *3 | Adjuster Case Cover | - | - |
Push in the lock piece of the adjuster case to lock it.
| *1 | Transmission Control Cable Assembly |
| *2 | Lever Shaft |
When pushing in the lock piece of the adjuster case to lock it, remove your hand from the lever shaft.
When pushing in the lock piece of the adjuster case to lock it, do not move the lever shaft or transmission control cable assembly forward or backward.
Move the adjuster case cover in the direction shown by the arrow.
If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the cable will not be able to lock, and reliable shift operation will not be possible.
2.INSTALL REAR CONSOLE BOX ASSEMBLY
58153
3.INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR
58151
4.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR
51447D
6.INSTALL CENTER NO. 4 ENGINE UNDER COVER
74404A
7.INSTALL BATTERY CLAMP SUB-ASSEMBLY
89661
8.INSTALL ECM
17701
9.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17801
10.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
11.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
13.INSPECT SHIFT LEVER POSITION
14.ADJUST SHIFT LEVER POSITION
15.INSPECT FOR EXHAUST GAS LEAK
16. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART