Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM › 2020.08–2021.07
RM3700E _58 Vehicle Interior _092990 SEAT _0438277 SEAT HEATER SYSTEM J

SEAT  SEAT HEATER SYSTEM  Seat Heater for Front Right Seat does not Operate  


DESCRIPTION

When the seat heater switch is operated, the power distribution box assembly receives the signal. The power distribution box assembly receives the signal and operates the front seat heater.

WIRING DIAGRAM

E426742E01
3.021,7.865 4.708,8.406 1.688,0.542 10 false Front Seat Cushion Heater Assembly RH 4.49,0.24 4.896,0.479 0.406,0.24 10 false E 6.083,0.24 6.552,0.458 0.469,0.219 10 false LO 5.313,1.927 5.646,2.188 0.333,0.26 10 false *1 4.677,1.438 6.448,1.75 1.771,0.313 10 false Seat Heater Switch RH 2.75,4.125 3.917,4.344 1.167,0.219 10 false S/HTR F/R 1.875,0.927 3.052,1.323 1.177,0.396 10 false from IGP Relay 2.292,3.125 2.76,3.396 0.469,0.271 10 false +B1 3.792,3.667 4.958,3.885 1.167,0.219 10 false IC 3.208,1.146 4.958,1.323 1.75,0.177 10 false ECU-IGP NO. 3 4.479,0.865 4.948,1.083 0.469,0.219 10 false IG 3.896,2.021 4.302,2.26 0.406,0.24 10 false SHIN 2.833,5 5.906,5.333 3.073,0.333 10 false Power Distribution Box Assembly 2.583,2.49 5.01,2.813 2.427,0.323 10 false Air Conditioning Amplifier Assembly 0.208,8.365 1.729,8.625 1.521,0.26 10 false *1: for HV Model 6.042,3.635 6.375,3.896 0.333,0.26 10 false 4B 6.083,3.438 6.417,3.698 0.333,0.26 10 false 7 6.042,4.635 6.375,4.896 0.333,0.26 10 false 4C 6.052,4.448 6.385,4.708 0.333,0.26 10 false 25 1.563,3.833 1.896,4.094 0.333,0.26 10 false 4C 1.563,3.656 1.896,3.917 0.333,0.26 10 false 40 1.031,6.375 1.5,6.594 0.469,0.219 10 false 7 1.031,7.271 1.5,7.49 0.469,0.219 10 false 5 5.156,5.563 5.625,5.781 0.469,0.219 10 false 2 5.156,6.396 5.625,6.615 0.469,0.219 10 false 3 5.156,7.271 5.625,7.49 0.469,0.219 10 false 1 5.146,5.75 5.615,5.969 0.469,0.219 10 false A 5.146,6.583 5.615,6.802 0.469,0.219 10 false A 5.156,7.469 5.625,7.688 0.469,0.219 10 false A 0.938,6.573 1.406,6.792 0.469,0.219 10 false Ov1 0.948,7.458 1.417,7.677 0.469,0.219 10 false Ov1 6.396,0.24 6.729,0.5 0.333,0.26 10 false 2 4.271,0.24 4.604,0.5 0.333,0.26 10 false 4 4.271,0.865 4.604,1.125 0.333,0.26 10 false 5 2.594,2.333 3,2.573 0.406,0.24 10 false H24 4.323,1.927 4.729,2.167 0.406,0.24 10 false 26 4.677,1.281 5.146,1.5 0.469,0.219 10 false H50 5.385,7.854 6.833,8.396 1.448,0.542 10 false Front Seatback Heater Assembly RH 2.438,7.458 2.906,7.677 0.469,0.219 10 false v3 2.438,6.563 2.906,6.781 0.469,0.219 10 false v3 2.448,6.385 2.917,6.604 0.469,0.219 10 false 1 2.458,7.271 2.927,7.49 0.469,0.219 10 false 3 1.177,7.896 2.698,8.156 1.521,0.26 10 false Front Seat Wire RH

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The seat heater system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the seat heater system after confirming that the communication system is functioning properly.

Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the auxiliary battery voltage is low, the seat heater system may not operate. When "High Power Consumption Partial Limit On AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the auxiliary battery, referring to On-vehicle Inspection for the charging system.




PROCEDURE

1.READ VALUE USING GTS (Seat A/C System No. 1 Input Signal)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat A/C System No.1 Input Signal Front RH side seat heater drive signal (Input) OFF/ON OFF: Seat heater switch RH off
ON: Seat heater switch RH on
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Seat A/C System No.1 Input Signal
50003 475 1322
OK:

The GTS display changes correctly in response to the seat heater switch RH condition.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FRONT SEAT WIRE RH - POWER DISTRIBUSION BOX ASSEMBLY AND BODY GROUND)

NG

6.CHECK POWER DISTRIBUTION BOX ASSEMBLY (SEAT HEATER SWITCH RH INPUT SIGNAL)
2.CHECK HARNESS AND CONNECTOR (FRONT SEAT WIRE RH - POWER DISTRIBUSION BOX ASSEMBLY AND BODY GROUND)
a.

Disconnect the 4C power distribution box assembly connector.


b.

Disconnect the Ov1 front seat wire RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Ov1)Location & Routing

Click Connector(Ov1)Seat>Floor Wire>Floor Wire and Front Seat Wire RH

Ov1-7 - 4C-40 Always Below 1 Ω
Ov1-7 - body ground Always 10 kΩ or higher
Ov1-5 - body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT SEAT WIRE RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FRONT SEAT WIRE RH
a.

Disconnect the v3 front seat cushion heater assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Ov1,v3)Location & Routing

Click Connector(Ov1)Seat>Floor Wire>Floor Wire and Front Seat Wire RH

Click Connector(v3)Seat>Front Seat Wire LH / Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Heater Assembly RH

Ov1-7 - v3-1 Always Below 1 Ω
Ov1-7 - Body ground Always 10 kΩ or higher
Ov1-5 - v3-3 Always Below 1 Ω
Ov1-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY RH

NG

REPLACE FRONT SEAT WIRE RH

4.INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY RH

OK

5.INSPECT FRONT SEATBACK HEATER ASSEMBLY RH

NG

REPLACE FRONT SEAT CUSHION HEATER ASSEMBLY RH

5.INSPECT FRONT SEATBACK HEATER ASSEMBLY RH

Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER>INSPECTION

Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPLACE FRONT SEATBACK HEATER ASSEMBLY RH

6.CHECK POWER DISTRIBUTION BOX ASSEMBLY (SEAT HEATER SWITCH RH INPUT SIGNAL)
a.

Disconnect the 4B power distribution box assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4B-7 - Body ground Seat heater switch RH on 11 to 14 V



Result:
Result Proceed to
OK A
NG (for HV Model) B
NG (for Gasoline Model) C



A

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

B

7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUSION BOX ASSEMBLY - SEAT HEATER SWITCH RH AND AIR CONDITIONING AMPLIFIER ASSEMBLY)

C

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUSION BOX ASSEMBLY - SEAT HEATER SWITCH RH)
7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUSION BOX ASSEMBLY - SEAT HEATER SWITCH RH AND AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the 4C power distribution box assembly connector.


b.

Disconnect the H50 seat heater switch RH connector.


c.

Disconnect the H24 air conditioning amplifier assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H50,H24)Location & Routing

Click Connector(H50)Instrument Panel>Instrument Panel Wire / Speaker Wire>Seat Heater Switch RH

Click Connector(H24)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assembly

4B-7 - H50-2 (LO) Always Below 1 Ω
4B-7 - H24-26 (SHIN) Always Below 1 Ω
4B-7 - body ground Always 10 kΩ or higher
4C-25 - body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SEAT HEATER SWITCH RH - POWER SOURCE AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SEAT HEATER SWITCH RH - POWER SOURCE AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H50)Location & Routing

Click Connector(H50)Instrument Panel>Instrument Panel Wire / Speaker Wire>Seat Heater Switch RH

H50-5 (IG) - Body ground Ignition switch ON 11 to 14 V
H50-5 (IG) - Body ground Ignition switch off Below 1 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H50)Location & Routing

Click Connector(H50)Instrument Panel>Instrument Panel Wire / Speaker Wire>Seat Heater Switch RH

H50-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT SEAT HEATER SWITCH RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT SEAT HEATER SWITCH RH

Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE SEAT HEATER SWITCH RH

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUSION BOX ASSEMBLY - SEAT HEATER SWITCH RH)
a.

Disconnect the 4C power distribution box assembly connector.


b.

Disconnect the H50 seat heater switch RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H50)Location & Routing

Click Connector(H50)Instrument Panel>Instrument Panel Wire / Speaker Wire>Seat Heater Switch RH

4B-7 - H50-2 (LO) Always Below 1 Ω
4B-7 - body ground Always 10 kΩ or higher
4C-25 - body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (SEAT HEATER SWITCH RH - POWER SOURCE AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (SEAT HEATER SWITCH RH - POWER SOURCE AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H50)Location & Routing

Click Connector(H50)Instrument Panel>Instrument Panel Wire / Speaker Wire>Seat Heater Switch RH

H50-5 (IG) - Body ground Ignition switch ON 11 to 14 V
H50-5 (IG) - Body ground Ignition switch off Below 1 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H50)Location & Routing

Click Connector(H50)Instrument Panel>Instrument Panel Wire / Speaker Wire>Seat Heater Switch RH

H50-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SEAT HEATER SWITCH RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR