Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2020.08–2021.07
RM3700E _55 Steering _093030 STEERING COLUMN _0438540 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C431406N01
5.948,1.667 6.365,1.667 false 6.469,1.542 6.75,1.896 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING WHEEL ASSEMBLY 45100 - - -

C441753N01
4.969,0.333 5.302,0.333 false 2.844,2.823 2.844,2.146 false 5.042,3.396 5.042,3.052 false 5.365,0.198 5.646,0.552 0.281,0.354 18 false 3 2.885,2.813 3.417,3.146 0.531,0.333 18 false 4 5.104,3.385 5.385,3.74 0.281,0.354 18 false 2 6.563,2.052 6.875,2.25 0.313,0.198 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

2 LOWER STEERING COLUMN COVER 45287 (Click here) - -
3 UPPER STEERING COLUMN COVER 45286B - - -
4 TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY - (Click here) - -

C441796N02
4.156,1.365 4.573,1.365 false 5.865,1.635 6.198,1.635 false 4.99,3.365 5.323,3.365 false 3.656,2.208 3.99,2.208 false 1.208,2.292 1.542,2.292 false 2.281,0.969 2.615,0.969 false 0.896,3.24 1.229,3.24 false 2.063,5.104 2.396,5.104 false 1.604,3.813 1.938,3.813 false 5.594,4.198 5.927,4.198 false 2.563,2.708 2.875,2.906 0.313,0.198 10 false x2 2.448,4.979 2.729,5.333 0.281,0.354 18 false 5 5.375,3.229 5.656,3.583 0.281,0.354 18 false 7 5.979,4.073 6.26,4.427 0.281,0.354 18 false 6 1.448,3.677 1.729,4.031 0.281,0.354 18 false 8 6.24,1.51 6.521,1.865 0.281,0.354 18 false 9 4.844,1.26 5.396,1.615 0.552,0.354 18 false 10 4.042,2.063 4.594,2.417 0.552,0.354 18 false 11 1.99,0.833 2.542,1.188 0.552,0.354 18 false 12 0.906,2.146 1.458,2.5 0.552,0.354 18 false 13 0.594,3.104 1.146,3.458 0.552,0.354 18 false 14 2.708,4.115 3.021,4.313 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

5 FRONT CONSOLE BOX SUB-ASSEMBLY 58810J - - -
6 FRONT DOOR SCUFF PLATE RH 67913B - - -
7 COWL SIDE TRIM BOARD RH 62111C - - -
8 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
9 FRONT DOOR OPENING TRIM WEATHERSTRIP RH 62311B - - -
10 NO. 1 INSTRUMENT SIDE PANEL 55317E (Click here) - -
11 HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 53601 - - -
12 LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY 55480D - - -
13 STOP LIGHT SWITCH ASSEMBLY 84340 - - -
14 NO. 1 AIR DUCT 87211 - - -

C441754N02
2.938,1.396 3.073,1.396 false 1.896,3.115 2.292,3.115 false 5.906,1.021 6.302,1.021 false 2.24,1.24 3.896,1.594 1.656,0.354 18 false 16, 17 2.344,2.979 2.854,3.375 0.51,0.396 18 false 15 6.344,0.885 6.854,1.281 0.51,0.396 18 false 18 5.323,2.042 5.729,2.271 0.406,0.229 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

15 COLUMN HOLE COVER SILENCER SHEET 45259A - - -
16 DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 (Click here) - -
17 REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 (Click here) - -
18 STEERING COLUMN ASSEMBLY - - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the electric power steering column sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When the steering sensor is replaced with a new one, ECU security key is necessary.

Electric power steering column sub-assembly Assist map writing
·

There is a difference in steering effort between turning left and right.

·

Vehicle control history (RoB) are stored


(Click here)
Steering sensor (Including removal and installation) Steering angle setting Parking assist monitor system (Click here)
Adjust steering angle Panoramic view monitor system (Click here)
Steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Steering sensor Update ECU security key* Vehicle control history (RoB) are stored (Click here)
w/ Entry and Start System:
Steering lock ECU (Steering lock actuator assembly)
Code registration
for HV Model:
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, HV model)

·

Entry and start system (for Start function, HV model)

·

Hybrid control system cannot be started


for Gasoline Model:
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, Gasoline model)

·

Entry and start system (for Start function, Gasoline model)

·

Engine start function


See Service Bulletin for the registration method

PROCEDURE

Hide 45100 1.REMOVE STEERING WHEEL ASSEMBLY

Hide 45287 2.REMOVE LOWER STEERING COLUMN COVER

Z101186

NOTICE:

Removing the lower steering column cover in the incorrect order will cause the parts to break.



a.
C441755C02
0.49,2.99 0.781,3.313 0.292,0.323 18 false vi 1.438,1.552 1.625,1.854 0.188,0.302 18 true i 4.083,0.125 4.344,0.458 0.26,0.333 18 true v 2.927,1.594 3.104,1.917 0.177,0.323 18 true ii 1.469,0.927 1.719,1.219 0.25,0.292 18 true iv 3.115,0.458 3.344,0.781 0.229,0.323 18 true iii
V100155

Push Area
V100135

Release
V100136

Lock
V100137

Down
V100138

Extend
V113147

Push in this direction


i.

Release the tilt and telescopic lever.


ii.

Fully down the lower the steering column assembly.


iii.

Fully extend the lower the steering column assembly.


iv.

Lock the tilt and telescopic lever.


v.

Remove the 3 screws.


vi.

While pressing the push area shown in the illustration to disengage the claws, slightly lower the lower steering column cover.



Hide 45286B 3.REMOVE UPPER STEERING COLUMN COVER

a.
C441756


Hide 4.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

Z101186

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.




a.
C441757N01
4.125,0.198 4.563,0.51 0.438,0.313 18 true ii, iii 0.542,0.156 0.677,0.458 0.135,0.302 18 false i

i.

Disconnect the 4 connectors from the turn signal switch assembly with spiral cable sub-assembly.


ii.

Using pliers, expand the clamp.


iii.

While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.



Hide 58810J 5.REMOVE FRONT CONSOLE BOX SUB-ASSEMBLY

Hide 67913B 6.REMOVE FRONT DOOR SCUFF PLATE RH

Hide 62111C 7.REMOVE COWL SIDE TRIM BOARD RH

Hide 55606 8.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62311B 9.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 55317E 10.REMOVE NO. 1 INSTRUMENT SIDE PANEL

Hide 53601 11.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55480D 12.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 84340 13.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 45259A 15.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C431396


Hide 45260 16.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C441758C01
4.458,1.552 4.708,1.573 4.708,1.573 4.49,1.469 true 4.208,0.927 4.344,1.188 0.135,0.26 18 true i 2.823,1.01 3.063,1.292 0.24,0.281 18 true ii 3.979,0.5 4.219,0.781 0.24,0.281 18 true iii 4.75,1.49 4.948,1.688 0.198,0.198 10 true *a
*a Matchmark - -
V113147

Disconnect in this direction - -


i.

Put matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.


ii.

Remove the bolt.


iii.

Disconnect the No. 2 steering intermediate shaft assembly from the steering gear assembly.



Hide 45260 17.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C441759C01
2.302,0.531 2.458,0.375 2.458,0.375 2.26,0.458 true 2.844,0.604 3,0.854 0.156,0.25 18 true ii 4.01,0.448 4.26,0.719 0.25,0.271 18 true iii 2.042,0.073 2.177,0.333 0.135,0.26 18 true i 2.5,0.271 2.688,0.458 0.188,0.188 10 true *a
*a Matchmark - -
V113147

Remove in this direction - -


i.

Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.


ii.

Remove the bolt.


iii.

Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.



Hide 18.REMOVE STEERING COLUMN ASSEMBLY

a.
C441760