Home › Engine / Hybrid System › M15A-FKS (FUEL) › FUEL TANK › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093308 M15A-FKS FUEL _0440426 FUEL TANK A

M15A-FKS FUEL  FUEL TANK  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A472817N06
6.469,0.25 6.802,0.25 false 6.375,1.75 6.708,1.75 false 1.188,1.75 1.521,1.75 true 3.771,1.958 4.083,2.156 0.313,0.198 10 false x5 4.448,2.063 4.76,2.26 0.313,0.198 10 false x3 6,0.104 6.552,0.417 0.552,0.313 18 false 1, 2 6.771,1.604 7.073,1.917 0.302,0.313 18 false 3 0.938,1.594 1.167,1.885 0.229,0.292 18 true 4 2.313,2.396 2.625,2.594 0.313,0.198 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DRAIN FUEL - (Click here) - -
3 WHEEL ASSEMBLY - - - -
4 REAR WHEEL HOUSE LINER LH 65638 - - -

A472051N02
6.156,3.438 6.49,3.438 false 1.917,4.646 2.25,4.646 false 3.854,0.333 4.021,0.333 false 4.885,0.417 5.135,0.417 false 5.875,1.677 6.208,1.677 false 5.521,2.115 5.854,2.115 false 6.479,1.333 6.813,1.333 false 5.396,3.063 5.396,3.396 false 4.865,3.292 4.865,3.625 false 2.375,3.906 2.708,3.906 false 2.146,2.427 2.479,2.427 false 2.042,0.906 2.375,0.906 false 5.021,1.604 5.188,1.271 5.188,1.271 5.354,1.271 false 4.292,4.917 4.292,5.25 false 1.031,4.917 1.031,5.25 false 2.531,3.344 2.844,3.542 0.313,0.198 10 false x4 3.302,4.521 3.615,4.719 0.313,0.198 10 false x3 2.448,5.229 2.656,5.375 0.208,0.146 10 false x2 2.76,5.49 2.969,5.635 0.208,0.146 10 false x2 6.167,4.292 6.375,4.438 0.208,0.146 10 false x2 6.021,4.635 6.229,4.781 0.208,0.146 10 false x2 6.552,3.365 6.719,3.542 0.167,0.177 10 false ● 2.323,4.573 2.49,4.75 0.167,0.177 10 false ● 1.823,0.75 2.104,1.104 0.281,0.354 18 false 5 6.865,1.177 7.052,1.531 0.188,0.354 18 false 6 6.438,1.552 6.802,1.906 0.365,0.354 18 false 12 5.417,1.104 5.781,1.458 0.365,0.354 18 false 17 5.406,0.26 6.219,0.594 0.813,0.333 18 false 11, 14 3.146,0.188 3.948,0.458 0.802,0.271 18 false 10, 15 1.833,2.26 2.24,2.594 0.406,0.333 18 false 13 2.177,3.771 2.458,4.125 0.281,0.354 18 false 8 4.229,5.281 4.51,5.635 0.281,0.354 18 false 8 5.281,3.438 5.667,3.75 0.385,0.313 18 false 19 4.74,3.646 5.104,3.979 0.365,0.333 18 false 18 5.896,1.969 6.26,2.323 0.365,0.354 18 false 16 5.156,3.51 5.323,3.688 0.167,0.177 10 false ● 0.969,5.271 1.25,5.625 0.281,0.354 18 false 7 0.75,5.292 0.958,5.438 0.208,0.146 10 false x2 1.438,4.958 1.646,5.104 0.208,0.146 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

5 FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY 77020A - - -
6 FUEL TANK CAP ASSEMBLY 77310A - - -
7 CENTER NO. 4 ENGINE UNDER COVER 51447D - - -
8 FRONT EXHAUST PIPE ASSEMBLY 17410 - -
9 NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY 77606 - - -
10 DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY 77027B (Click here) - -
11 DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY 77209F (Click here) - -
12 FUEL TANK FILLER PIPE SUB-ASSEMBLY - (Click here) - -
13 FUEL TANK ASSEMBLY 77100U (Click here) - -
14 REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY 77209F - - -
15 REMOVE NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY 77027B - - -
16 NO. 2 FUEL TANK FILLER PIPE SUPPORT 77217C - - -
17 NO. 1 FUEL TANK FILLER PIPE SUPPORT 77216A - - -
18 NO. 3 FUEL TANK FILLER PIPE SUPPORT 77218A - - -
19 FUEL TANK FILLER PIPE PROTECTOR 77277R - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Gas leaks from exhaust system is repaired Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

a.
A476525C02
2.688,0.313 3.198,0.448 false 2.51,0.219 2.823,0.417 0.313,0.198 10 false *a 0.385,0.063 0.667,0.417 0.281,0.354 18 false i
*a Cord - -


i.

When removing and storing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using a cord or similar.

NOTICE:

Depending on the arrangement of the inlet hose during storage, the inlet hose and rear suspension may interfere and cause fuel leakage.




Hide 2.DRAIN FUEL

Hide 3.REMOVE WHEEL ASSEMBLY

Hide 65638 4.SEPARATE REAR WHEEL HOUSE LINER LH

a.
A472818


Hide 77020A 5.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 77310A 6.REMOVE FUEL TANK CAP ASSEMBLY

a.
A461413


Hide 51447D 7.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 17410 8.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Z101186

Click here(Click here)

Hide 77606 9.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A459617


Hide 77027B 10.DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY

a.
A459620N03
0.417,0.083 0.698,0.438 0.281,0.354 18 false i

i.

Disconnect the No. 1 fuel emission tube sub-assembly from the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 77209F 11.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A459623N03
0.427,0.073 0.708,0.427 0.281,0.354 18 false i

i.

Disconnect the fuel tank main tube sub-assembly from the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 12.DISCONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY

a.
A457028N01
0.781,0.156 0.958,0.479 0.177,0.323 18 true i 5.99,0.219 6.167,0.542 0.177,0.323 18 true ii

i.

Remove the bolt.


ii.

Disengage the locations shown in the illustration, and disengage the fuel tank filler pipe sub-assembly from the vehicle body.



Hide 77100U 13.REMOVE FUEL TANK ASSEMBLY

Z101186

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.



a.
A461415N02
0.417,0.125 0.698,0.479 0.281,0.354 18 false i 3.656,0.125 3.938,0.479 0.281,0.354 18 false ii 1.875,1.958 2.156,2.313 0.281,0.354 18 false iii

i.

Support the fuel tank assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



ii.

Remove the 4 bolts.


iii.

Lower the engine lifter to remove the fuel tank assembly.

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.





Hide 77209F 14.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A459632


Hide 77027B 15.REMOVE NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY

a.
A459635


Hide 77217C 16.REMOVE NO. 2 FUEL TANK FILLER PIPE SUPPORT

a.
A459638


Hide 77216A 17.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT

a.
A459641


Hide 77218A 18.REMOVE NO. 3 FUEL TANK FILLER PIPE SUPPORT

a.
A459644


Hide 77277R 19.REMOVE FUEL TANK FILLER PIPE PROTECTOR

a.
A458633