Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A0A13  High Voltage System Interlock Circuit Open  P0A0A92  High Voltage System Interlock Performance or Incorrect Operation  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU detects that a safety device (interlock) is operated or that there is an open circuit in the detection circuit. (Even if an open circuit occurs while the vehicle is stopped, the system determines that the safety device was operated.)

The cause of this malfunction may be one of the following:

Detection switch system malfunction
·

Service plug malfunction

·

Rear hybrid motor control inverter assembly malfunction (for AWD)


Low-voltage system malfunction
·

Hybrid vehicle control ECU malfunction

·

Rear hybrid motor control inverter assembly malfunction (for AWD)

·

Service plug malfunction

·

Wire harness malfunction

·

Connector malfunction



INSPECTION DESCRIPTION


A368832E20
1.208,3.333 1.823,3.531 0.615,0.198 10 false : *b 3.365,1.219 3.656,1.438 0.292,0.219 10 false *a 5,2.031 5.292,2.25 0.292,0.219 10 false *a 5.031,3.083 6.833,3.323 1.802,0.24 10 false Hybrid Vehicle Control ECU 2.104,2.125 4.406,2.344 2.302,0.219 10 false Service Plug Grip (Interlock Switch) 0.177,0.135 1.25,0.333 1.073,0.198 12 false for 2WD:

A378539E14
1.219,3.354 1.531,3.552 0.313,0.198 10 false : *b 1.635,1.229 1.948,1.427 0.313,0.198 10 false *a 2.885,1.24 3.198,1.438 0.313,0.198 10 false *a 4.771,1.24 5.083,1.438 0.313,0.198 10 false *a 5.427,2.021 5.74,2.219 0.313,0.198 10 false *a 3.792,2.031 4.104,2.229 0.313,0.198 10 false *a 3.979,2.135 5.354,2.583 1.375,0.448 10 false Service Plug Grip (Interlock Switch) 5.281,3.052 7.125,3.354 1.844,0.302 10 false Hybrid Vehicle Control ECU 0.635,2.771 3.594,2.969 2.958,0.198 10 false Rear Hybrid Motor Control Inverter Assembly 2.24,1.948 3.344,2.333 1.104,0.385 10 false HV Battery Pack Wire 1,1.948 2.031,2.396 1.031,0.448 10 false Inverter Terminal Cover 0.125,0.104 1.125,0.333 1,0.229 12 false for AWD: 0.302,1.302 0.615,1.5 0.313,0.198 10 false *a

System Diagram Location Inspection Content Reason
*a
·

Check whether the safety device (interlock) is connected securely and installed properly (service plug grip, inverter terminal cover*, etc.) and HV battery pack wire*, etc.

·

Check the connection condition of the hybrid vehicle control ECU and rear hybrid motor control inverter assembly* connector.


DTC output due to improper connection or forgetting to install parts.
*b Inspect the detection circuit. DTC output due to an open circuit or improper connection (dirt, foreign matter, etc.).

*: for AWD


DESCRIPTION

When the hybrid vehicle control ECU detects that a safety device (interlock) is operated (such as removal of the service plug grip, inverter cover, inverter terminal cover (for AWD) or HV battery pack wire (for AWD)), it will prohibit hybrid system operation or shut off the system main relays. The safety devices are located as follows: 1 in the service plug grip, 1 on the inverter cover for the terminals of the hybrid motor control inverter assembly motor cable, 1 on the inverter terminal cover for the terminals of the rear motor cable, hybrid underfloor wire and HV battery pack wire of the rear hybrid motor control inverter assembly (for AWD), and 1 on the HV battery pack wire that connects to the rear hybrid motor control inverter assembly (for AWD). If the service plug grip, inverter cover, inverter terminal cover (for AWD) or HV battery pack wire is removed, the interlock signal line will be open. However, if the vehicle is being driven, this condition will be determined to be an open circuit and the system main relays will not be shut off. When the safety devices are re-installed correctly, the system will return to normal when the ignition switch is turned to ON.

The system main relay will be turned off from the next trip after the open is detected until the condition returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0A0A13 High Voltage System Interlock Circuit Open Interlock signal line opens while the vehicle is being driven (at 5 km/h (3 mph) or more)
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Service plug grip

·

Rear hybrid motor control inverter assembly*

·

HV battery pack wire*

·

Inverter terminal cover*


Does not come on Master Warning: Comes on Hybrid Control A
P0A0A92 High Voltage System Interlock Performance or Incorrect Operation Either of the following conditions is met:
·

With the vehicle stopped, the service plug grip with a safety device was removed.

·

With the vehicle stopped, the interlock signal line became open.


(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Service plug grip

·

Rear hybrid motor control inverter assembly*

·

HV battery pack wire*

·

Inverter terminal cover*


Does not come on Master Warning: Comes on Hybrid Control A

*: for AWD


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

With ignition switch ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A394806E06
2.26,2.198 4.563,2.49 2.302,0.292 10 false Service Plug Grip (Interlock Switch) 2.26,2.042 2.792,2.25 0.531,0.208 10 false O72 2.771,1.563 3.302,1.771 0.531,0.208 10 false GND 3.542,1.563 4.073,1.771 0.531,0.208 10 false ILK 3.906,1.563 4.438,1.771 0.531,0.208 10 false 1 2.573,1.563 3.104,1.771 0.531,0.208 10 false 2 5.24,1.563 5.771,1.771 0.531,0.208 10 false ILK 4.938,1.552 5.177,1.719 0.24,0.167 10 false 32 5.906,0.917 6.438,1.125 0.531,0.208 10 false +B 4.781,3.208 7.083,3.5 2.302,0.292 10 false Hybrid Vehicle Control ECU 4.781,3.042 5.167,3.24 0.385,0.198 10 false H44 0.167,0.104 1.635,0.344 1.469,0.24 12 false for 2WD:

A435999E13
0.5,2.927 3.583,3.146 3.083,0.219 10 false Rear Hybrid Motor Control Inverter Assembly 4.25,2.188 5.365,2.625 1.115,0.438 10 false Service Plug Grip (Interlock Switch) 5.313,3.156 7.063,3.51 1.75,0.354 10 false Hybrid Vehicle Control ECU 1.26,1.865 2.271,2.292 1.01,0.427 10 false Inverter Terminal Cover 2.521,1.844 3.219,2.354 0.698,0.51 10 false HV Battery Pack Wire 5.313,2.99 5.625,3.188 0.313,0.198 10 false H44 5.594,1.573 5.906,1.771 0.313,0.198 10 false 32 5.833,1.573 6.146,1.771 0.313,0.198 10 false ILK 5.24,1.604 5.552,1.802 0.313,0.198 10 false 1 4.135,1.604 4.448,1.802 0.313,0.198 10 false 2 4.958,1.604 5.271,1.802 0.313,0.198 10 false ILK 4.292,1.604 4.604,1.802 0.313,0.198 10 false GND 3.573,1.542 3.885,1.74 0.313,0.198 10 false ILKI 3.917,1.604 4.229,1.802 0.313,0.198 10 false 3 0.49,2.771 0.802,2.969 0.313,0.198 10 false O74 0.167,0.167 1.198,0.396 1.031,0.229 12 false for AWD: 6.448,0.865 6.76,1.063 0.313,0.198 10 false +B 4.26,2.01 4.573,2.208 0.313,0.198 10 false O72 0.594,1.594 1,1.76 0.406,0.167 10 false GNR1 0.427,1.604 0.625,1.781 0.198,0.177 10 false 1 0.417,2.042 0.615,2.219 0.198,0.177 10 false 7 0.583,2.042 0.99,2.208 0.406,0.167 10 false GNR2

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery



·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A357589C58
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

·

As interlock circuit DTCs or other DTCs may be stored when the ignition switch to ON in the following procedure, make sure to clear the DTCs after inspection.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0A0A13 or P0A0A92 is output and DTCs other than the DTCs in the table below are output A
P0A0A13 or P0A0A92 is output and any DTCs in the table below are output B
Only P0A0A13 or P0A0A92 is output C


Malfunction Content Relevant DTC
Microcomputer malfunction P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P060B71 Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck
P060B1C Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range
P1CE349 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure
P1CE371 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck
P1CE31C Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range
P060A45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
P060A44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
P060A29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
P060A49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
Power source circuit malfunction P06881F ECM/PCM Power Relay Sense Circuit Intermittent
System malfunction P1C9E9F Hybrid/EV System Reset Stuck Off

HINT:
·

P0A0A13 or P0A0A92 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CLEAR DTC

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397

Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0A0A13 or P0A0A92 is output A
P0A0A13 and P0A0A92 are not output B



Post-procedure1

a.

Turn the ignition switch off.



A

4.CHECK SERVICE PLUG GRIP

B

15.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)
4.CHECK SERVICE PLUG GRIP
CAUTION:

Be sure to wear insulated gloves.


a.
A365595C03
0.104,0.094 0.417,0.25 0.313,0.156 10 false *1
*1 Service Plug Grip


Check if the service plug grip is installed correctly.

NOTICE:

Insert the service plug grip until a click sound is heard.


HINT:
·

For the removal and installation procedures.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL

·

P0A0A92 is also set if the ignition switch is turned to ON with the service plug grip removed. Confirm the conditions when the malfunction occurred.




Result:
Proceed to
OK
NG



OK

5.CHECK VEHICLE CONDITION

NG

INSTALL PARTS CORRECTLY

5.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 2WD A
for AWD B



A

6.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CONNECTOR)

B

16.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CONNECTOR)
6.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
A458479C01
2.26,1.229 2.438,1.417 0.177,0.188 10 true *1
*1 Interlock Connector


Check that the interlock connector at the service plug grip installation socket is connected correctly.

OK:

The connector is connected correctly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the HV battery upper cover panel.



OK

7.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

INSTALL PARTS CORRECTLY

7.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

8.CHECK HYBRID VEHICLE CONTROL ECU

NG

CONNECT SECURELY

8.CHECK HYBRID VEHICLE CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the O72 service plug grip (interlock switch) connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.
A458564C01
0.844,3.479 1.25,3.76 0.406,0.281 2.115,4.042 1.833,3.688 true 0.656,2.667 0.969,2.865 0.313,0.198 10 false *a 2.146,4.073 2.604,4.271 0.458,0.198 10 false ILK 0.938,3.552 1.396,3.75 0.458,0.198 10 false O72
*a Rear view of wire harness connector
(to Service Plug Grip (Interlock Switch))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(O72)Location & Routing

Click Connector(O72)Body>Floor Wire>Inter Lock Switch

O72-1 (ILK) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the O72 service plug grip (interlock switch) connector.


d.

Install the HV battery upper cover panel.



OK

9.CHECK SERVICE PLUG GRIP

NG

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SERVICE PLUG GRIP)
9.CHECK SERVICE PLUG GRIP
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Procedure1

a.
A365596C03
0.115,0.083 0.427,0.24 0.313,0.156 10 false *1
*1 Service Plug Grip


Check the condition of the service plug grip interlock.

OK:

Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

10.CHECK VEHICLE CONDITION

NG

10.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 2WD A
for AWD B



A

11.CHECK HARNESS AND CONNECTOR (SERVICE PLUG GRIP - BODY GROUND)

B

13.CHECK HARNESS AND CONNECTOR (SERVICE PLUG GRIP - BODY GROUND)
11.CHECK HARNESS AND CONNECTOR (SERVICE PLUG GRIP - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the O72 service plug grip (interlock switch) connector.


Procedure1

a.
A458564C02
0.771,3.365 1.208,3.688 0.438,0.323 1.188,4.094 1.604,3.677 true 0.771,2.688 1.083,2.885 0.313,0.198 10 false *a 0.875,3.458 1.333,3.656 0.458,0.198 10 false O72 0.875,4.073 1.333,4.271 0.458,0.198 10 false GND
*a Rear view of wire harness connector
(to Service Plug Grip (Interlock Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O72)Location & Routing

Click Connector(O72)Body>Floor Wire>Inter Lock Switch

O72-2 (GND) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O72 service plug grip (interlock switch) connector.


b.

Install the HV battery upper cover panel.



OK

15.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SERVICE PLUG GRIP)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the H44 hybrid vehicle control ECU connector.


c.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



d.

Disconnect the O72 service plug grip (interlock switch) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458565C01
1.76,1 2.208,1.271 0.448,0.271 4.25,2.771 4.656,3.073 0.406,0.302 5.146,3.063 5.615,3.344 true 1.698,2.281 1.333,2.885 true 0.625,0.781 0.938,0.938 0.313,0.156 10 false *a 4.208,2.25 4.521,2.406 0.313,0.156 10 false *b 1.885,1.073 2.323,1.427 0.438,0.354 10 false H44 4.333,2.854 4.646,3.01 0.313,0.156 10 false O72 5.667,3.375 6.219,3.604 0.552,0.229 10 false ILK 1.167,2.917 1.479,3.073 0.313,0.156 10 false ILK
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to Service Plug Grip (Interlock Switch))


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H44,O72)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

Click Connector(O72)Body>Floor Wire>Inter Lock Switch

H44-32 (ILK) - O72-1 (ILK) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O72 service plug grip (interlock switch) connector.


b.

Install the HV battery upper cover panel.


c.

Reconnect the H44 hybrid vehicle control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (SERVICE PLUG GRIP - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the O72 service plug grip (interlock switch) connector.


Procedure1

a.
A458564C02
0.771,3.365 1.208,3.688 0.438,0.323 1.188,4.094 1.604,3.677 true 0.771,2.688 1.083,2.885 0.313,0.198 10 false *a 0.875,3.458 1.333,3.656 0.458,0.198 10 false O72 0.875,4.073 1.333,4.271 0.458,0.198 10 false GND
*a Rear view of wire harness connector
(to Service Plug Grip (Interlock Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O72)Location & Routing

Click Connector(O72)Body>Floor Wire>Inter Lock Switch

O72-2 (GND) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O72 service plug grip (interlock switch) connector.


b.

Install the HV battery upper cover panel.



OK

14.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY - BODY GROUND)

NG

20.CHECK INVERTER TERMINAL COVER
14.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the O74 rear hybrid motor control inverter assembly connector.


Procedure1

a.
A376643C34
0.313,1 0.719,1.26 0.406,0.26 1.271,1.01 1.042,0.573 true 1,1.667 1.271,1.219 true 0.104,0.146 0.417,0.302 0.313,0.156 10 false *a 0.406,1.063 0.75,1.229 0.344,0.167 10 false O74 0.875,0.417 1.313,0.615 0.438,0.198 10 false GNR1 0.833,1.698 1.271,1.896 0.438,0.198 10 false GNR2
*a Front View of Wire Harness Connector
(to Rear Hybrid Motor Control Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O74)Location & Routing

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O74-1 (GNR1) - Body ground Ignition switch off Below 1 Ω
O74-7 (GNR2) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O74 rear hybrid motor control inverter assembly connector.



OK

15.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)
a.

Check the connections of each connector.

OK:

Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CONNECTOR

16.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
A458479C01
2.26,1.229 2.438,1.417 0.177,0.188 10 true *1
*1 Interlock Connector


Check that the interlock connector at the service plug grip installation socket is connected correctly.

OK:

The connector is connected correctly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the HV battery upper cover panel.



OK

17.CHECK CONNECTOR CONNECTION CONDITION (INVERTER TERMINAL COVER)

NG

INSTALL PARTS CORRECTLY

17.CHECK CONNECTOR CONNECTION CONDITION (INVERTER TERMINAL COVER)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A475631

Check if the inverter terminal cover from the rear hybrid motor control inverter assembly is installed correctly.

OK:

The inverter terminal cover is installed correctly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

18.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY PACK WIRE)

NG

CONNECT SECURELY

18.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY PACK WIRE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A475631

Remove the inverter terminal cover from the rear hybrid motor control inverter assembly.


Procedure1

a.
A475624

Check if the HV battery pack wire is installed correctly.

OK:

The HV battery pack wire is installed correctly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the inverter terminal cover from the rear hybrid motor control inverter assembly.



OK

19.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

19.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>P0A4516

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

7.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK INVERTER TERMINAL COVER
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A475631

Remove the inverter terminal cover from the rear hybrid motor control inverter assembly.


Procedure1

a.
A458523C01
0.125,0.115 0.438,0.271 0.313,0.156 10 false *1
*1 Inverter Terminal Cover


Check the condition of the inverter terminal cover interlock.

OK:

Dirt or foreign matter has not entered the connectors and there is no evidence of contamination.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the inverter terminal cover from the rear hybrid motor control inverter assembly.



OK

21.CHECK HV BATTERY PACK WIRE

NG

21.CHECK HV BATTERY PACK WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A475631

Remove the inverter terminal cover from the rear hybrid motor control inverter assembly.


c.
A475624

Disconnect the HV battery pack wire from the rear hybrid motor control inverter assembly.


Procedure1

a.
A209511C02
0.083,0.073 0.396,0.229 0.313,0.156 10 false *1
*1 Rear Hybrid Motor Control Inverter Assembly


Check the condition of the HV battery pack wire interlock.

OK:

Dirt or foreign matter has not entered the connectors and there is no evidence of contamination.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the HV battery pack wire from the rear hybrid motor control inverter assembly.


b.

Install the inverter terminal cover from the rear hybrid motor control inverter assembly.



OK

22.CHECK HARNESS AND CONNECTOR (SERVICE PLUG GRIP - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

NG

22.CHECK HARNESS AND CONNECTOR (SERVICE PLUG GRIP - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the O72 service plug grip (interlock switch) connector.


c.

Disconnect the O74 rear hybrid motor control inverter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458524C02
0.792,2.75 1.219,3.052 0.427,0.302 5.146,1 5.573,1.302 0.427,0.302 1.51,3.052 1.292,3.396 true 5.156,1.969 4.802,2.688 true 0.833,2.24 1.146,2.396 0.313,0.156 10 false *a 4.063,0.948 4.375,1.104 0.313,0.156 10 false *b 1.083,3.417 1.469,3.583 0.385,0.167 10 false GND 4.698,2.74 5.146,2.938 0.448,0.198 10 false ILKI 5.25,1.094 5.635,1.26 0.385,0.167 10 false O74 0.896,2.833 1.281,3 0.385,0.167 10 false O72
*a Rear view of wire harness connector
(to Service Plug Grip (Interlock Switch))
*b Front View of Wire Harness Connector
(to Rear Hybrid Motor Control Inverter Assembly)


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O72,O74)Location & Routing

Click Connector(O72)Body>Floor Wire>Inter Lock Switch

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O72-2 (GND) - O74-3 (ILKI) Power switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O74 rear hybrid motor control inverter assembly connector.


b.

Reconnect the O72 service plug grip (interlock switch) connector.



OK

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR