Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0441241 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P077514  Pressure Control Solenoid "B" Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P077512.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P077512

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority Note
P077514 Pressure Control Solenoid "B" Circuit Short to Ground or Open An open or short to ground is detected in the shift solenoid valve SL2 circuit for 1 second or more (1-trip detection logic).
·

Transmission valve body assembly (Shift solenoid valve SL2)

·

Transmission wire

·

Harness and connector

·

TCM


Comes on DTC stored Transmission A SAE Code:
P0966

MONITOR DESCRIPTION

This DTC indicates an open or short to ground in the shift solenoid valve SL2 circuit. If there is an open or short to ground in the shift solenoid valve SL2 circuit, the TCM detects the malfunction, illuminates the MIL and stores this DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Start the engine.

4.

Perform the D Position Test inspection in Road Test.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

5.

Stop the vehicle.

6.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

7.

Input the DTC: P077514.

8.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL2)

Pre-procedure1

a.
C397724C27
0.229,1.042 0.688,1.292 0.458,0.25 1.875,1.083 0.708,0.667 true 1.875,1.333 0.708,1.75 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.385,1.667 1,1.865 0.615,0.198 10 false SL2- 0.354,0.583 0.969,0.781 0.615,0.198 10 false SL2+ 0.365,1.104 0.698,1.281 0.333,0.177 10 false D74
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D74)Location & Routing

Click Connector(D74)Engine Compartment>Engine Wire>Transmission Wire

D74-3 (SL2+) - D74-8 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
D74-3 (SL2+) - Body ground and other terminals Always 10 kΩ or higher
D74-8 (SL2-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the transmission wire connector.



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

4.INSPECT TRANSMISSION WIRE
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

Pre-procedure1

a.

Disconnect the TCM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D71)Location & Routing

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D71-19 (SL2+) - D71-20 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
D71-19 (SL2+) - Body ground and other terminals Always 10 kΩ or higher
D71-20 (SL2-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the TCM connector.



OK

3.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - TCM)

3.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.INSPECT TRANSMISSION WIRE

Pre-procedure1

a.

Disconnect the transmission wire connector.

C397729C02
4.49,2.677 4.885,2.938 0.396,0.26 3,1.531 3.75,1.531 true 5.448,1.313 5.698,0.896 true 6.229,1.313 5.979,0.896 true 5.865,2.698 6.531,2.281 true 5.833,2.896 6.5,3.146 true 1.104,0.177 1.417,0.333 0.313,0.156 10 false *1 3.792,1.448 4.104,1.604 0.313,0.156 10 false *2 4.854,0.198 5.167,0.354 0.313,0.156 10 false *3 5.75,0.208 6.063,0.365 0.313,0.156 10 false *a 5.771,1.854 6.083,2.01 0.313,0.156 10 false *b 5.344,1.24 5.656,1.396 0.313,0.156 10 false 1 6.271,1.25 6.583,1.406 0.313,0.156 10 false 2 6.573,2.198 6.969,2.469 0.396,0.271 10 false SL2+ 6.552,3.073 6.948,3.344 0.396,0.271 10 false SL2- 4.583,2.75 4.885,2.948 0.302,0.198 10 false D74
*1 Transmission Valve Body Assembly *2 Shift Solenoid Valve SL2
*3 Transmission Wire - -
*a Shift Solenoid Valve Side *b Wire Harness Connector Side



b.

Disconnect the transmission wire connector from the shift solenoid valve SL2.

HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (shift solenoid valve side) - 3 (SL2+) (wire harness connector side) Always Below 1 Ω
2 (shift solenoid valve side) - 8 (SL2-) (wire harness connector side) Always Below 1 Ω
1 (shift solenoid valve side) or 3 (SL2+) (wire harness connector side) - All other terminals Always 10 kΩ or higher
2 (shift solenoid valve side) or 8 (SL2-) (wire harness connector side) - All other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

5.REPLACE TRANSMISSION VALVE BODY ASSEMBLY

NG

5.REPLACE TRANSMISSION VALVE BODY ASSEMBLY
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT