Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0441241 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P274512  Intermediate Shaft Speed Sensor "B" Circuit Short to Battery  P274514  Intermediate Shaft Speed Sensor "B" Circuit Short to Ground or Open  P274531  Intermediate Shaft Speed Sensor "B" No Signal  


DESCRIPTION

The transmission revolution sensor (NC1) detects the intermediate shaft (C1 clutch) speed and sends it to the TCM.

The TCM determines if gear mode should be entered by comparing the transmission revolution sensor (NT) and (NC1) signals.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority Note
P274512 Intermediate Shaft Speed Sensor "B" Circuit Short to Battery The transmission revolution sensor (NC1) signal is normal but the transmission revolution sensor (NC1) output voltage is higher than 1.8 V for 4.5 seconds or more (1-trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NC1)

·

TCM

·

Transmission wire


Comes on DTC stored Transmission A SAE Code:
P07C8
P274514 Intermediate Shaft Speed Sensor "B" Circuit Short to Ground or Open The transmission revolution sensor (NC1) signal is normal but the transmission revolution sensor (NC1) output voltage is less than 0.2 V for 4.5 seconds or more (1-trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NC1)

·

TCM

·

Transmission wire


Comes on DTC stored Transmission A SAE Code:
P07C7
P274531 Intermediate Shaft Speed Sensor "B" No Signal When the transmission revolution sensor (NOUT) signal indicates 300 rpm or more and the SPD signal indicates 10 km/h (6 mph) or more, transmission revolution sensor (NC1) signal indicates less than 300 rpm for 5 seconds or more. (1-trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NC1)

·

TCM

·

Transmission wire


Comes on DTC stored Transmission A SAE Code:
P2747

MONITOR DESCRIPTION

The TCM receives signals from the transmission revolution sensor (NC1) installed to the continuously variable transaxle and determines the intermediate shaft (C1 clutch) speed.

If the TCM detects no signal from the transmission revolution sensor (NC1) even while the vehicle is being driven, it will determine that the transmission revolution sensor (NC1) is malfunctioning, illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Start the engine.

4.

Perform the D Position Test inspection in Road Test.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

5.

Stop the vehicle.

6.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

7.

Input the DTC: P274512, P274514 or P274531.

8.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C359198E13
5.719,0.833 6.177,1.031 0.458,0.198 10 false NC1B 5.729,2.063 6.188,2.26 0.458,0.198 10 false NC1O 5.708,2.521 6.167,2.719 0.458,0.198 10 false E1 5.51,2.396 5.969,2.594 0.458,0.198 10 false 2 5.51,2.063 5.969,2.26 0.458,0.198 10 false 8 3.146,0.844 3.604,1.042 0.458,0.198 10 false NC1B 6.344,0.677 6.802,0.875 0.458,0.198 10 false 12 V 3.135,2.063 3.594,2.26 0.458,0.198 10 false NC1O 3.656,0.833 4.115,1.031 0.458,0.198 10 false 16 3.656,2.063 4.115,2.26 0.458,0.198 10 false 17 5.448,0.833 5.906,1.031 0.458,0.198 10 false 24 2.469,0.844 2.927,1.042 0.458,0.198 10 false 1 2.49,2.052 2.948,2.25 0.458,0.198 10 false 2 2.417,2.521 2.875,2.719 0.458,0.198 10 false D74 2.417,2.688 3.583,2.917 1.167,0.229 10 false Transmission Wire 0.406,2.344 1.917,2.792 1.51,0.448 10 false Transmission Revolution Sensor (NC1) 0.635,3.135 3.427,3.615 2.792,0.479 10 false Continuously Variable Transaxle Assembly 6.01,2.885 6.625,3.083 0.615,0.198 10 false D71 6.01,3.042 6.625,3.24 0.615,0.198 10 false TCM

CAUTION / NOTICE / HINT

CAUTION:
·
A371909

Strictly observe posted speed limits, traffic laws and road conditions.

·

Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.

·

Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.


·
A356953

Do not operate the GTS while driving the vehicle.

·

Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.



NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (NC1 SENSOR VOLTAGE)
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NC1 Sensor Voltage Transmission revolution sensor (NC1) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) -
Powertrain > Transmission > Data List
Tester Display
NC1 Sensor Voltage
50003 373 541
Result:
Result Proceed to
The value of NC1 Sensor Voltage is between 0.2 and 1.8 V A
None of the above conditions are met B




A

2.READ VALUE USING GTS (NC1 SENSOR SPEED)

B

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
2.READ VALUE USING GTS (NC1 SENSOR SPEED)
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NC1 Sensor Speed Intermediate shaft (C1 clutch) speed (NC1) Min.: 0 rpm
Max.: 65535 rpm
0 rpm: Vehicle stopped and synchronizer engaged -
Status of Synchronize Synchronizer status OFF or ON
·

OFF: Synchronizer not engaged

·

ON: Synchronizer engaged


-
Powertrain > Transmission > Data List
Tester Display
NC1 Sensor Speed
Status of Synchronize
50003 373 540,934
Result:
Result Proceed to
The value of NC1 Sensor Speed is 0 rpm A
None of the above conditions are met B




A

3.READ VALUE USING GTS (NC1 SENSOR SPEED)

B

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
3.READ VALUE USING GTS (NC1 SENSOR SPEED)
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NT Sensor Speed Input turbine speed (NT) Min.: 0 rpm
Max.: 65535 rpm
·

Equal to engine speed (NE): Lock-up ON (After warming up engine)

·

Nearly equal to engine speed (NE): Lock-up OFF (Engine idling with shift lever in P or N)


-
NC1 Sensor Speed Intermediate shaft (C1 clutch) speed (NC1) Min.: 0 rpm
Max.: 65535 rpm
Equal to NT Sensor Speed: Vehicle being driven in gear mode -
Shift Mode Shift mode status Gear Mode or Belt Mode - -
Powertrain > Transmission > Data List
Tester Display
NT Sensor Speed
NC1 Sensor Speed
50003 373 929,540
Result:
Result Proceed to
The value of NT Sensor Speed and NC1 Sensor Speed are the same A
The value of NT Sensor Speed and NC1 Sensor Speed are different B




A

4.REPLACE TCM

B

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
4.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

Pre-procedure1

a.

Disconnect the transmission wire connector.


b.

Disconnect the TCM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D74,D71)Location & Routing

Click Connector(D74)Engine Compartment>Engine Wire>Transmission Wire

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D74-16 (NC1B) - D71-24 (NC1B) Always Below 1 Ω
D74-17 (NC1O) - D71-8 (NC1O) Always Below 1 Ω
D71-2 (E1) - Body ground Always Below 1 Ω
D74-16 (NC1B) or D71-24 (NC1B) - Body ground and other terminals Always 10 kΩ or higher
D74-17 (NC1O) or D71-8 (NC1O) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the TCM connector.


b.

Connect the transmission wire connector.



OK

6.CHECK TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - TCM)

6.CHECK TCM

Pre-procedure1

a.

Disconnect the transmission wire connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D74)Location & Routing

Click Connector(D74)Engine Compartment>Engine Wire>Transmission Wire

D74-16 (NC1B) - Body ground Ignition switch ON 11 to 14 V



Post-procedure1

a.

Turn the ignition switch off.


b.

Connect the transmission wire connector.


Pre-procedure2

a.

Disconnect the TCM connector.

C397733C05
0.396,1.156 0.813,1.438 0.417,0.281 5.542,0.25 4.969,1.198 true 3.094,0.208 3.76,1.167 true 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 5.604,0.177 5.917,0.375 0.313,0.198 10 false E1 2.688,0.146 3.302,0.344 0.615,0.198 10 false NC1O 0.5,1.24 0.813,1.448 0.313,0.208 10 false D71
*a Component without harness connected
(TCM)
- -



Procedure2

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D71)Location & Routing

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D71-8 (NC1O) - D71-2 (E1) Always 99 to 101 Ω


Result:
Proceed to
OK
NG



Post-procedure2

a.

Connect the TCM connector.



OK

7.INSPECT TRANSMISSION WIRE

NG

8.REPLACE TCM
7.INSPECT TRANSMISSION WIRE

Pre-procedure1

a.

Disconnect the transmission wire connector.


b.
C398926C02
2.375,2.583 2.781,2.833 0.406,0.25 1.021,0.719 1.604,1.052 true 1.031,1.667 1.615,1.333 true 2.01,3.875 2.594,3.542 true 1.833,3.938 2.583,4.271 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *1 1.667,0.26 1.979,0.417 0.313,0.156 10 false *a 1.604,2.26 1.917,2.417 0.313,0.156 10 false *b 2.635,3.458 3.25,3.656 0.615,0.198 10 false NC1B 2.635,4.198 3.25,4.396 0.615,0.198 10 false NC1O 0.917,0.635 1.531,0.833 0.615,0.198 10 false 1 0.906,1.594 1.521,1.792 0.615,0.198 10 false 2 2.469,2.646 2.792,2.833 0.323,0.188 10 false D74
*1 Transmission Wire
*a Transmission Revolution Sensor Side
*b Wire Harness Connector Side


Disconnect the transmission wire connector from the transmission revolution sensor (NC1).

HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>REVOLUTION SENSOR (NC1 SENSOR)>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (transmission revolution sensor side) - 16 (NC1B) (wire harness connector side) Always Below 1 Ω
2 (transmission revolution sensor side) - 17 (NC1O) (wire harness connector side) Always Below 1 Ω
1 (transmission revolution sensor side) or 16 (NC1B) (wire harness connector side) - All other terminals Always 10 kΩ or higher
2 (transmission revolution sensor side) or 17 (NC1O) (wire harness connector side) - All other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE TRANSMISSION REVOLUTION SENSOR (NC1)

NG

8.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT