Using the current from the TCM, the shift solenoid valve SLU controls the lock-up clutch pressure, and performs lock-up and flex lock-up control.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|---|
| P275612 | Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery | A short to +B is detected in the shift solenoid valve SLU circuit for 1 second or more (1-trip detection logic). | ·
Transmission valve body assembly (Shift solenoid valve SLU) ·
Transmission wire ·
Harness and connector ·
TCM |
Comes on | DTC stored | Transmission | A | SAE Code:
P2763 |
This DTC indicates a short to +B in the shift solenoid valve SLU circuit. If there is a short to +B in the shift solenoid valve SLU circuit, the TCM detects the malfunction, illuminates the MIL and stores this DTC.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Drive the vehicle and confirm the lock-up on and off conditions according to Road Test.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P275612.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Pre-procedure1
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the transmission wire connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D74)Location & Routingewd_type=routing;type=c;code=D74 Click Connector(D74)Engine Compartment>Engine Wire>Transmission Wireewd_type=component;type=c;code=D74;pinno=4,9 |
||
| D74-4 (SLU+) - Other terminals | Always | 10 kΩ or higher |
| D74-9 (SLU-) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the transmission wire connector.
OK
NG
Pre-procedure1
Disconnect the TCM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D71)Location & Routingewd_type=routing;type=c;code=D71 Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECUewd_type=component;type=c;code=D71;pinno=6,5 |
||
| D71-6 (SLU+) - Other terminals | Always | 10 kΩ or higher |
| D71-5 (SLU-) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the TCM connector.
OK
NG
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Pre-procedure1
Disconnect the transmission wire connector.
| *1 | Transmission Valve Body Assembly | *2 | Shift Solenoid Valve SLU |
| *3 | Transmission Wire | - | - |
| *a | Shift Solenoid Valve Side | *b | Wire Harness Connector Side |
Disconnect the transmission wire connector from the shift solenoid valve SLU.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (shift solenoid valve side) or 4 (SLU+) (wire harness connector side) - All other terminals | Always | 10 kΩ or higher |
| 2 (shift solenoid valve side) or 9 (SLU-) (wire harness connector side) - All other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION