If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 2 speaker assembly (w/ Telematics Transceiver) | A |
| Front No. 1 speaker assembly or front No. 2 speaker assembly (w/o Telematics Transceiver) | B |
| Rear speaker assembly | C |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the H84 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H83,H84)Location & Routingewd_type=routing;type=c,c;code=H83,H84 Click Connector(H83)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H83;pinno=2,7 Click Connector(H84)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H84;pinno=1,2 |
||
| H83-2 (FL+) - H84-1 (SPI+) | Always | Below 1 Ω |
| H83-7 (FL-) - H84-2 (SPI-) | Always | Below 1 Ω |
| H83-2 (FL+) or H84-1 (SPI+) - Body ground | Always | 10 kΩ or higher |
| H83-7 (FL-) or H84-2 (SPI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H84 telematics transceiver connector.
Disconnect the H87 front No. 2 speaker assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H84,H87)Location & Routingewd_type=routing;type=c,c;code=H84,H87 Click Connector(H84)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H84;pinno=3,4 Click Connector(H87)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=H87;pinno=3,1 |
||
| H84-3 (SPO+) - H87-3 (+) | Always | Below 1 Ω |
| H84-4 (SPO-) - H87-1 (-) | Always | Below 1 Ω |
| H84-3 (SPO+) or H87-3 (+) - Body ground | Always | 10 kΩ or higher |
| H84-4 (SPO-) or H87-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telematics transceiver.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| *a | Component without harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H84)Location & Routingewd_type=routing;type=c;code=H84 Click Connector(H84)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H84;pinno=1,3,2,4 |
||
| H84-1 (SPI+) - H84-3 (SPO+) | Always | Below 1 Ω |
| H84-2 (SPI-) - H84-4 (SPO-) | Always | Below 1 Ω |
| H84-1 (SPI+) - H84-2 (SPI-) | Always | 10 kΩ or higher |
| H84-3 (SPO+) - H84-4 (SPO-) | Always | 10 kΩ or higher |
| H84-1 (SPI+) or H84-3 (SPO+) - Body ground | Always | 10 kΩ or higher |
| H84-2 (SPI-) or H84-4 (SPO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the H88 front No. 2 speaker assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H83,H88)Location & Routingewd_type=routing;type=c,c;code=H83,H88 Click Connector(H83)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H83;pinno=1,6 Click Connector(H88)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=H88;pinno=3,1 |
||
| H83-1 (FR+) - H88-3 (+) | Always | Below 1 Ω |
| H83-6 (FR-) - H88-1 (-) | Always | Below 1 Ω |
| H83-1 (FR+) or H88-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-6 (FR-) or H88-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H83,H88,H87,K2,L2)Location & Routingewd_type=routing;type=c,c,c,c,c;code=H83,H88,H87,K2,L2 Click Connector(H83)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H83;pinno=1,6,2,7 Click Connector(H88)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=H88;pinno=3,1,4,2 Click Connector(H87)Instrument Panel>Instrument Panel Wire / Speaker Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=H87;pinno=3,1,4,2 Click Connector(K2)Body>Front Door Wire RH / Television Camera Wire>Front No. 1 Speaker Assembly RHewd_type=component;type=c;code=K2;pinno=2,1 Click Connector(L2)Body>Front Door Wire LH / Television Camera Wire>Front No. 1 Speaker Assembly LHewd_type=component;type=c;code=L2;pinno=2,1 |
||
| H83-1 (FR+) - H88-3 (+) | Always | Below 1 Ω |
| H83-6 (FR-) - H88-1 (-) | Always | Below 1 Ω |
| H83-2 (FL+) - H87-3 (+) | Always | Below 1 Ω |
| H83-7 (FL-) - H87-1 (-) | Always | Below 1 Ω |
| H88-4 (TWR+) - K2-2 | Always | Below 1 Ω |
| H88-2 (TWR-) - K2-1 | Always | Below 1 Ω |
| H87-4 (TWL+) - L2-2 | Always | Below 1 Ω |
| H87-2 (TWL-) - L2-1 | Always | Below 1 Ω |
| H83-1 (FR+) or H88-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-6 (FR-) or H88-1 (-) - Body ground | Always | 10 kΩ or higher |
| H83-2 (FL+) or H87-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-7 (FL-) or H87-1 (-) - Body ground | Always | 10 kΩ or higher |
| H88-4 (TWR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H88-2 (TWR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H87-4 (TWL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H87-2 (TWL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the M2 and N2 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H83,M2,N2)Location & Routingewd_type=routing;type=c,c,c;code=H83,M2,N2 Click Connector(H83)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H83;pinno=4,9,3,8 Click Connector(M2)Body>No. 1 Rear Door Wire>Rear Speaker Assembly RHewd_type=component;type=c;code=M2;pinno=2,1 Click Connector(N2)Body>No. 2 Rear Door Wire>Rear Speaker Assembly LHewd_type=component;type=c;code=N2;pinno=2,1 |
||
| H83-4 (RR+) - M2-2 | Always | Below 1 Ω |
| H83-9 (RR-) - M2-1 | Always | Below 1 Ω |
| H83-3 (RL+) - N2-2 | Always | Below 1 Ω |
| H83-8 (RL-) - N2-1 | Always | Below 1 Ω |
| H83-4 (RR+) or M2-2 - Body ground | Always | 10 kΩ or higher |
| H83-9 (RR-) or M2-1 - Body ground | Always | 10 kΩ or higher |
| H83-3 (RL+) or N2-2 - Body ground | Always | 10 kΩ or higher |
| H83-8 (RL-) or N2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE