Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE › 2020.08–2021.07
RM3700E _52 Drivetrain _093736 AXLE AND DIFFERENTIAL _0441823 STEERING KNUCKLE A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C443144N03
6.604,2.292 6.438,2.292 6.438,2.292 6.25,2.865 false 4.604,1.302 4.854,0.802 4.854,0.802 5.021,0.802 false 2.875,0.802 3.094,0.448 3.094,0.448 3.26,0.448 false 2.635,3.031 3.052,3.542 3.052,3.542 3.219,3.542 false 1.083,3.417 1.417,3.417 false 1.417,1.083 1.75,1.083 false 3.313,0.354 3.594,0.708 0.281,0.354 10 false *1 1.635,0.469 1.917,0.823 0.281,0.354 10 false x3 6.906,2.177 7.115,2.531 0.208,0.354 18 false 3 5.052,0.646 5.333,1 0.281,0.354 18 false 4 3.5,3.417 3.781,3.771 0.281,0.354 18 false 2 1.469,3.281 1.75,3.635 0.281,0.354 18 false 1 1.219,1.031 1.5,1.365 0.281,0.333 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT AXLE ASSEMBLY - - - -
2 FRONT LOWER BALL JOINT ASSEMBLY 43340A (Click here) - -
3 FRONT AXLE HUB SUB-ASSEMBLY 43502C (Click here) - -
4 FRONT DISC BRAKE DUST COVER 47782 - - -

*1 STEERING KNUCKLE - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the steering knuckle removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
for HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT AXLE ASSEMBLY

Hide 43340A 2.REMOVE FRONT LOWER BALL JOINT ASSEMBLY

Z101186

Click here(Click here)

Hide 43502C 3.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

a.
C443135N03
0.396,0.073 0.833,0.385 0.438,0.313 18 false i, ii

i.

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



ii.

Using a 12 mm hexagon socket wrench, remove the 3 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not drop the front axle hub sub-assembly.

·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.





Hide 47782 4.REMOVE FRONT DISC BRAKE DUST COVER

a.
C443136