Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093331 M15A-FXE ENGINE MECHANICAL _0440548 ENGINE ASSEMBLY A

M15A-FXE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A477042N02
6.375,0.177 6.875,0.177 false 6.365,0.604 6.865,0.604 false 1.073,0.917 1.573,0.917 false 1.156,3.583 1.656,3.583 false 1.604,4.5 2.104,4.5 false 4.146,5.417 4.479,5.417 false 4.667,3.833 5,3.833 false 6.333,4.5 6.333,4.917 false 5.594,0.063 6.771,0.583 1.177,0.521 18 false 1, 3, 4 1.625,0.75 2.177,1.104 0.552,0.354 18 false 13 1.75,3.427 2.302,3.781 0.552,0.354 18 false 8 4,5.271 4.552,5.625 0.552,0.354 18 false 7 5.083,3.729 5.635,4.083 0.552,0.354 18 false 9 6.25,4.979 6.802,5.333 0.552,0.354 18 false 5 5.229,0.479 6.406,1 1.177,0.521 18 false 2, 10 - 12 1.333,4.333 1.885,4.688 0.552,0.354 18 false 6 5.021,4.417 5.333,4.615 0.313,0.198 10 false x2 4.521,4.667 4.833,4.865 0.313,0.198 10 false x2 0.75,2.833 1.063,3.031 0.313,0.198 10 false x2 5.271,5.333 5.583,5.531 0.313,0.198 10 false x2 3.438,5.135 3.75,5.333 0.313,0.198 10 false x9 2.938,5.385 3.25,5.583 0.313,0.198 10 false x4 2.354,5.135 2.667,5.333 0.313,0.198 10 false x4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 REFRIGERANT FROM REFRIGERATION SYSTEM - - (Click here) -
3 DISCHARGE FUEL SYSTEM PRESSURE - (Click here) - -
4 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - (Click here) - -
5 FRONT WHEELS - - - -
6 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
7 ENGINE UNDER COVER LH 51442C - - -
8 ENGINE UNDER COVER RH 51441C - - -
9 NO. 4 CENTER ENGINE UNDER COVER 51447D - - -
10 DRAIN ENGINE OIL - - (Click here) -
11 DRAIN ENGINE COOLANT - - (Click here) -
12 DRAIN HYBRID TRANSAXLE FLUID - - (Click here) -
13 HYBRID MOTOR CONTROL INVERTER ASSEMBLY G92A0 - - -

A486654N01
4.146,0.313 4.563,0.313 false 3.906,0.969 4.323,0.969 false 2.646,0.76 2.813,0.76 2.813,0.76 3.156,1.01 false 2.594,5.156 3.01,5.156 false 2.417,4.417 2.583,4.583 2.583,4.583 2.75,4.583 false 1.448,3.979 1.583,4.198 1.583,4.198 1.75,4.198 false 0.896,4.469 1.313,4.469 false 0.792,1.208 0.958,1.208 0.958,1.208 1.302,1.531 false 1.615,0.771 1.781,0.771 1.781,0.771 2.104,1.167 false 5.042,5.021 5.208,5.021 5.208,5.021 5.458,4.781 false 5.635,4.802 5.948,5.208 5.948,5.208 6.115,5.208 false 5.958,3.188 6.375,3.188 false 1.177,2.99 1.354,2.792 1.354,2.792 1.521,2.792 false 1.115,5 1.281,5 1.281,5 1.49,4.76 false 0.698,3.26 0.865,3.26 0.865,3.26 1.042,3.542 false 5.969,0.969 6.385,0.969 false 5.896,1.479 6.146,1.333 6.146,1.333 6.313,1.333 false 0.615,3.01 0.781,3.01 0.781,3.01 1.115,3.146 false 1.219,3.542 1.396,3.344 1.396,3.344 1.563,3.344 false 6.531,0.177 6.833,0.177 false 2.177,5.406 2.375,5.406 false 4.615,0.188 5.167,0.542 0.552,0.354 18 false 14 4.396,0.833 4.948,1.188 0.552,0.354 18 false 15 2.344,0.646 2.896,1 0.552,0.354 18 false 15 3.042,5.01 3.594,5.365 0.552,0.354 18 false 16 2.792,4.448 3.344,4.802 0.552,0.354 18 false 17 1.802,4.083 2.354,4.438 0.552,0.354 18 false 18 0.615,4.344 1.167,4.698 0.552,0.354 18 false 19 0.813,4.896 1.365,5.25 0.552,0.354 18 false 20 0.458,1.083 1.01,1.438 0.552,0.354 18 false 21 1.313,0.656 1.865,1.01 0.552,0.354 18 false 22 4.729,4.885 5.281,5.24 0.552,0.354 18 false 23 6.167,5.073 6.719,5.427 0.552,0.354 18 false 24 6.719,3.073 7.083,3.417 0.365,0.344 18 false 25 1.583,2.656 1.948,3 0.365,0.344 18 false 26 0.396,3.135 0.76,3.479 0.365,0.344 18 false 27 6.427,0.833 6.792,1.177 0.365,0.344 18 false 29 6.719,1.229 7.083,1.573 0.365,0.344 18 false 30 1.635,3.25 1.792,3.448 0.156,0.198 10 false ● 0.417,2.906 0.573,3.104 0.156,0.198 10 false ● 3.323,0.49 3.552,0.688 0.229,0.198 10 false x2 6.177,0.031 6.542,0.375 0.365,0.344 18 false 28 2.01,5.333 2.167,5.531 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

14 NO. 1 RELAY BLOCK COVER 82662A - - -
15 ENGINE WIRE - - - -
16 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B - - -
17 NO. 1 RADIATOR HOSE 16571C - - -
18 NO. 2 RADIATOR HOSE 16572D - - -
19 INLET HYBRID RADIATOR HOSE G922H - - -
20 OUTLET NO. 1 HYBRID WATER PUMP HOSE G922F - - -
21 NO. 1 FUEL VAPOR FEED HOSE 23826 - - -
22 FUEL TANK TO CANISTER TUBE 77261D - - -
23 NO. 3 WATER BY-PASS HOSE ASSEMBLY 16290F - - -
24 INLET HEATER WATER HOSE 87245 - - -
25 FUEL TUBE SUB-ASSEMBLY 23901 (Click here) - -
26 NO. 1 COOLER REFRIGERANT DISCHARGE HOSE 88711 - - -
27 SUCTION HOSE SUB-ASSEMBLY 88704 - - -
28 SECURE STEERING WHEEL - (Click here) - -
29 COLUMN HOLE COVER SILENCER SHEET 45259A - - -
30 NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 (Click here) - -

● Non-reusable part - -

A476306N04
0.083,0.083 7.083,5.75 7,5.667 5.5,0.188 6.083,0.188 false 5.417,3.167 6,3.167 false 0.583,4.583 1,4.583 false 0.531,1.583 0.948,1.583 false 1.958,1.885 2.917,0.417 2.917,0.417 3.167,0.417 false 2.115,4.865 3,3.583 3,3.583 3.25,3.583 false 0.083,2.917 7.083,2.917 false 5.854,4.604 6.167,4.802 0.313,0.198 10 false x2 5.99,4.198 6.302,4.396 0.313,0.198 10 false x2 2.167,5.333 2.479,5.531 0.313,0.198 10 false x2 1.927,5.167 2.24,5.365 0.313,0.198 10 false x2 2.49,2.688 2.802,2.885 0.313,0.198 10 false x2 2.156,2.354 2.469,2.552 0.313,0.198 10 false x2 5.833,1.521 6.146,1.719 0.313,0.198 10 false x2 5.99,1.104 6.302,1.302 0.313,0.198 10 false x2 0.313,1.5 0.594,1.854 0.281,0.354 10 false ● 5.292,0.125 5.573,0.479 0.281,0.354 10 false ● 5.219,3.063 5.5,3.417 0.281,0.354 10 false ● 0.385,4.5 0.667,4.854 0.281,0.354 10 false ● 3.604,0.219 4.156,0.573 0.552,0.354 18 false 31 3.604,3.406 4.156,3.76 0.552,0.354 18 false 31 0.167,0.167 0.906,0.635 0.74,0.469 12 false *A 0.167,3 0.906,3.469 0.74,0.469 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

31 FRONT EXHAUST PIPE ASSEMBLY 17410 (Click here) - -

*A for 2WD *B for AWD
● Non-reusable part - -

A459844N04
1.417,2.375 2.083,2.542 0.667,0.167 6.333,1.271 7.031,1.438 0.698,0.167 3.052,0.469 3.333,0.156 3.333,0.156 3.5,0.156 false 5.552,2.427 5.875,2.427 false 0.656,2.656 0.438,3.094 0.438,3.094 0.438,3.26 false 5.302,0.906 5.552,0.635 5.552,0.635 5.719,0.635 false 5.646,3.615 5.969,3.615 false 0.875,0.99 1.198,0.99 false 2.635,4.219 3.021,4.219 false 2.354,2.521 1.875,2.708 1.875,2.708 1.875,2.875 false 2.448,1.729 2.594,1.292 2.594,1.292 2.76,1.292 false 1.729,2.375 1.729,2.229 false 6.104,1.354 6.333,1.354 false 3.573,0.021 4.125,0.375 0.552,0.354 18 false 32 5.281,3.438 5.833,3.792 0.552,0.354 18 false 37 1.896,2.875 2.448,3.229 0.552,0.354 18 false 35 3.115,1.115 3.667,1.469 0.552,0.354 18 false 36 6.104,0.469 6.49,0.813 0.385,0.344 18 false 36 0.438,2.031 0.719,2.24 0.281,0.208 10 false x2 0.656,0.844 0.969,1.042 0.313,0.198 10 false x2 6,1.385 6.313,1.583 0.313,0.198 10 false x2 5.573,4.833 5.885,5.031 0.313,0.198 10 false x2 5.021,5.042 5.333,5.24 0.313,0.198 10 false x2 4.677,5.031 4.99,5.229 0.313,0.198 10 false x2 3.646,4.875 3.958,5.073 0.313,0.198 10 false x2 3.427,5.073 3.74,5.271 0.313,0.198 10 false x2 6.063,1.906 6.375,2.104 0.313,0.198 10 false x2 1.24,0.865 1.625,1.208 0.385,0.344 18 false 38 0.458,3.25 1.01,3.604 0.552,0.354 18 false 39 0.823,0.281 1.104,0.49 0.281,0.208 10 false x2 1.406,1.625 1.688,1.833 0.281,0.208 10 false x2 1.927,2.021 2.208,2.229 0.281,0.208 10 false x2 5.938,3.083 6.25,3.281 0.313,0.198 10 false x3 6.458,2.875 6.771,3.073 0.313,0.198 10 false x4 2.281,4.063 2.833,4.417 0.552,0.354 18 false 34 5.198,2.26 5.75,2.615 0.552,0.354 18 false 33 1.438,2.375 2.417,2.531 0.979,0.156 8 false 43 (438, 32) 6.365,1.271 7.104,1.427 0.74,0.156 8 false 43 (438, 32)

Procedure Part Name Code
Z101186

Z101188

Z101187

32 DRIVE SHAFT ASSEMBLY - - - -
33 ENGINE MOUNTING STAY LH 12318 - - -
34 ENGINE ASSEMBLY WITH TRANSAXLE - (Click here) - -
35 ENGINE MOUNTING BRACKET CAP 12353 (Click here) - -
36 ENGINE HANGER - (Click here) - -
37 ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH 12372A (Click here) - -
38 INVERTER RESERVE TANK ASSEMBLY G92A0A - - -
39 ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH 12305 (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

A479307N01
4.583,0.5 5.167,0.5 false 0.833,1.833 1.167,1.833 false 1.688,3.917 2.021,3.917 false 0.583,4.167 0.917,4.167 false 4.667,2.417 5,2.417 false 5.75,3.417 6.083,3.417 false 5.51,0.26 6.063,0.615 0.552,0.354 18 false 43 4.333,2.313 4.885,2.667 0.552,0.354 18 false 44 6.156,3.26 6.708,3.615 0.552,0.354 18 false 42 2.104,3.771 2.656,4.125 0.552,0.354 18 false 40 0.26,4.021 0.813,4.375 0.552,0.354 18 false 41 0.5,1.719 1.052,2.073 0.552,0.354 18 false 45 0.854,2.781 1.167,2.979 0.313,0.198 10 false x5 0.958,3.51 1.271,3.708 0.313,0.198 10 false x2 6.26,2.26 6.573,2.458 0.313,0.198 10 false x2 2.938,0.229 3.25,0.427 0.313,0.198 10 false x10

Procedure Part Name Code
Z101186

Z101187

Z101188

40 STARTER HOLE INSULATOR 28193 - - -
41 FLYWHEEL HOUSING SIDE COVER 11363A - - -
42 HV AIR CONDITIONIG WIRE 821H2 - - -
43 ENGINE WIRE 82121 (Click here) - -
44 WATER HOSE - - - -
45 ENGINE ASSEMBLY - (Click here) - -

A479309N01
6.365,0.25 6.781,0.25 false 3.646,0.25 4.063,0.25 false 1.583,1 2,1 false 2.344,3 2.76,3 false 4.219,2.167 4.635,2.167 false 5.146,3.333 5.396,3.333 false 4.365,2.917 4.531,2.917 false 5.219,2.823 5.417,2.417 5.417,2.417 5.583,2.417 false 3.333,0.104 3.823,0.417 0.49,0.313 18 false 51 5.979,0.083 6.469,0.396 0.49,0.313 18 false 50 1.26,0.854 1.75,1.167 0.49,0.313 18 false 51 2.833,2.833 3.323,3.146 0.49,0.313 18 false 49 4.75,2.01 5.24,2.323 0.49,0.313 18 false 48 4.094,2.708 4.583,3.021 0.49,0.313 18 false 47 4.813,3.177 5.302,3.49 0.49,0.313 18 false 46 4.646,0.563 4.958,0.76 0.313,0.198 10 false x2 6.25,3.219 6.563,3.417 0.313,0.198 10 false x6 1.354,3.219 1.667,3.417 0.313,0.198 10 false x4 1.417,1.417 1.729,1.615 0.313,0.198 10 false x2 5.281,2.802 5.594,3 0.313,0.198 10 false x8 5.635,2.302 6.094,2.5 0.458,0.198 10 false ● ★

Procedure Part Name Code
Z101186

Z101187

Z101188

46 TRANSMISSION INPUT DAMPER ASSEMBLY 31270 (Click here) - -
47 FLYWHEEL SUB-ASSEMBLY 13405 (Click here) - -
48 NO. 1 CRANKSHAFT POSITION SENSOR PLATE 19315 - - -
49 COMPRESSOR WITH MOTOR ASSEMBLY 88370 - - -
50 ENGINE ASSEMBLY TO ENGINE STAND - (Click here) - -
51 ENGINE HANGER - - - -

● Non-reusable part ★ Precoated part

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Reconnected to auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

CAUTION:
·
A340377C22
0.542,1.115 0.958,1.115 false 0.344,1.01 0.656,1.208 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the engine lifter


Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.


·
A340359C12
0.375,1.135 0.75,1.281 true 0.135,1.031 0.448,1.229 0.313,0.198 10 false *a
*a High temperature areas


Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.

·

Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.


·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here(Click here)



Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Z101186

Click here(Click here)

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Z101186

Click here(Click here)

Hide 4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.REMOVE FRONT WHEELS

Hide 51410 6.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442C 7.REMOVE ENGINE UNDER COVER LH

Hide 51441C 8.REMOVE ENGINE UNDER COVER RH

Hide 51447D 9.REMOVE NO. 4 CENTER ENGINE UNDER COVER

Z101186

Click here(Click here)

Hide 10.DRAIN ENGINE OIL

Z101186

Click here(Click here)

Hide 11.DRAIN ENGINE COOLANT

Z101186

Click here(Click here)

Hide 12.DRAIN HYBRID TRANSAXLE FLUID

Z101186

Click here(Click here)

Hide G92A0 13.REMOVE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

Hide 82662A 14.REMOVE NO. 1 RELAY BLOCK COVER

a.
A476149


Hide 15.REMOVE ENGINE WIRE

a.
A486021


Hide 33820B 16.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
A486631


Hide 16571C 17.DISCONNECT NO. 1 RADIATOR HOSE

a.
A460184


Hide 16572D 18.DISCONNECT NO. 2 RADIATOR HOSE

a.
A460185


Hide G922H 19.DISCONNECT INLET HYBRID RADIATOR HOSE

a.
A460186


Hide G922F 20.DISCONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

a.
A460187


Hide 23826 21.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A460188


Hide 77261D 22.DISCONNECT FUEL TANK TO CANISTER TUBE

a.
A460189


Hide 16290F 23.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

Hide 87245 24.DISCONNECT INLET HEATER WATER HOSE

Hide 23901 25.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A462282N01
0.125,0 0.406,0.354 0.281,0.354 18 false i 3.729,0.01 4.01,0.365 0.281,0.354 18 false ii

i.

Remove the No. 1 fuel pipe clamp for the fuel tube sub-assembly.


ii.

Disconnect the fuel tube sub-assembly from the fuel pump assembly.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 88711 26.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 88704 27.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 28. SECURE STEERING WHEEL

Z101186

Click here(Click here)

Hide 45259A 29.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 30.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Z101186

Click here(Click here)

Hide 17410 31.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Z101186

Click here(Click here)

Hide 12318 33.REMOVE ENGINE MOUNTING STAY LH

a.
A460191


Hide 34.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.
A476150N01
0.438,0.146 0.719,0.5 0.281,0.354 18 false i 3.885,0.115 4.167,0.469 0.281,0.354 18 false ii 0.208,1.906 0.49,2.26 0.281,0.354 18 false iii 3.885,1.969 4.167,2.323 0.281,0.354 18 false iv

i.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




ii.

Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


iii.

Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.


iv.

Remove the 10 bolts to separate the front suspension crossmember sub-assembly from the vehicle.

1. Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.





Hide 12353 35.REMOVE ENGINE MOUNTING BRACKET CAP

a.
A458275N02
0.427,0.073 0.729,0.406 0.302,0.333 18 false i 3.969,0.031 4.271,0.365 0.302,0.333 18 false ii

i.

Turn over the engine mounting bracket cap to the upper part.


ii.

While rotating in the direction shown in the diagram, remove the engine mounting bracket cap.



Hide 36.INSTALL ENGINE HANGER

a.
A458276N01
0.583,0.219 0.865,0.573 0.281,0.354 18 false i

i.

Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-25030
No. 2 Engine Hanger 12282-25010
Bolt 91552-F1040


1. Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.





Hide 12372A 37.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH

Z101186

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.



a.
A458277


Hide G92A0A 38.DISCONNECT INVERTER RESERVE TANK ASSEMBLY

a.
A460194


Hide 12305 39.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

Z101186

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.



a.
A460195


Hide 11363A 41.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 82121 43.REMOVE ENGINE WIRE

a.
A462284


Hide 44.REMOVE WATER HOSE

a.
A460198


Hide 45.REMOVE ENGINE ASSEMBLY

Z101186

Click here(Click here)

Hide 31270 46.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

Z101186

Click here(Click here)

Hide 13405 47.REMOVE FLYWHEEL SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 19315 48.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 88370 49.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

Z101186

Click here(Click here)

Hide 50.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.
A460432


Hide 51.REMOVE ENGINE HANGER