Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2020.08–2021.07
RM3700E _52 Drivetrain _093735 P910 HYBRID TRANSMISSION / TRANSAXLE _0441815 TRANSMISSION CONTROL CABLE A

P910 HYBRID TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C442367N01
6.448,0.229 6.781,0.229 false 6.177,1.313 6.51,1.313 false 3.75,1.125 4.083,1.125 false 2.333,2.26 2.646,2.458 0.313,0.198 10 false x4 2.813,2.385 3.125,2.583 0.313,0.198 10 false x4 3.75,1.906 4.063,2.104 0.313,0.198 10 false x9 6.271,0.031 6.552,0.385 0.281,0.354 18 false 1 6.583,1.146 6.865,1.5 0.281,0.354 18 false 2 4.146,0.979 4.427,1.333 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 SECURE VEHICLE - (Click here) - -
2 HYBRID MOTOR CONTROL INVERTER ASSEMBLY G92A0 - - -
3 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -

C442368N04
0.25,0.167 7,4.667 6.75,4.5 5.51,0.323 5.844,0.323 false 1.333,1.333 1.667,1.333 false 5.896,2.49 6.229,2.49 false 0.906,3.729 1.24,3.729 false 0.25,2.375 7,2.375 false 3.927,1.771 3.76,1.771 3.76,1.771 3.667,1.542 false 3.844,3.979 3.677,3.979 3.677,3.979 3.583,3.844 false 2.51,5.083 2.844,5.083 false 5.354,1.583 5.667,1.781 0.313,0.198 10 false x2 5.49,1.219 5.802,1.417 0.313,0.198 10 false x2 2.635,2.167 2.948,2.365 0.313,0.198 10 false x2 2.313,1.833 2.625,2.031 0.313,0.198 10 false x2 5.906,0.229 6.167,0.438 0.26,0.208 10 false ● 1.146,1.229 1.344,1.427 0.198,0.198 10 false ● 5.719,3.49 6.031,3.708 0.313,0.219 10 false x2 5.771,3.177 6.083,3.396 0.313,0.219 10 false x2 2.063,4.51 2.375,4.729 0.313,0.219 10 false x2 1.719,4.198 2.031,4.417 0.313,0.219 10 false x2 6.292,2.396 6.552,2.604 0.26,0.208 10 false ● 0.74,3.646 0.938,3.865 0.198,0.219 10 false ● 0.333,0.24 0.708,0.479 0.375,0.24 12 false *A 0.333,2.448 0.708,2.688 0.375,0.24 12 false *B 4.229,1.635 4.51,1.99 0.281,0.354 18 false 5 2.906,4.979 3.188,5.333 0.281,0.354 18 false 4 4.125,3.854 4.406,4.208 0.281,0.354 18 false 5 2.552,5.396 2.865,5.615 0.313,0.219 10 false x2 1.604,5.49 1.917,5.708 0.313,0.219 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

4 CENTER NO. 4 ENGINE UNDER COVER 51447D - - -
5 FRONT EXHAUST PIPE ASSEMBLY 17410 (Click here) - -

*A for 2WD *B for AWD
● Non-reusable part - -

C445034N01
5.615,1.094 5.948,1.094 false 1.177,1.177 1.51,1.177 false 5.99,0.979 6.313,1.26 0.323,0.281 18 false 6 0.979,1.031 1.302,1.313 0.323,0.281 18 false 7 3.76,1.875 4.073,2.073 0.313,0.198 10 false x4

Procedure Part Name Code
Z101186

Z101188

Z101187

6 FRONT NO. 2 FLOOR HEAT INSULATOR 58153 - - -
7 FRONT NO. 1 FLOOR HEAT INSULATOR 58151 - - -

C442369N03
2.438,1.115 2.854,1.115 false 0.969,3.677 1.281,3.677 false 0.573,4.625 0.885,4.625 false 2.219,0.979 2.5,1.333 0.281,0.354 18 false 8 0.719,3.542 1,3.896 0.281,0.354 18 false 9 5.24,4.052 5.552,4.25 0.313,0.198 10 false x2 0.396,4.531 0.656,4.729 0.26,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

8 REAR CONSOLE BOX ASSEMBLY 58910C - - -
9 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Gas leaks from exhaust system Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.SECURE VEHICLE

a.
C432457N01
0.417,0.083 0.698,0.438 0.281,0.354 18 false i

i.

Fully apply the parking brake and chock a wheel.

CAUTION:
·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.





Hide G92A0 2.REMOVE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

Hide 51410 3.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51447D 4.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 17410 5.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Z101186

Click here(Click here)

Hide 58153 6.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR

a.
C429504


Hide 58151 7.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
C445361


Hide 58910C 8.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 33820B 9.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C442387N01
0.385,0 0.667,0.354 0.281,0.354 18 false i

i.

Move the shift lever to N.



b.
C442370C01
3.76,1.208 3.948,1.302 true 3.604,1.115 3.823,1.271 0.219,0.156 10 false *1 4.229,1.448 4.438,1.604 0.208,0.156 10 true *a 0.052,0.229 0.188,0.521 0.135,0.292 18 true i 2.75,0.271 2.938,0.563 0.188,0.292 18 true ii 6.177,0.281 6.427,0.573 0.25,0.292 18 true iv 6.615,1.188 6.865,1.479 0.25,0.292 18 true iii 4.844,2.156 5.094,2.448 0.25,0.292 18 true ix 4.177,2.385 4.469,2.688 0.292,0.302 18 true vii 3.104,2.448 3.417,2.729 0.313,0.281 18 true viii 1.948,2.24 2.198,2.521 0.25,0.281 18 true vi 0.958,3.094 1.146,3.385 0.188,0.292 18 true v
*1 Lock Nut - -
*a Counterclockwise - -


i.

Disconnect the transmission control cable assembly from the transmission floor shift assembly.


ii.

Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, disconnect the transmission control cable assembly from the transmission floor shift assembly.


iii.

Remove the nut to disconnect the transmission control cable assembly from the control shaft lever.


iv.

Remove the clip to disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


v.

Disengage the clamp to separate the transmission control cable assembly.


vi.

Remove the bolt to disconnect the transmission control cable assembly from the hybrid vehicle transaxle assembly.


vii.

Remove the nut.


viii.

Disengage the guide to disconnect the transmission control cable assembly from the vehicle body.


ix.

Remove the 2 nuts and transmission control cable assembly from the vehicle body.