Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › OIL COOLER › 2020.08–2021.07
RM3700E _52 Drivetrain _093735 P910 HYBRID TRANSMISSION / TRANSAXLE _0441816 OIL COOLER A

P910 HYBRID TRANSMISSION / TRANSAXLE  OIL COOLER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C429481N01
4.698,1.667 5.115,1.667 false 1.375,2 1.792,2 false 4.49,1.51 4.771,1.865 0.281,0.354 18 false 2 1.188,1.844 1.469,2.198 0.281,0.354 18 false 1 3.625,2.438 3.844,2.656 0.219,0.219 10 false x9 2.896,2.823 3.115,3.042 0.219,0.219 10 false x4 2.521,2.917 2.74,3.135 0.219,0.219 10 false x4 6.292,1.542 6.51,1.76 0.219,0.219 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
2 ENGINE UNDER COVER LH 51442C - - -

C442374N02
5.74,0.833 6.156,0.833 false 4.073,2.177 4.406,2.177 false 2.219,2.604 2.646,2.604 false 0.938,3.104 1.354,3.104 false 0.531,4.135 0.948,4.135 false 2.75,4.188 2.865,3.833 2.865,3.833 3.031,3.833 false 3.583,2.292 3.583,2.708 false 1.583,5 1.583,5.417 false 6.219,0.688 6.5,1.042 0.281,0.354 18 false 3 1.5,5.458 1.75,5.75 0.25,0.292 18 false 4 0.354,3.958 0.635,4.313 0.281,0.354 18 false 5 0.688,2.948 0.969,3.302 0.281,0.354 18 false 9 2,2.448 2.281,2.802 0.281,0.354 18 false 8 3.521,2.74 3.802,3.094 0.281,0.354 18 false 6 3.365,3.667 3.646,4.021 0.281,0.354 18 false 7 2.313,5.271 2.625,5.469 0.313,0.198 10 false x3 4.479,2.094 4.792,2.292 0.313,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

3 HYBRID MOTOR CONTROL INVERTER ASSEMBLY G92A0 - - -
4 INLET HYBRID RADIATOR HOSE G922H - - -
5 OUTLET NO. 1 HYBRID WATER PUMP HOSE G922F - - -
6 NO. 2 MOTOR COOLING PIPE G1252A - - -
7 MOTOR COOLING COOLER G125A (Click here) - -
8 NO. 2 MOTOR COOLING HOSE G1272C (Click here) - -
9 NO. 1 MOTOR COOLING HOSE G1271C (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during motor cooling cooler removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442C 2.REMOVE ENGINE UNDER COVER LH

Hide G92A0 3.REMOVE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

Hide G922H 4.DISCONNECT INLET HYBRID RADIATOR HOSE

Hide G922F 5.DISCONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

Hide G1252A 6.REMOVE NO. 2 MOTOR COOLING PIPE

a.
C429460E01
1.427,0.125 1.708,0.427 0.281,0.302 18 true i 1.063,1.167 1.344,1.469 0.281,0.302 18 true ii 4.667,0.302 4.948,0.604 0.281,0.302 18 true iii

i.

Remove the oil cooler union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.


ii.

Disengage the clamp.


iii.

Slide the clip and remove the No. 2 motor cooling pipe from the No. 2 motor cooling hose.



Hide G125A 7.REMOVE MOTOR COOLING COOLER

a.
C442375E01
0.083,0.042 0.354,0.333 0.271,0.292 18 true i 4,0.042 4.271,0.333 0.271,0.292 18 true ii

i.

Slide the clip and disconnect the No. 1 motor cooling hose from the No. 1 motor cooling pipe.


ii.

Remove the 3 bolts and motor cooling cooler from the hybrid vehicle transaxle assembly.

NOTICE:

Make sure not to remove the No. 1 motor cooling hose and No. 2 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.




Hide G1272C 8.REMOVE NO. 2 MOTOR COOLING HOSE

Z101186

HINT:

Perform this procedure only when replacement of the motor cooling cooler is necessary.



a.
C429465


Hide G1271C 9.REMOVE NO. 1 MOTOR COOLING HOSE

Z101186

HINT:

Perform this procedure only when replacement of the motor cooling cooler is necessary.



a.
C429467