Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › ENGINE COOLANT TEMPERATURE SENSOR › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442026 ENGINE COOLANT TEMPERATURE SENSOR A

M15A-FKS ENGINE CONTROL  ENGINE COOLANT TEMPERATURE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A472753N01
4.885,3.854 5.219,3.854 false 4.156,0.979 4.49,0.979 false 3.167,0.375 3.5,0.375 false 6.417,0.344 6.75,0.344 false 4.302,0.875 4.635,0.635 4.635,0.635 4.781,0.635 false 5.302,3.708 5.583,4.063 0.281,0.354 18 false 1 6.208,0.208 6.49,0.563 0.281,0.354 18 false 2 2.979,0.24 3.24,0.677 0.26,0.438 18 false 3 4.802,0.823 5.063,1.26 0.26,0.438 18 false 4 4.906,0.531 5.167,0.969 0.26,0.438 10 false ● 3.51,4.49 3.771,4.74 0.26,0.25 10 false x4 4.146,4.563 4.406,4.813 0.26,0.25 10 false x4 4.792,4.49 5.052,4.74 0.26,0.25 10 false x9

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO.1 ENGINE UNDER COVER ASSY 51410 - - -
2 DRAIN ENGINE COOLANT - - (Click here) -
3 ECM 89661 - - -
4 ENGINE COOLANT TEMPERATURE SENSOR 89422A (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during radiator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of engine coolant temperature sensor Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC P063051 is output (Click here)
ECU security key
·

DTCs are stored

·

Vehicle control history (RoB) are stored


(Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 51410 1.REMOVE NO.1 ENGINE UNDER COVER ASSY

Hide 2.DRAIN ENGINE COOLANT

Hide 89422A 4.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Z101186

NOTICE:

If the engine coolant temperature sensor has been struck or dropped, replace it.



a.
A458053N01
0.563,0.073 0.771,0.365 0.208,0.292 18 true i 4.521,0.052 4.76,0.344 0.24,0.292 18 true ii