Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0442914 REAR MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM  P0C3100  Drive Motor Inverter Temperature Sensor "C" Circuit  


DTC SUMMARY

MALFUNCTION DESCRIPTION


This DTC indicates an abnormality in the rear air cooling system. The cause of this malfunction may be one of the following:

Rear inverter internal malfunction
·

Rear inverter internal circuit malfunction

·

Malfunction in ECU controlling rear inverter

·

Rear inverter control sensor malfunction (base temperature sensor)


Rear inverter cooling system malfunction
·

Air cooling fan malfunction

·

Air cooling fin clogging



DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0C3100 Drive Motor Inverter Temperature Sensor "C" Circuit The base temperature increases, and at the same time the rear inverter temperature also increases.
(3 trip detection logic)
·

Wire harness or connector

·

HV inverter cooling fan

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Comes on
Rear Motor Generator A

Related Data List
DTC No. Data List

*1: Temperature of inverter base plate (frame body) upon which elements are mounted

P0C3100
·

Rear Motor Base Temperature*1

·

Rear Motor Inverter Temperature



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.

4.

Turn the ignition switch to ON (READY) and wait for 5 seconds or more.

5.

Drive the vehicle for approximately 10 minutes mainly using the engine.

6.

Check that the deviation of the "Rear Motor Base Temperature" and "Rear Motor Inverter Temperature" on the Data List is within 60°C (34°F).

7.

Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.




WIRING DIAGRAM

Refer to the wiring diagram for the Rear Cooling System.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Rear Cooling System

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > Rear Motor Generator > Trouble Codes
50001 396
Result:
Result Proceed to
Only P0C3100 for Rear motor generator control system is output A
P0C3100 and DTCs other than the DTCs in the table below are output B
P0C3100 and Insulation malfunction of Hybrid control system DTCs in the table below are output C
P0C3100 and High voltage circuit malfunction of Hybrid control system DTCs in the table below are output D
P0C3100 and Microcomputer malfunction of Rear motor generator control system DTCs in the table below are output E
P0C3100 and Microcomputer malfunction of Motor generator control system DTCs in the table below are output F
P0C3100 and Power source circuit malfunction of Rear motor generator control system DTCs in the table below are output G
P0C3100 and Communication malfunction of Rear motor generator control system DTCs in the table below are output H
P0C3100 and Communication malfunction of Motor generator control system DTCs in the table below are output I
P0C3100 and Sensor and actuator circuit malfunction of Rear motor generator control system DTCs in the table below are output J


Table 1
Malfunction Content System Relevant DTC
Insulation malfunction Hybrid control system P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure
P1C8049 Hybrid/EV Battery Voltage System Isolation (Rear Motor Area) Internal Electronic Failure
High voltage circuit malfunction Hybrid control system P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Battery or Open
P1C8449 High Voltage Power Resource Circuit Short during Ready ON

Table 2
Malfunction Content System Relevant DTC
Microcomputer malfunction Rear motor generator control system P0A1C1F Drive Motor B" Control Module Circuit Intermittent
P1C2C1C Drive Motor B" Control Module AD Converter Circuit Voltage Out of Range
P1C2C49 Drive Motor B" Control Module AD Converter Circuit Internal Electronic Failure
Motor generator control system P0A1C49 Drive Motor B" Control Module Internal Electronic Failure"
Power source circuit malfunction Rear motor generator control system P06B31C Drive Motor B" Control Module Position Sensor REF Power Source Circuit Voltage Out of Range
P262C1C Drive Motor B" Control Module Offset Power Circuit Voltage Out of Range
Communication malfunction Rear motor generator control system P314987 Lost Communication between Drive Motor A" and "B" Missing Message
Motor generator control system P314887 Lost Communication between Drive Motor A" and "B" Missing Message"
Sensor and actuator circuit malfunction Rear motor generator control system P0AF211 Drive Motor Inverter Temperature Sensor B" Circuit Short to Ground
P0AF215 Drive Motor Inverter Temperature Sensor B" Circuit Short to Battery or Open
P0AF21F Drive Motor Inverter Temperature Sensor B" Circuit Intermittent
P0BD111 Drive Motor Inverter Temperature Sensor C" Circuit Circuit Short to Ground
P0BD115 Drive Motor Inverter Temperature Sensor C" Circuit Circuit Short to Battery or Open
P0BD11F Drive Motor Inverter Temperature Sensor C" Circuit Circuit Intermittent
P310462 Drive Motor Inverter Temperature Sensor B" Signal Compare Failure

HINT:
·

P0C3100 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

C

D

E

GO TO DTC CHART (REAR MOTOR GENERATOR CONTROL SYSTEM)

F

G

GO TO DTC CHART (REAR MOTOR GENERATOR CONTROL SYSTEM)

H

GO TO DTC CHART (REAR MOTOR GENERATOR CONTROL SYSTEM)

I

J

GO TO DTC CHART (REAR MOTOR GENERATOR CONTROL SYSTEM)

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>P0A4516

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK REAR COOLING SYSTEM

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK REAR COOLING SYSTEM

NEXT

REPLACE REAR INVERETER COOLING FAN