Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0442914 REAR MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM  P1C661F  Drive Motor "B" Control Module Circuit Intermittent  P1CAE49  Drive Motor "B" Position Sensor Internal Electronic Failure  P1CB138  Drive Motor "B" Position Sensor REF Signal Frequency Incorrect  


DESCRIPTION

The rear motor generator control ECU, which is built into the rear inverter assembly, monitors its internal operation and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P1C661F Drive Motor "B" Control Module Circuit Intermittent Excitation signal (REF signal) for resolver angle detection cycle malfunction detected when DTC P0C7A17 or P1C5E19 is stored.
(1 trip detection logic)
·

Wire harness or connector

·

Floor wire

·

Rear traction motor assembly

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Does not come on
Rear Motor Generator A
P1CAE49 Drive Motor "B" Position Sensor Internal Electronic Failure Rear motor resolver angle malfunction: The difference between the resolver angle for control and estimated resolver angle exceeds the allowable limit.
(1 trip detection logic)
·

Wire harness or connector

·

Floor wire

·

Rear traction motor assembly

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P1CB138 Drive Motor "B" Position Sensor REF Signal Frequency Incorrect Rear motor resolver REF signal cycle malfunction: Excitation signal (REF signal) for resolver angle detection cycle malfunction.
(1 trip detection logic)
·

Wire harness or connector

·

Floor wire

·

Rear traction motor assembly

·

Rear hybrid motor control inverter assembly


Does not come on Master Warning:
Comes on
Rear Motor Generator A

HINT:

Although the DTC titles generator control module, these DTCs relate to the motor control module.


Related Data List
DTC No. Data List
P1CAE49 Rear Motor Revolution
P1CB138

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.*

*: Lightly wiggle the connectors and wire harnesses up and down and right and left.

4.

Turn the ignition switch to ON (READY) with the shift lever in P and wait for 5 seconds or more.

5.

Depress the accelerator pedal of the vehicle with the engine stopped and the shift lever in P to start the engine.

6.

Keep the engine running for 5 seconds or more.

7.

Drive the vehicle forward with the shift lever in D for 5 m (16 ft.) or more.

8.

Drive the vehicle backward with the shift lever in R for 5 m (16 ft.) or more.

9.

Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.

10.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.




WIRING DIAGRAM

Refer to the wiring diagram for Rear Motor Resolver Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Rear Motor Resolver Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

If the problem symptom cannot be reproduced, performing a road test on a road on which the vehicle tends to vibrate will make it easier to reproduce the symptom.

·

If the resolver is malfunctioning, the vehicle may not drive smoothly.

·

When inspecting the connectors, if it is difficult to judge if a connector was disconnected, deformed or improperly secured, disconnect and reconnect the connector and then check for DTCs again. Check if the same DTC is output. If the same DTC is not output, improper connection of connectors is suspected.

·

As a malfunction detection threshold may be exceeded when performing the vibration or heat connector inspections, make sure to perform the following inspection to check that the DTC was not stored due to the malfunction of a part.



PROCEDURE

1.CHECK DTC OUTPUT (REAR MOTOR GENERATOR CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Rear Motor Generator > Trouble Codes
50001 396
Result:
Result Proceed to
Only P1C661F, P1CAE49 or P1CB138 is output A
P1C661F, P1CAE49 or P1CB138 is output and DTCs other than the DTCs in the table below are output B
P1C661F, P1CAE49 or P1CB138 is output and any DTCs in the table below are output C


Relevant DTC
P0A4516 Drive Motor B" Position Sensor Circuit Voltage Below Threshold
P0C5513 Drive Motor B" Position Sensor Circuit "A" Circuit Open
P0C5516 Drive Motor B" Position Sensor Circuit "A" Circuit Voltage Below Threshold
P0C5517 Drive Motor B" Position Sensor Circuit "A" Circuit Voltage Above Threshold
P0C5F13 Drive Motor B" Position Sensor Circuit "B" Circuit Open
P0C5F16 Drive Motor B" Position Sensor Circuit "B" Circuit Voltage Below Threshold
P0C5F17 Drive Motor B" Position Sensor Circuit "B" Circuit Voltage Above Threshold


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

C

GO TO DTC CHART (REAR MOTOR GENERATOR CONTROL SYSTEM))

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>P0A4516

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK REAR MOTOR RESOLVER CIRCUIT

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK REAR MOTOR RESOLVER CIRCUIT

NEXT

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY