| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | PRECAUTION | - | - | - | |
| 2 | DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL | - | - | - | |
| 3 | REAR CONSOLE BOX ASSEMBLY | 58910C | - | - | - |
| 4 | TURN SIGNAL SWITCH | 84329 | - | - | - |
| 5 | FRONT DOOR SCUFF PLATE RH | 67913B | - | - | - |
| 6 | FRONT DOOR SCUFF PLATE LH | 67914B | - | - | - |
| 7 | COWL SIDE TRIM BOARD RH | 62111C | - | - | - |
| 8 | COWL SIDE TRIM BOARD LH | 62112 | - | - | - |
| 9 | NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY | 55606 | - | - | - |
| 10 | NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY | 55607 | - | - | - |
| 11 | FRONT DOOR OPENING TRIM WEATHERSTRIP RH | 62311B | - | - | - |
| 12 | FRONT DOOR OPENING TRIM WEATHERSTRIP LH | 62312B | - | - | - |
| 13 | NO. 1 INSTRUMENT SIDE PANEL | 55317E | - | - | |
| 14 | NO. 2 INSTRUMENT SIDE PANEL | 55318F | - | - | |
| *A | w/ Cover | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 15 | GLOVE COMPARTMENT DOOR ASSEMBLY | 55550 | - | - | - |
| 16 | LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL | 55433B | - | - | - |
| 17 | GLOVE COMPARTMENT DOOR CHECK CUSHION | 55557A | - | - | - |
| 18 | FRONT PILLAR GARNISH RH | 62211 | - | - | - |
| 19 | FRONT PILLAR GARNISH LH | 62212 | - | - | - |
| 20 | FRONT NO. 2 SPEAKER ASSEMBLY | 86160P | - | - | - |
| 21 | HOOD LOCK CONTROL LEVER SUB-ASSEMBLY | 53601 | - | - | - |
| 22 | LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY | 55480D | - | - | |
| 23 | INSTRUMENT PANEL HOLE COVER | 55548A | - | - | |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 24 | INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY | 55410C | - | - | - |
| 25 | COMBINATION METER ASSEMBLY | 83100 | - | - | - |
| 26 | INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY | 55406B | - | - | - |
| 27 | AIR CONDITIONING CONTROL ASSEMBLY | 55900 | - | - | - |
| 28 | INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY | 55405B | - | - | - |
| 29 | INSTRUMENT PANEL CENTER REGISTER ASSEMBLY | 55670A | - | - | - |
| 30 | RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET | 86140A | - | - | - |
| 31 | INSTRUMENT CLUSTER FINISH CENTER PANEL ASSEMBLY | 55720A | - | - | |
| 32 | INSTRUMENT PANEL CENTER TRAY | 55624A | - | - | |
| *A | for Automatic Air Conditioning System | *B | for Manual Air Conditioning System |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 33 | INSTRUMENT CLUSTER FINISH END PANEL | 55414A | - | - | - |
| 34 | INSTRUMENT MAIN PANEL | 55313A | - | - | - |
| 35 | INSTRUMENT PANEL SUB-ASSEMBLY | 55302C | - | - | - |
| 36 | DEFROSTER NOZZLE ASSEMBLY | 55950G | - | - | - |
| 37 | AUTOMATIC LIGHT CONTROL SENSOR | 89120A | - | - | - |
| 38 | NO. 1 INSTRUMENT PANEL PIN | 55328 | - | - | - |
| *A | w/ Headup Display | - | - |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel sub-assembly removal/installation are shown below.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>REMOVAL
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
58910C
3.REMOVE REAR CONSOLE BOX ASSEMBLY
84329
4.REMOVE TURN SIGNAL SWITCH
67913B
5.REMOVE FRONT DOOR SCUFF PLATE RH
67914B
6.REMOVE FRONT DOOR SCUFF PLATE LH
Use the same procedure as for the RH side.
62111C
7.REMOVE COWL SIDE TRIM BOARD RH
62112
8.REMOVE COWL SIDE TRIM BOARD LH
Use the same procedure as for the RH side.
55606
9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
55607
10.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Cover)
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
62311B
11.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
62312B
12.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Use the same procedure as for the RH side.
55317E
13.REMOVE NO. 1 INSTRUMENT SIDE PANEL
|
Protective Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) | - | - |
Using a molding remover A, disengage the clips and guides to remove the No.1 instrument side panel.
55318F
14.REMOVE NO. 2 INSTRUMENT SIDE PANEL
Use the same procedure as for the No. 1 side.
55550
15.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
|
Push |
|
Remove in this Direction |
55433B
16.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
|
Remove in this Direction | - | - |
55557A
17.REMOVE GLOVE COMPARTMENT DOOR CHECK CUSHION
62211
18.REMOVE FRONT PILLAR GARNISH RH
| *a | Release Lever | - | - |
|
Pull up | - | - |
Pull up the front pillar garnish LH to disengage the front pillar garnish clip and clip as shown in the illustration.
Push the release lever and separate the front pillar garnish clip from the vehicle body.
When the front pillar garnish clip cannot be removed using your fingers:
|
Lift in this Direction |
|
Remove in this Direction |
While pressing the part shown in the illustration with your finger, move the front pillar garnish clip in the direction indicated by the arrow.
While pulling the front pillar garnish clip in the direction indicated by the arrow, push the part shown in the illustration with the end of a screwdriver and remove the front pillar garnish clip.
|
Remove in this Direction | - | - |
Disengage the guides as shown in the illustration.
Disengage the claws to disconnect the front No.2 speaker assembly and remove the front pillar garnish LH.
Remove the front pillar garnish clip from the front pillar garnish RH.
Protect the curtain shield airbag assembly.
| *a | Protective Cover | - | - |
|
Adhesive Tape | - | - |
Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.
Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish LH is removed.
62212
19.REMOVE FRONT PILLAR GARNISH LH
Use the same procedure as for the RH side.
86160P
20.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY
53601
21.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
55480D
22.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
|
|
|
Remove in this Direction | - | - |
55548A
23.REMOVE INSTRUMENT PANEL HOLE COVER
55410C
24.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
|
Remove in this Direction | - | - |
83100
25.REMOVE COMBINATION METER ASSEMBLY
55406B
26.REMOVE INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)
55900
27.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
55405B
28.REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY
|
Remove in this Direction | - | - |
55670A
29.REMOVE INSTRUMENT PANEL CENTER REGISTER ASSEMBLY
|
Remove in this Direction | - | - |
55420A
31.REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL ASSEMBLY
|
Remove in this Direction | - | - |
55624A
32.REMOVE INSTRUMENT PANEL CENTER TRAY
|
Remove in this Direction | - | - |
55414A
33.REMOVE INSTRUMENT CLUSTER FINISH END PANEL (w/ Headup Display)
|
Protective Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) | - | - |
Using a molding remover A, disengage the claws and guides to remove the instrument cluster finish end panel.
55313A
34.REMOVE INSTRUMENT MAIN PANEL
|
Protective Tape |
|
Remove in this Direction |
Using a molding remover B, disengage the clips and claws.
|
Remove in this Direction | - | - |
Disconnect the connectors.
Disengage the guides to remove the instrument main panel.
55302C
35.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
| *a | Airbag Connector | *b | Airbag Bolt |
Disconnect the connector.
Remove the bolt <H> and disengage the guide to separate the ground bracket.
Remove the 2 bolts <G>.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
Remove the 3 clips.
Disengage the hooks.
Remove the 5 bolts <F>, screw <E> and nut <I>.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the guides to remove the instrument panel sub-assembly.
55950G
36.REMOVE DEFROSTER NOZZLE ASSEMBLY
89120A
37.REMOVE AUTOMATIC LIGHT CONTROL SENSOR
55328
38.REMOVE NO. 1 INSTRUMENT PANEL PIN