Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0DA31C  Drive Motor "B" Inverter Voltage Sensor "A" Voltage Out of Range  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU detects a VLR sensor malfunction.

The cause of this malfunction may be the following:

Rear inverter voltage sensor internal circuit malfunction
·

Voltage sensor malfunction

·

Rear motor generator control ECU (MGR ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

Rear inverter assembly malfunction

·

MGR malfunction

·

High voltage wire harness malfunction



DESCRIPTION

The rear motor generator control ECU (MGR ECU), which is built into the hybrid motor control rear inverter assembly, uses the voltage sensor built into the rear hybrid motor control inverter assembly to detect high voltage (VLR). The rear motor generator control ECU (MGR ECU) monitors the voltage sensor signal circuit to detect malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0DA31C Drive Motor "B" Inverter Voltage Sensor "A" Voltage Out of Range Rear inverter voltage (VLR) sensor performance malfunction:
In the READY ON state, difference between rear inverter voltage (VLR) and hybrid battery voltage (VB) is large and difference between rear inverter voltage (VLR) and voltage before boosting (VL) is large.
(1 trip detection logic)
·

Rear hybrid motor control inverter assembly

·

Rear traction motor with transaxle assembly

·

Rear traction motor cable


Does not come on Master Warning: Comes on Hybrid Control A

Related Data List
DTC No. Data List
P0DA31C
·

Hybrid/EV Battery Voltage

·

VL-Voltage before Boosting

·

VL-Voltage before Boosting for Rear Motor



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 10 seconds or more.

HINT:

In the P position without the accelerator pedal depressed, check that the values of Data List items "VL-Voltage before Boosting" and "VL-Voltage before Boosting for Rear Motor" are approximately the same.


4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.




WIRING DIAGRAM

Refer to the wiring diagram for the rear motor high-voltage circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Rear Motor High-voltage Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR, REAR MOTOR GENERATOR)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > Rear Motor Generator > Trouble Codes
50001 396
Result:
Result Proceed to
P0DA31C and Microcomputer malfunction of Hybrid control system DTCs in the table below are output A
P0DA31C and Microcomputer malfunction of Motor generator control system DTCs in the table below are output B
P0DA31C and Microcomputer malfunction of Hybrid battery system DTCs in the table below are output C
P0DA31C and Microcomputer malfunction of Rear motor generator control system DTCs in the table below are output D
P0DA31C and Power source circuit malfunction of Motor generator control system DTCs in the table below are output E
P0DA31C and Power source circuit malfunction of Rear motor generator control system DTCs in the table below are output F
P0DA31C and Communication system malfunction of Hybrid control system DTCs in the table below are output G
P0DA31C and Communication system malfunction of Motor generator control system DTCs in the table below are output H
P0DA31C and Sensor and actuator circuit malfunction of Hybrid battery system DTCs in the table below are output I
P0DA31C and System malfunction of Motor generator control system DTCs in the table below are output J
P0DA31C and System malfunction of Rear motor generator control system DTCs in the table below are output K
P0DA31C and DTCs other than the DTCs in the table below are output L
Only P0DA31C for Hybrid control system is output M


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
Motor generator control system P0A1A47 Generator Control Module Watchdog / Safety μC Failure
P0A1A49 Generator Control Module Internal Electronic Failure
P0A1B1F Generator Control Module Circuit Intermittent
P0A1C49 Drive Motor "B" Control Module Internal Electronic Failure
P1C2A1C Generator A/D Converter Circuit Circuit Voltage Out of Range
P1C2A49 Generator A/D Converter Circuit Internal Electronic Failure
P313383 Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect
P313386 Communication Error from Generator to Drive Motor "A" Signal Invalid
P313387 Communication Error from Generator to Drive Motor "A" Missing Message
Hybrid battery system P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance
Rear motor generator control system P0A1C1F Drive Motor "B" Control Module Circuit Intermittent
P1C2C1C Drive Motor "B" Control Module AD Converter Circuit Voltage Out of Range
P1C2C49 Drive Motor "B" Control Module AD Converter Circuit Internal Electronic Failure
Power source circuit malfunction Motor generator control system P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
Rear motor generator control system P262C1C Drive Motor "B" Control Module Offset Power Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message
Motor generator control system P314887 Lost Communication between Drive Motor "A" and "B" Missing Message"
Sensor and actuator circuit malfunction Hybrid battery system P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P1AFD1C Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range
System malfunction Motor generator control system P0E3116 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Below Threshold
P0E3117 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold
Rear motor generator control system P0DA316 Drive Motor "B" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0DA317 Drive Motor "B" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold

HINT:
·

P0DA31C may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

B

C

D

E

F

G

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

H

I

J

K

L

2.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

M

2.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)
2.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)
HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit


Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

3.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HYBRID BATTERY PACK WIRE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

3.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HYBRID BATTERY PACK WIRE CONNECTION CONDITION)
HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit


Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

4.CHECK REAR MOTOR HIGH-VOLTAGE CIRCUIT

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

4.CHECK REAR MOTOR HIGH-VOLTAGE CIRCUIT
HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Rear Motor High-voltage Circuit

If the "Rear Motor High-voltage Circuit" inspection results are normal, perform the next step.


Result:
Proceed to
NEXT



NEXT

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY