Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0446873 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C14E614  Left Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTCs C050C1F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>C050C1F

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C14E614 Left Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open Any of the following is detected:
·

The speed sensor power source voltage is low for 0.5 seconds or more.

·

The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more.


·

Rear speed sensor LH*1

·

Rear speed sensor LH (rear axle hub and bearing assembly LH)*2

·

Skid control sensor wire LH (No. 2 parking brake wire assembly)

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


Brake/EPB A

*1: for AWD

*2: for 2WD


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.



PROCEDURE

1.READ VALUE USING GTS (RL SPEED OPEN)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Speed Open Rear speed sensor LH open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake/EPB > Data List
Tester Display
RL Speed Open
50003 435 104

b.

Check for any momentary interruptions in the wire harness and connectors.

NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Result Proceed to
The value of RL Speed Open is always Normal A
The value of RL Speed Open outputs Error one or more times B



A

2.READ VALUE USING GTS (RL WHEEL SPEED)

B

5.CHECK VEHICLE
2.READ VALUE USING GTS (RL WHEEL SPEED)
a.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RL Wheel Speed
50003 435 16

b.

Check the rear speed sensor LH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

5.CHECK VEHICLE
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C14E614 is not output A
C14E614 is output B



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
for 2WD A
for AWD B



A

6.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

B

9.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
6.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the u4 and uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connectors.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(u4,uO2)Location & Routing

Click Connector(u4)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor LH (Rear Axle Hub & Bearing Assembly LH)

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

u4-2 (+) - uO2-4 (RL+) Always Below 1 Ω
u4-2 (+) or uO2-4 (RL+) - Body ground and other terminals Always 10 kΩ or higher
u4-1 (-) - uO2-3 (RL-) Always Below 1 Ω
u4-1 (-) or uO2-3 (RL-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 PARKING BRAKE WIRE ASSEMBLY)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 PARKING BRAKE WIRE ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A38,uO2)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

A38-34 (RL+) - uO2-4 (RL+) Always Below 1 Ω
A38-34 (RL+) or uO2-4 (RL+) - Body ground Always 10 kΩ or higher
A38-35 (RL-) - uO2-3 (RL-) Always Below 1 Ω
A38-35 (RL-) or uO2-3 (RL-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

Pre-procedure1

a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


c.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(u4)Location & Routing

Click Connector(u4)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor LH (Rear Axle Hub & Bearing Assembly LH)

u4-2 (+) - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the rear speed sensor LH signal after replacement.


HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE


HINT:

The rear speed sensor LH and rear speed sensor rotor LH are incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor LH and rear speed sensor rotor LH need to be replaced, replace the rear axle hub and bearing assembly LH.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the u4 and uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connectors.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(u4,uO2)Location & Routing

Click Connector(u4)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor LH (Rear Axle Hub & Bearing Assembly LH)

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

u4-1 (+) - uO2-4 (RL+) Always Below 1 Ω
u4-1 (+) or uO2-4 (RL+) - Body ground and other terminals Always 10 kΩ or higher
u4-2 (-) - uO2-3 (RL-) Always Below 1 Ω
u4-2 (-) or uO2-3 (RL-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 PARKING BRAKE WIRE ASSEMBLY)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 PARKING BRAKE WIRE ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A38,uO2)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

A38-34 (RL+) - uO2-4 (RL+) Always Below 1 Ω
A38-34 (RL+) or uO2-4 (RL+) - Body ground Always 10 kΩ or higher
A38-35 (RL-) - uO2-3 (RL-) Always Below 1 Ω
A38-35 (RL-) or uO2-3 (RL-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

11.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

Pre-procedure1

a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


c.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(u4)Location & Routing

Click Connector(u4)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor LH (Rear Axle Hub & Bearing Assembly LH)

u4-1 (+) - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the rear speed sensor LH signal after replacement.


HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY