Home › Steering › STEERING COLUMN › STEERING WHEEL › from 2021.07
RM3700E _55 Steering _093030 STEERING COLUMN _0438541 STEERING WHEEL A

STEERING COLUMN  STEERING WHEEL  REMOVAL  


CAUTION / NOTICE / HINT

CONPONENTS (REMOVAL)
C441775N05
6.479,0.302 6.802,0.302 false 4.563,2 4.563,2.333 false 5.604,2.365 5.604,2.698 false 6.5,1.99 6.5,2.323 false 2.458,2.948 2.458,3.229 false 6.01,0.135 6.677,0.479 0.667,0.344 18 false 1, 2 6.438,2.323 6.719,2.677 0.281,0.354 18 false 3 2.49,3.219 2.771,3.573 0.281,0.354 18 false 4 5.542,2.698 5.823,3.052 0.281,0.354 18 false 5 4.5,2.333 4.781,2.688 0.281,0.354 18 false 6 6.052,1.208 6.365,1.406 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - (Click here) - -
3 HORN BUTTON ASSEMBLY 45130 - - -
4 STEERING WHEEL ASSEMBLY 45100 (Click here) - -
5 NO. 1 STEERING WHEEL ORNAMENT 45166 - - -
6 STEERING PAD SWITCH ASSEMBLY 84250A - - -

C463499N02
0.688,1.104 2.802,2.156 2.115,1.052 1.646,2.156 1.646,2.323 false 1.74,0.385 2.052,0.385 false 5.385,1.594 5.385,1.396 false 1.313,1.74 1.625,1.74 false 2.479,1.875 2.479,1.708 false 0.115,0.104 0.49,0.344 0.375,0.24 12 false *A 5.448,1.271 5.76,1.469 0.313,0.198 10 false x2 2.104,0.281 2.417,0.479 0.313,0.198 10 false *3 1.688,2.302 1.969,2.656 0.281,0.354 18 false 7 5.302,1.573 5.615,1.771 0.313,0.198 10 false ●★ 1.677,1.635 1.99,1.833 0.313,0.198 10 false *1 2.417,1.885 2.729,2.083 0.313,0.198 10 false *2

Procedure Part Name Code
Z101186

Z101188

Z101187

7 SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) - (Click here) - -

*A w/ Shift Paddle Switch - -
*1 NO. 1 TRANSMISSION SHIFT SWITCH ASSEMBLY *2 NO. 2 TRANSMISSION SHIFT SWITCH ASSEMBLY
*3 NO. 1 SWITCH WIRE - -
● Non-reusable part ★ Precoated part

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the steering wheel assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

Click here(Click here)

Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Z101186

Click here(Click here)

Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

a.
C456381C01
5.552,0.594 5.823,0.625 5.823,0.625 5.552,0.708 true 1.969,3.563 1.969,3.24 1.969,3.24 2.313,3.24 true 2.167,4.021 2.167,3.25 true 0.271,0.51 0.406,0.792 0.135,0.281 18 true i 4.51,0.188 4.708,0.479 0.198,0.292 18 true iii 5.302,2.313 5.802,2.604 0.5,0.292 18 true ii, iv 0.396,3.073 0.646,3.365 0.25,0.292 18 false v 3.938,3.458 4.24,3.76 0.302,0.302 18 false vi 5.875,0.531 6.052,0.719 0.177,0.188 10 true *a 1.781,5.354 1.958,5.563 0.177,0.208 10 false *b 2.333,3.146 2.677,3.323 0.344,0.177 10 true SST
*a Matchmark *b Hold
V113147

Turn - -


i.

Disconnect each connector.

HINT:

As the illustration shown is an example, the actual details may differ.



ii.

Using a 10 mm hexagon socket wrench, remove the steering wheel assembly set bolt.


iii.

Put matchmarks on the steering wheel assembly and steering main shaft.


iv.

Temporarily install the steering wheel assembly set bolt.

NOTICE:

Do not overtighten the steering wheel assembly set bolt.



v.

Using SST, separate the steering wheel assembly.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031, 09957-04010)
09950-60011  (09951-00330)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.



vi.

Remove the steering wheel assembly set bolt and steering wheel assembly.



Hide 45116 5.REMOVE NO. 1 STEERING WHEEL ORNAMENT

Hide 84250A 6.REMOVE STEERING PAD SWITCH ASSEMBLY

Z101186

Click here(Click here)

Hide 7.REMOVE SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) (w/ Shift Paddle Switch)