Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › from 2021.07
RM3700E _55 Steering _093030 STEERING COLUMN _0438540 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C431406N01
5.948,1.667 6.365,1.667 false 6.469,1.542 6.75,1.896 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING WHEEL ASSEMBLY 45100 - - -

C456356N01
4.969,0.333 5.302,0.333 false 2.844,2.823 2.844,2.146 false 5.042,3.396 5.042,3.052 false 5.365,0.198 5.646,0.552 0.281,0.354 18 false 3 2.885,2.813 3.417,3.146 0.531,0.333 18 false 4 5.104,3.385 5.385,3.74 0.281,0.354 18 false 2 6.563,2.052 6.875,2.25 0.313,0.198 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

2 LOWER STEERING COLUMN COVER - (Click here) - -
3 UPPER STEERING COLUMN COVER - - - -
4 TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY - (Click here) - -

C456357N01
5.177,1.344 5.594,1.344 false 4.458,2.979 4.75,2.979 false 5.104,2.25 5.438,2.25 false 0.521,2.125 0.854,2.125 false 1.979,1.135 2.26,0.781 2.26,0.781 2.427,0.781 false 1.167,3.365 1.5,3.365 false 3.948,5.573 4.281,5.573 false 5.469,4.146 5.802,4.146 false 3.813,4.021 4.146,4.021 false 3.729,3.583 4.042,3.781 0.313,0.198 10 false x2 5.26,3.969 5.667,4.323 0.406,0.354 18 false 5 0.99,3.188 1.417,3.542 0.427,0.354 18 false 7 4.333,5.385 4.729,5.75 0.396,0.365 18 false 6 3.604,3.854 4,4.219 0.396,0.365 18 false 8 0.938,1.948 1.323,2.302 0.385,0.354 18 false 9 2.74,0.625 3.292,0.979 0.552,0.354 18 false 10 5.49,2.073 6.042,2.427 0.552,0.354 18 false 11 5.656,1.156 6.208,1.51 0.552,0.354 18 false 12 5.052,2.802 5.604,3.156 0.552,0.354 18 false 13 3.458,3.917 3.771,4.115 0.313,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

5 CONSOLE BOX ASSEMBLY 58810J - - -
6 FRONT DOOR SCUFF PLATE LH 67914B - - -
7 COWL SIDE TRIM BOARD LH 62112 - - -
8 STOP LIGHT SWITCH MOUNTING ADJUSTER 84345 - - -
9 FRONT DOOR OPENING TRIM WEATHERSTRIP LH 62312B - - -
10 NO. 1 INSTRUMENT SIDE PANEL 55317E (Click here) - -
11 HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 53601 - - -
12 LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY 55480D - - -
13 NO. 1 AIR DUCT 87211 (Click here) - -

● Non-reusable part - -

C456358N01
1.833,2.542 5.5,3.76 3.667,1.219 2.479,1.417 2.865,1.417 false 2.26,3.469 2.656,3.469 false 5.24,1.271 5.635,1.271 false 4.594,3.438 4.99,3.438 false 3.719,2.542 3.719,3.76 false 1.719,1.26 2.5,1.552 0.781,0.292 18 false 15, 16 2.344,2.979 2.854,3.375 0.51,0.396 18 false 15 5.688,1.104 6.198,1.5 0.51,0.396 18 false 17 4.604,2.031 5.01,2.26 0.406,0.229 10 false x2 5.052,3.281 5.563,3.677 0.51,0.396 18 false 14 1.917,3.313 2.427,3.708 0.51,0.396 18 false 14 1.906,2.594 2.156,2.885 0.25,0.292 12 false *A 3.792,2.594 4.042,2.885 0.25,0.292 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

14 COLUMN HOLE COVER SILENCER SHEET 45259A - - -
15 DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 (Click here) - -
16 REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 (Click here) - -
17 STEERING COLUMN ASSEMBLY - - - -

*A for LHD *B for RHD

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the electric power steering column sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Electric power steering column sub-assembly Assist map writing
·

There is a difference in steering effort between turning left and right.

·

Vehicle control history (RoB) are stored


(Click here)
Steering sensor (Including removal and installation) Steering angle setting Parking assist monitor system (Click here)
Adjust steering angle Panoramic view monitor system w/o Advanced Park:(Click here)
w/ Advanced Park:(Click here)
Steering angle neutral point Parking assist monitor system (Click here)
w/o Advanced Park:

Panoramic view monitor system


(Click here)
w/ Entry and Start System:
Steering lock ECU (Steering lock actuator or upper bracket assembly)
Code registration
for HV Model:
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, HV model)

·

Entry and start system (for Start function, HV model)

·

Hybrid control system cannot be started


for Gasoline Model:
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, Gasoline model)

·

Entry and start system (for Start function, Gasoline model)

·

Engine start function


See Service Bulletin for the registration method.

HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 45100 1.REMOVE STEERING WHEEL ASSEMBLY

Hide 2.REMOVE LOWER STEERING COLUMN COVER

Z101186

NOTICE:

Removing the lower steering column cover in the incorrect order will cause the parts to break.



a.
C456359C01
0.49,2.99 0.781,3.313 0.292,0.323 18 false vi 1.438,1.552 1.625,1.854 0.188,0.302 18 true i 4.083,0.125 4.344,0.458 0.26,0.333 18 true v 2.927,1.594 3.104,1.917 0.177,0.323 18 true ii 1.469,0.927 1.719,1.219 0.25,0.292 18 true iv 3.115,0.458 3.344,0.781 0.229,0.323 18 true iii
V100155

Push Area
V100135

Down
V100136

Extend
V113147

Release
V113148

Lock
V113149

Push in this direction


i.

Release the tilt and telescopic lever.


ii.

Fully down the lower the steering column assembly.


iii.

Fully extend the steering column assembly.


iv.

Lock the tilt and telescopic lever.


v.

Remove the 3 screws.


vi.

While pressing the push area shown in the illustration to disengage the claws, slightly lower the lower steering column cover.



Hide 3.REMOVE UPPER STEERING COLUMN COVER

a.
C456360


Hide 4.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

Z101186

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.




a.
C456361C01
4.948,0.552 5.177,0.552 false 4.021,0.052 4.458,0.365 0.438,0.313 18 true ii, iii 0.406,0.042 0.542,0.344 0.135,0.302 18 false i 4.771,0.458 5.083,0.656 0.313,0.198 10 false *a
*a Clamp - -
V113147

Down - -


i.

Disconnect each connector.

HINT:

As the illustration shown is an example, the actual details may differ.



ii.

Using pliers, expand the clamp.


iii.

While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.



Hide 58810J 5.REMOVE CONSOLE BOX ASSEMBLY

Hide 67914B 6.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 7.REMOVE COWL SIDE TRIM BOARD LH

Hide 84345 8.REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER

Hide 62312B 9.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 55317E 10.REMOVE NO. 1 INSTRUMENT SIDE PANEL

Z101186

Click here(Click here)

Hide 53601 11.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55480D 12.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 87211 13.REMOVE NO. 1 AIR DUCT

Z101186

Click here(Click here)

Hide 45259A 14.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C456362C01
0.469,0.042 0.781,0.271 0.313,0.229 12 false *A 4.083,0.052 4.396,0.344 0.313,0.292 12 false *B
*A for LHD *B for RHD



Hide 45260 15.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C456363C01
4.583,1.49 4.688,1.417 4.688,1.417 4.51,1.365 true 4.219,0.896 4.354,1.156 0.135,0.26 18 true i 2.906,1.115 3.063,1.385 0.156,0.271 18 true ii 3.854,0.49 4.094,0.771 0.24,0.281 18 true iii 4.75,1.302 4.948,1.5 0.198,0.198 10 true *a
*a Matchmark - -
V113147

Disconnect in this direction - -


i.

Put matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.


ii.

Remove the bolt.


iii.

Disconnect the No. 2 steering intermediate shaft assembly from the steering gear assembly.



Hide 45260 16.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C456364C01
2.333,0.5 2.438,0.344 2.438,0.344 2.24,0.427 true 2.854,1.052 3.01,1.302 0.156,0.25 18 true ii 3.865,0.104 4.115,0.375 0.25,0.271 18 true iii 2.073,0.073 2.208,0.333 0.135,0.26 18 true i 2.49,0.229 2.677,0.417 0.188,0.188 10 true *a
*a Matchmark - -
V113147

Remove in this direction - -


i.

Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.


ii.

Remove the bolt.


iii.

Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.



Hide 17.REMOVE STEERING COLUMN ASSEMBLY

a.
C456365