| *A | for Manual Transaxle | *B | for CVT |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | ★ | Precoated part |
| *A | for Manual Transaxle | *B | for CVT |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| *a | for CVT: x5
for Manual Transaxle: x4 |
- | - |
| *A | for CVT | *B | for Manual Transaxle |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
Adhesive 1324 | ★ | Precoated part |
| *a | BLACK COLOR: x1
SILVER COLOR: x5 |
- | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 28 | FRONT EXHAUST PIPE ASSEMBLY | 17410 | ( )
|
- | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *A | for Manual Transaxle | *B | for CVT |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
| *A | for LHD | *B | for RHD |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *A | for TMMF Made | *B | for TMC Made |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
2.REMOVE ENGINE FROM ENGINE STAND
88310
3.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY
27020
4.INSTALL GENERATOR WITH REGULATOR ASSEMBLY
for 80A Type:
Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>GENERATOR (for 80A Type)>INSTALLATION
for 100A Type:
Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>GENERATOR (for 100A Type)>INSTALLATION
16620D
5.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
19315
7.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
31250
9.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)
82121
14.INSTALL ENGINE WIRE
| *A | for CVT | *B | for Manual Transaxle |
11363A
15.INSTALL FLYWHEEL HOUSING SIDE COVER
28100
16.INSTALL STARTER ASSEMBLY
17.INSTALL WATER HOSE (for Manual Transaxle)
18.INSTALL WATER HOSE (for CVT)
12305
19.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
|
|
| *a | Temporarily Tighten | - | - |
Install the 2 bolts and nut in the order shown in the illustration.
Connect the air conditioner tube with the clamp.
12372A
20.INSTALL ENGINE MOUNTING INSULATOR LH
|
|
| *a | Temporarily Tighten | - | - |
Install the 4 bolts and nut in the order shown in the illustration.
21.REMOVE ENGINE HANGER
12353
22.INSTALL ENGINE MOUNTING BRACKET CAP
23.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
| *A | for CVT | *B | for Manual Transaxle |
Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
1. Operate the engine lifter and install the engine assembly with transaxle to the vehicle.
Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.
Connect the front suspension crossmember sub-assembly to the vehicle with the 10 bolts.
for CVT:
Install the engine mounting insulator LH to the engine mounting bracket LH with the 3 bolts and nut in the order shown illustration.
for Manual Transaxle:
Install the engine mounting insulator LH to the engine mounting bracket LH with the 4 bolts and nut in the order shown illustration.
Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut in the order shown illustration.
11361J
25.INSTALL FLYWHEEL HOUSING UNDER COVER (for CVT)
31418
26.INSTALL NO. 1 CLUTCH HOSE (for Manual Transaxle)
| *a | 10 mm Union Nut Wrench | *b | Torque Wrench Fulcrum Length |
Connect the No. 1 clutch hose to the clutch flexible hose bracket with a new clip.
Using a 10 mm union nut wrench, connect the bleeder clutch release tube to the No. 1 clutch hose.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
27.INSTALL DRIVE SHAFT ASSEMBLY
17410
28.INSTALL FRONT EXHAUST PIPE ASSEMBLY
45259A
30.INSTALL COLUMN HOLE COVER SILENCER SHEET
88704
31.CONNECT SUCTION HOSE SUB-ASSEMBLY
88711
32.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
23901
33.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly to the fuel pipe.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Install the No. 1 fuel pipe clamp to the fuel tube sub-assembly.
87245
34.CONNECT INLET HEATER WATER HOSE
16290F
35.CONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY
77261D
36.CONNECT FUEL TANK TO CANISTER TUBE
23826
37.CONNECT NO. 1 FUEL VAPOR FEED HOSE
16572D
41.CONNECT NO. 2 RADIATOR HOSE
16571C
42.CONNECT NO. 1 RADIATOR HOSE
43.CONNECT ENGINE WIRE
82662A
44.INSTALL NO. 1 RELAY BLOCK COVER
74404A
45.INSTALL BATTERY CLAMP SUB-ASSEMBLY
17701
47.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17801
48.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
49.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
| *1 | Air cleaner cap sub-assembly clamp | *2 | Guide |
| *a | Top of Vehicle | *b | Right side of vehiclre |
| *c | Stopper | - | - |
Connect the air cleaner cap with air cleaner hose and tighten the hose clamp.
Engage the 2 guides to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.
1. Engage the 2 air cleaner cap sub-assembly clamps to install the air cleaner cap sub-assembly.
Engage the clamp to the air cleaner cap sub-assembly.
1. Connect the mass air flow meter connector.
Connect the ventilation hose to the air cleaner hose.
55701J
50.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
51.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
55815E
52.INSTALL NO. 1 FRONT VENTILATOR SEAL (for LHD)
55815E
53.INSTALL NO. 1 FRONT VENTILATOR SEAL (for RHD)
55734A
54.INSTALL WATER GUARD PLATE RH (for LHD)
55735A
55.INSTALL WATER GUARD PLATE LH (for RHD)
56.INSTALL WINDSHIELD WIPER MOTOR AND LINK
57.INSTALL AUXILIARY BATTERY
64.INSPECT MANUAL TRANSAXLE OIL (for Manual Transaxle)
65.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
70.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK
51447D
76.INSTALL CENTER NO. 4 ENGINE UNDER COVER
51441C
77.INSTALL ENGINE UNDER COVER RH
51442C
78.INSTALL ENGINE UNDER COVER LH
51410
79.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
80.INSTALL FRONT WHEELS
81. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD