Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE › from 2021.07
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441193 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A472782N02
6.552,0.167 6.885,0.167 false 3.25,0.5 3.833,0.5 false 3.375,0.885 3.792,0.885 false 1.323,0.552 1.74,0.552 false 3.917,3.333 4.333,3.333 false 6.052,0.063 7.156,0.417 1.104,0.354 18 false 1, 5 4.229,0.396 5.333,0.75 1.104,0.354 18 false 4, 6 4.229,0.75 5.333,1.104 1.104,0.354 18 false 7 1.104,0.427 2.208,0.781 1.104,0.354 18 false 3 3.76,3.188 4.865,3.542 1.104,0.354 18 false 2 2.75,0.292 3.063,0.49 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 SERVICE PLUG GRIP G3834 - - -
3 ENGINE WIRE 82121 (Click here) - -
4 CONNECTOR COVER ASSEMBLY - (Click here) - -
5 TERMINAL VOLTAGE - (Click here) - -
6 CONNECTOR COVER ASSEMBLY - (Click here) - -
7 HV FLOOR UNDER WIRE 821H1 (Click here) - -

A461511N01
1.25,0.677 3.083,0.677 false 2.656,1.49 2.969,1.49 2.969,1.49 2.969,0.677 false 5.396,0.5 5.802,0.5 false 5.896,1.667 6.302,1.667 false 6.115,3.354 6.521,3.354 false 3.969,4.063 4.375,4.063 false 2.615,3.521 3.021,3.521 false 3.281,0.521 3.646,0.833 0.365,0.313 18 false 10 3.135,0.604 3.354,0.792 0.219,0.188 10 false ● 3.052,3.365 3.417,3.677 0.365,0.313 18 false 12 4.427,3.906 4.792,4.219 0.365,0.313 18 false 11 6.563,3.198 6.927,3.51 0.365,0.313 18 false 13 6.354,1.521 6.552,1.833 0.198,0.313 18 false 9 5.854,0.344 6.052,0.656 0.198,0.313 18 false 8 6.125,2.813 6.354,3.01 0.229,0.198 10 false x6

Procedure Part Name Code
Z101186

Z101188

Z101187

8 REAR CENTER SEAT OUTER BELT ASSEMBLY 73350C - - -
9 BENCH TYPE REAR SEAT CUSHION ASSEMBLY - - - -
10 REAR SEAT CUSHION LOCK HOOK 72693 - - -
11 REAR DOOR SCUFF PLATE INSIDE LH 67918F - - -
12 REAR UNDER COVER 76971G - - -
13 REAR SEAT CUSHION LEG SUB-ASSEMBLY 71403 - - -

● Non-reusable part - -

A461512N08
0.75,3.563 6.25,5.625 5.5,2.063 5.417,1.594 6.906,2.792 1.49,1.198 1.75,2.49 1.75,2.198 false 3.969,1.292 3.969,0.979 false 6.344,2.26 6.344,2 false 2.104,4.521 1.76,4.521 false 4.594,2.844 4.594,2.583 false 5.99,1.198 5.813,1.198 false 4.156,0.458 3.865,0.458 false 1.594,2.5 1.938,2.781 0.344,0.281 18 false 18 4,1.323 4.344,1.604 0.344,0.281 18 false 14 3.552,0.5 3.729,0.677 0.177,0.177 10 false x5 5.25,0.625 5.427,0.802 0.177,0.177 10 false x3 6.281,1.083 6.625,1.365 0.344,0.281 18 false 15 6.219,2.302 6.563,2.583 0.344,0.281 18 false 16 5.958,2.198 6.135,2.375 0.177,0.177 10 false x2 4.063,2.979 4.24,3.156 0.177,0.177 10 false x2 3.177,3.104 3.354,3.281 0.177,0.177 10 false x2 4.458,2.865 4.802,3.146 0.344,0.281 18 false 17 5.792,4.646 5.969,4.823 0.177,0.177 10 false x2 3.75,5.25 3.927,5.427 0.177,0.177 10 false x4 2.417,4.417 2.76,4.698 0.344,0.281 18 false 19 0.844,3.646 1.115,3.854 0.271,0.208 12 false *A 4.49,0.333 4.833,0.615 0.344,0.281 18 false 14 5.458,1.667 5.729,1.875 0.271,0.208 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

14 HV BATTERY UPPER COVER PANEL G92N1 (Click here) - -
15 BATTERY COOLING BLOWER ASSEMBLY G9230 (Click here) - -
16 REAR FLOOR SIDE MEMBER COVER LH 57628E - - -
17 FRONT FLOOR COVER LH 64740C - - -
18 FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY 51201 - - -
19 HV FLOOR UNDER WIRE 821H1 (Click here) - -

*A for 2WD *B w/ Cover

A490438N01
4.813,1.094 5.292,1.094 false 4.917,2.865 5.396,2.865 false 4.354,4.458 4.604,4.458 false 5.885,4.24 5.885,4.406 false 6.458,0.24 6.802,0.24 false 5.594,3.479 5.906,3.677 0.313,0.198 10 false x5 3.927,3.698 4.208,3.885 0.281,0.188 10 false x6 5.427,0.938 5.969,1.333 0.542,0.396 18 false 20 5.448,2.698 5.99,3.094 0.542,0.396 18 false 21 4.927,4.323 5.469,4.719 0.542,0.396 18 false 22 5.74,4.438 6.49,4.75 0.75,0.313 18 false 23, 25 6.135,0.104 6.677,0.5 0.542,0.396 18 false 24 0.167,0.167 0.708,0.563 0.542,0.396 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

20 DECK BOARD ASSEMBLY 58410B - - -
21 REAR DECK FLOOR BOX 64993 - - -
22 HYBRID INVERTER PROTECTOR ASSEMBLY G92D0 (Click here) - -
23 INVERTER TERMINAL COVER (for AWD) G9223 (Click here) - -
24 TERMINAL VOLTAGE - (Click here) - -
25 TEMPORARILY INSTALL INVERTER TERMINAL COVER (for AWD) G9223 (Click here) - -

*A for AWD - -

A478809N01
3.167,1.208 3.417,1.208 false 2.26,3.115 2.51,3.115 false 1.156,1.333 1.156,1.094 false 1.51,4.948 1.76,4.948 false 6.104,2.49 6.354,2.49 false 4.073,1.677 4.073,1.25 false 3.469,1.094 3.792,1.448 0.323,0.354 18 false 28 2.594,2.979 2.917,3.333 0.323,0.354 18 false 26 1.042,1.406 1.365,1.76 0.323,0.354 18 false 27 3.948,1.74 4.656,2.115 0.708,0.375 18 false 29,32 6.677,2.354 7.156,2.833 0.479,0.479 18 false 30 2.135,4.813 2.615,5.292 0.479,0.479 18 false 30 4.146,0.563 4.469,0.917 0.323,0.354 10 false x5 2.708,0.281 3.031,0.635 0.323,0.354 10 false x2 3.438,5.615 3.802,5.813 0.365,0.198 10 false x4 5.51,5.01 5.875,5.208 0.365,0.198 10 false x2 6.344,3.125 6.708,3.323 0.365,0.198 10 false x4 0.167,0.167 0.875,0.542 0.708,0.375 12 false *A 5.979,1.729 6.344,1.927 0.365,0.198 10 false x4

Procedure Part Name Code
Z101186

Z101188

Z101187

26 REAR SEATBACK ASSEMBLY LH - - - -
27 REAR FLOOR FINISH PLATE 58387B - - -
28 DECK TRIM SIDE PANEL ASSEMBLY LH 64740C - - -
29 REMOVE INVERTER TERMINAL COVER (for AWD) G9223 (Click here) - -
30 HV FLOOR UNDER WIRE 821H1 (Click here) - -
31 HV BATTERY PACK WIRE 821H3 - - -
32 TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY (for AWD) - (Click here) - -

*A for AWD - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for HV Model TMC Made:
(Click here)
for HV Model TMMF Made:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 82121 3.DISCONNECT ENGINE WIRE

Z101186

Click here(Click here)

Hide 4.REMOVE CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 5.CHECK TERMINAL VOLTAGE

Z101186

Click here(Click here)

Hide 6.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 821H1 7.DISCONNECT FLOOR UNDER WIRE

Z101186

Click here(Click here)

Hide 73350C 8.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 9.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 10.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918F 11.REMOVE REAR DOOR SCUFF PLATE INSIDE LH

Hide 76971G 12.REMOVE REAR UNDER COVER

Hide 71403 13.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92N1 14.REMOVE HV BATTERY UPPER COVER PANEL

Z101186

Click here(Click here)

Hide G9230 15.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Hide 57628E 16.REMOVE REAR FLOOR SIDE MEMBER COVER LH (w/ Cover)

a.
A458348


Hide 64740C 17.REMOVE FRONT FLOOR COVER LH

a.
A458349C01
0,0 0,0 false
V100135

Bolt
V100136

Clip



Hide 51201 18.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 821H1 19.REMOVE FLOOR UNDER WIRE (for 2WD)

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



a.
A460052C01
3.75,0.583 4.083,0.583 true 4.125,0.49 4.375,0.677 0.25,0.188 10 true *a 2.219,0.063 2.375,0.344 0.156,0.281 18 true i 3.792,0.177 4.01,0.458 0.219,0.281 18 true ii
*a Shield Ground - -


i.

Disconnect the 2 HV battery junction block assembly and floor wire connectors.


ii.

Disconnect the shield ground from the HV battery.



b.
A461188N03
2.281,0.073 2.448,0.354 0.167,0.281 18 true i 1.531,2 1.75,2.292 0.219,0.292 18 true ii 2.438,3.917 2.677,4.208 0.24,0.292 18 true iii

i.

Remove the 2 nuts.


ii.

Remove the 3 nuts and clamp.

NOTICE:

If the clamps are removed forcibly, the stud bolts may be damaged.



iii.

Disengage the grommet and pull out the HV floor under wire from the floor panel hole.



c.
A462851N01
0.438,0.104 0.604,0.375 0.167,0.271 18 true i 0.427,1.99 0.635,2.26 0.208,0.271 18 true iii 4.094,0.073 4.302,0.344 0.208,0.271 18 true ii

i.

Disengage the 4 clamps.


ii.

Disconnect the HV floor under wire connector.


iii.

Remove the bolt, nut and HV floor under wire.



Hide 58410B 20.REMOVE DECK BOARD ASSEMBLY (for AWD)

Hide 64993 21.REMOVE REAR DECK FLOOR BOX (for AWD)

Hide G92D0 22.REMOVE HYBRID INVERTER PROTECTOR ASSEMBLY (for AWD)

Z101186

Click here(Click here)

Hide G9223 23.REMOVE INVERTER TERMINAL COVER (for AWD)

Z101186

Click here(Click here)

Hide 24.CHECK TERMINAL VOLTAGE (for AWD)

Z101186

Click here(Click here)

Hide G9223 25.TEMPORARILY INSTALL INVERTER TERMINAL COVER (for AWD)

Z101186

Click here(Click here)

Hide 26.REMOVE REAR SEATBACK ASSEMBLY LH (for AWD)

Hide 58387B 27.REMOVE REAR FLOOR FINISH PLATE (for AWD)

Hide 64740C 28.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for AWD)

Hide G9223 29.REMOVE INVERTER TERMINAL COVER (for AWD)

Z101186

Click here(Click here)

Hide 821H1 30.REMOVE FLOOR UNDER WIRE (for AWD)

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



a.
A461188N03
2.281,0.073 2.448,0.354 0.167,0.281 18 true i 1.531,2 1.75,2.292 0.219,0.292 18 true ii 2.438,3.917 2.677,4.208 0.24,0.292 18 true iii

i.

Remove the 2 nuts.


ii.

Remove the 3 nuts and clamp.

NOTICE:

If the clamps are removed forcibly, the stud bolts may be damaged.



iii.

Disengage the grommet and pull out the HV floor under wire from the floor panel hole.



b.
A462851N01
0.438,0.104 0.604,0.375 0.167,0.271 18 true i 0.427,1.99 0.635,2.26 0.208,0.271 18 true iii 4.094,0.073 4.302,0.344 0.208,0.271 18 true ii

i.

Disengage the 4 clamps.


ii.

Disconnect the HV floor under wire connector.


iii.

Remove the bolt, nut and HV floor under wire.



c.
A458353N01
2.24,0.031 2.417,0.333 0.177,0.302 18 true i

i.

Disengage the 3 clamps.



d.
A458336C01
3.125,2 3.458,2 true 2.927,1.927 3.24,2.125 0.313,0.198 10 false *a 0.479,0.073 0.76,0.396 0.281,0.323 18 false i
*a Waterproof Seal - -


i.

Using an insulated tool, remove the 4 bolts and disconnect the HV floor under wire from the rear hybrid motor control inverter assembly.

NOTICE:
·

Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.

·

Do not touch the waterproof seal or terminals of the HV floor under wire.

·

Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.

·

Insulate the disconnected terminals with insulating tape.





Hide 821H3 31.REMOVE HV BATTERY PACK WIRE (for AWD)

Z101186

CAUTION:

Wear insulated gloves.



a.
A460052C01
3.75,0.583 4.083,0.583 true 4.125,0.49 4.375,0.677 0.25,0.188 10 true *a 2.219,0.063 2.375,0.344 0.156,0.281 18 true i 3.792,0.177 4.01,0.458 0.219,0.281 18 true ii
*a Shield Ground - -


i.

Disconnect the 2 HV battery junction block assembly and floor wire connectors.


ii.

Disconnect the shield ground from the HV battery.



b.
A458337C01
3.021,2.094 3.354,2.094 true 3.771,2.385 4.104,2.385 false 2.833,2.031 3.146,2.229 0.313,0.198 10 false *b 4.167,2.313 4.479,2.51 0.313,0.198 10 false *a 0.49,0.073 0.667,0.385 0.177,0.313 18 false i
*a Interlock *b Waterproof Seal


i.

Using an insulated tool, remove the 4 bolts and disconnect the HV battery pack wire from the rear hybrid motor control inverter assembly.

NOTICE:
·

Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.

·

Do not touch the waterproof seal or terminals of the rear traction motor cable.

·

Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.

·

Insulate the disconnected terminals with insulating tape.

·

Make sure to pull the rear traction motor cable out, as a connector is connected to the inside of the inverter terminal cover.





Hide 32.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY (for AWD)

Z101186

Click here(Click here)