Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for LHD) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0480782 BRAKE ACTUATOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C460869N01
5.177,2.281 6.26,2.448 1.083,0.167 1.542,5.448 2.708,5.698 1.167,0.25 5.135,2.24 6.302,2.49 1.167,0.25 1.583,5.49 2.667,5.656 1.083,0.167 4.063,0.729 4.313,0.729 false 2.594,3.281 3.01,3.281 false 4.052,2.135 4.292,1.719 4.292,1.719 4.458,1.719 false 4.927,4.135 5.26,4.135 false 4.917,4.625 5.083,4.625 false 3.927,4.281 4.26,4.281 false 4.167,4.76 4.26,4.76 false 2.969,4.531 3.302,4.531 false 3.094,4.979 3.344,4.979 false 4.833,2.365 5.167,2.365 false 2.677,5.573 4.844,5.573 4.844,5.573 4.844,4.99 false 4.365,5.563 4.365,5.146 false 3.406,5.573 3.406,5.406 false 4.594,0.583 5.146,0.938 0.552,0.354 18 false 3 2.385,3.115 2.938,3.469 0.552,0.354 18 false 4 5.302,3.969 5.854,4.323 0.552,0.354 18 false 1 5.417,4.448 5.969,4.802 0.552,0.354 18 false 2 3.958,4.594 4.51,4.948 0.552,0.354 18 false 2 3.719,4.104 4.271,4.458 0.552,0.354 18 false 1 2.74,4.354 3.292,4.708 0.552,0.354 18 false 1 2.885,4.813 3.438,5.167 0.552,0.354 18 false 2 4.542,1.594 4.854,1.792 0.313,0.198 10 false *1 4.854,2.135 5.167,2.333 0.313,0.198 10 false x3 5.25,2.281 6.417,2.448 1.167,0.167 8 false 5.4 (55, 48 in.*lbf) 1.667,5.49 2.833,5.656 1.167,0.167 8 false 5.4 (55, 48 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE ACTUATOR BRACKET CUSHION 44547B - - -
2 NO. 1 BRAKE ACTUATOR CASE COLLAR 44521A (Click here) - -
3 BRAKE ACTUATOR ASSEMBLY 44510 (Click here) - -
4 NO. 1 BRAKE ACTUATOR BRACKET 44591 (Click here) - -

*1 BRAKE ACTUATOR BRACKET ASSEMBLY - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) - -

C460861N02
5.167,2.646 5.917,2.813 0.75,0.167 6,1.167 6.917,1.5 0.917,0.333 5.958,1.125 6.958,1.542 1,0.417 5.344,0.083 6.26,0.417 0.917,0.333 5.302,0.042 6.302,0.458 1,0.417 5.125,2.604 5.958,2.854 0.833,0.25 2.719,0.115 3.469,0.281 0.75,0.167 2.677,0.073 3.51,0.323 0.833,0.25 2.594,2.542 2.844,2.542 false 4.469,1.615 4.698,2.104 4.698,2.104 4.865,2.104 false 5.25,1.656 5.25,1.323 5.25,1.323 5.417,1.323 false 5.104,1.656 5.104,1.323 5.104,1.323 5.271,1.323 false 4.198,0.552 4.198,0.219 4.198,0.219 4.781,0.219 false 4.26,0.219 4.26,0.521 false 4.333,0.219 4.333,0.49 false 4.406,0.229 4.406,0.479 false 4.833,2.719 5.167,2.719 false 3.479,0.198 3.646,0.198 3.646,0.198 4.063,0.781 false 2.375,2.375 2.927,2.729 0.552,0.354 18 false 7 5.771,1.167 6.323,1.521 0.552,0.354 18 false 6 5.156,1.99 5.708,2.344 0.552,0.354 18 false 5 4.833,2.74 5.146,2.938 0.313,0.198 10 false x2 5.083,0.115 5.635,0.469 0.552,0.354 18 false 6 5.427,0.094 6.333,0.292 0.906,0.198 8 false 15.2 (155, 11) 5.427,0.25 6.333,0.448 0.906,0.198 8 false 13.4 (137, 10)* 6.073,1.323 6.979,1.521 0.906,0.198 8 false 17.4 (177, 13)* 6.073,1.167 6.979,1.365 0.906,0.198 8 false 19.5 (199, 14) 5.219,2.635 6.125,2.833 0.906,0.198 8 false 19 (194, 14) 2.771,0.115 3.677,0.313 0.906,0.198 8 false 19 (194, 14)

Procedure Part Name Code
Z101186

Z101188

Z101187

5 BRAKE ACTUATOR WITH BRACKET - (Click here) - -
6 INSTALL BRAKE LINE - (Click here) - -
7 ENGINE ROOM MAIN WIRE - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) * For use with a union nut wrench

C460870N01
1.104,1.094 2.188,1.26 1.083,0.167 2.344,0.26 2.51,0.26 2.51,0.26 2.781,0.646 false 2.375,2.26 2.542,2.26 2.542,2.26 2.927,1.573 false 3.875,1.448 4.042,1.448 4.042,1.448 4.198,1.656 false 3.906,0.438 4.073,0.438 4.073,0.438 4.229,0.646 false 2.198,1.177 2.531,1.177 false 2.146,0.104 2.427,0.458 0.281,0.354 18 false 9 2.156,2.125 2.604,2.479 0.448,0.354 18 false 8 3.781,0.333 3.938,0.531 0.156,0.198 10 false ● 3.75,1.333 3.906,1.531 0.156,0.198 10 false ● 1.198,1.094 2.292,1.302 1.094,0.208 8 false 9.5 (97, 84 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

8 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY 88710E (Click here) - -
9 SUCTION TUBE SUB-ASSEMBLY B 88707B (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Compressor oil ND-OIL 11 or equivalent - -

C460871N02
1.115,1.385 1.781,1.552 0.667,0.167 2.635,0.583 2.969,0.583 false 3.333,0.938 3.667,0.938 false 5.302,2 5.635,2 false 4.563,3.375 4.896,3.375 false 6.396,1.104 6.729,1.104 false 6.375,0.771 6.708,0.771 false 6.406,0.313 6.74,0.313 false 1.781,1.469 2.115,1.469 false 5.104,0.146 6.385,0.5 1.281,0.354 18 false 16, 18 - 23 6.01,0.615 6.51,1.031 0.5,0.417 18 false 14 4.802,0.969 6.521,1.385 1.719,0.417 18 false 15, 17, 24, 25 5.708,1.844 6.156,2.25 0.448,0.406 18 false 13 3.75,0.802 4.167,1.219 0.417,0.417 18 false 12 3.073,0.417 3.5,0.823 0.427,0.406 18 false 11 4.969,3.229 5.354,3.646 0.385,0.417 18 false 10 2.313,1.365 2.771,1.563 0.458,0.198 10 false x11 1.188,1.385 1.906,1.552 0.719,0.167 8 false 12 (122, 9)

Procedure Part Name Code
Z101186

Z101188

Z101187

10 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
11 WATER GUARD PLATE RH 55734A - - -
12 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
13 WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY - - - -
14 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
15 UPDATE ECU SECURITY KEY - - - (Click here)
16 BLEED BRAKE LINE (Click here) - - -
17 PERFORM INITIALIZATION AND CALIBRATION - - - (Click here)
18 PERFORM TEST MODE INSPECTION (Click here) - - -
19 INSPECT BRAKE ACTUATOR USING GTS (Click here) - - -
20 CHECK AND CLEAR DTCS (Click here) - - -
21 CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (Click here) - - -
22 WARM UP COMPRESSOR (Click here) - - -
23 INSPECT FOR REFRIGERANT LEAK (Click here) - - -
24 PERFORM INITIALIZATION - - - (Click here)
25 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

CAUTION / NOTICE / HINT

NOTICE:

After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

Hide 44521A 2.INSTALL NO. 1 BRAKE ACTUATOR CASE COLLAR

Z101186

NOTICE:

Make sure that the No. 1 brake actuator case collar is in full contact with the brake actuator bracket cushion.



Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

Z101186

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C460863N01
3.01,0.677 3.167,0.875 0.156,0.198 10 true 1 2.948,1.323 3.104,1.521 0.156,0.198 10 false 2 3.104,1.604 3.229,1.76 0.125,0.156 10 false 3 2.365,0.063 2.854,0.385 0.49,0.323 18 false i, ii

i.

Temporarily install the brake actuator assembly with the 3 bolts.


ii.

Fully tighten the 3 bolts in the order shown in the illustration.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)



Hide 44591 4.INSTALL NO. 1 BRAKE ACTUATOR BRACKET

Z101186

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 5.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C460864C02
0.917,0.906 1.073,1.104 0.156,0.198 10 true 1 1.771,1.542 1.927,1.74 0.156,0.198 10 true 3 2.958,1.333 3.115,1.531 0.156,0.198 10 true 2 0.313,0.042 0.813,0.396 0.5,0.354 18 false i, ii 3.979,0.042 4.26,0.396 0.281,0.354 18 false iii
V113147

Move in this Direction - -


i.

Temporarily install the brake actuator with bracket to the vehicle body with the bolt and 2 nuts.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Install the brake actuator with bracket while avoiding the brake lines.



ii.

Fully tighten the bolt and 2 nuts in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


iii.

Return the suction pipe sub-assembly and air conditioner tube and accessory assembly to its original position.

NOTICE:

Do not apply excessive force to the suction pipe sub-assembly and air conditioner tube and accessory assembly.




Hide 6.INSTALL BRAKE LINE

a.
C460865C01
1.667,1.979 1.573,1.656 true 1.792,1.323 2.313,1.198 true 0.948,1.854 1.292,1.542 true 0.896,1.323 1.365,1.396 true 0.938,0.969 1.448,1.229 true 1.646,1.073 2.115,0.74 true 2.365,1.094 2.563,1.302 0.198,0.208 10 true *a 1.604,2.021 1.854,2.188 0.25,0.167 10 true *b 2.156,0.625 2.396,0.823 0.24,0.198 10 true *c 0.708,0.844 0.927,1.021 0.219,0.177 10 true *d 0.677,1.208 0.875,1.417 0.198,0.208 10 true *e 0.802,1.917 0.958,2.115 0.156,0.198 10 true *f 5.083,1.396 5.229,1.573 0.146,0.177 10 true B 5.49,1.083 5.635,1.26 0.146,0.177 10 true B 4.76,1.313 4.906,1.49 0.146,0.177 10 true A 4.677,0.635 4.823,0.813 0.146,0.177 10 true A 4.792,0.396 4.938,0.573 0.146,0.177 10 true A 5.594,0.51 5.74,0.688 0.146,0.177 10 true A 0.344,0.573 0.625,0.927 0.281,0.354 18 false i 4,0.083 4.281,0.438 0.281,0.354 18 false ii 5.635,2.458 5.896,2.708 0.26,0.25 10 false *g
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH *d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH *f To Front Wheel Cylinder Assembly RH
*g Torque Wrench Fulcrum Length - -


i.

Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.


ii.

Using a union nut wrench, fully tighten the 6 brake lines.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)





Hide 7.CONNECT ENGINE ROOM MAIN WIRE

a.
C460866C01
1.854,0.052 2.135,0.406 0.281,0.354 18 false i
V113147

Connect the connector
V113148

Lock the lock lever


i.

Connect the connector to the brake actuator assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.





Hide 88710E 8.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.
C460867C01
0.313,0.063 0.958,0.396 0.646,0.333 18 false i, ii 4.094,1 4.375,1.354 0.281,0.354 18 false v 0.313,0.99 0.594,1.344 0.281,0.354 18 false iv 3.979,0.052 4.26,0.406 0.281,0.354 18 false iii
V100135

Compressor Oil
V113147

Install in this Direction


i.

Remove the vinyl tape from the air conditioning tube and accessory assembly.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.

Compressor Oil:

ND-OIL 11 or equivalent



iii.

Install the O-ring to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



iv.

Connect the air conditioning tube and accessory assembly to the air conditioning unit assembly.


v.

Engage the clamp to install the air conditioning tube and accessory assembly.



Hide 88707B 9.INSTALL SUCTION TUBE SUB-ASSEMBLY B

a.
C460868C01
0.313,0.052 0.865,0.406 0.552,0.354 18 false i, ii 3.958,0.042 4.51,0.396 0.552,0.354 18 false iii 0.344,1.021 0.896,1.375 0.552,0.354 18 false iv 4,1.01 4.552,1.365 0.552,0.354 18 false v 2.219,3.01 2.906,3.365 0.688,0.354 18 true vi, vii
V100135

Compressor Oil
V113147

Rotate in this Direction


i.

Remove the vinyl tape from the suction tube sub-assembly B.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction tube sub-assembly B.

Compressor Oil:

ND-OIL 11 or equivalent



iii.

Install the O-ring to the suction tube sub-assembly B.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



iv.

Connect the suction tube sub-assembly B to the air conditioning unit assembly.


v.

Engage the clamp to install the suction tube sub-assembly B.


vi.

Rotate the hook connector as shown in the illustration.


vii.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)



Hide 55701J 10.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55734A 11.INSTALL WATER GUARD PLATE RH

Hide 55815E 12.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 13.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 21.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 24.PERFORM INITIALIZATION


HINT:

The parking brake indicator light blinks (red) when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.


Hide 25. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART