| *1 | BRAKE ACTUATOR BRACKET ASSEMBLY | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 5 | BRAKE ACTUATOR WITH BRACKET | - | ( )
|
- | - |
| 6 | BRAKE LINE | - | ( )
|
- | - |
| 7 | ENGINE ROOM MAIN WIRE | - | ( )
|
- | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | * | For use with a union nut wrench or SST |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.
44547B
1.INSTALL BRAKE ACTUATOR BRACKET CUSHION
44521A
2.INSTALL NO. 1 BRAKE ACTUATOR CASE COLLAR
|
|
44510
3.INSTALL BRAKE ACTUATOR ASSEMBLY
|
|
Temporarily install the brake actuator assembly with the 3 bolts.
Fully tighten the 3 bolts in the order shown in the illustration.
44591
4.INSTALL NO. 1 BRAKE ACTUATOR BRACKET
|
|
5.INSTALL BRAKE ACTUATOR WITH BRACKET
| *a | Torque Wrench Fulcrum Length | - | - |
Temporarily install the brake actuator with bracket to the vehicle body with the bolt and 2 nuts.
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Be careful not to allow any brake fluid to enter the connector.
Do not hold the brake actuator assembly by the connector.
Do not drop the brake actuator with bracket when carrying it.
Install the brake actuator with bracket while avoiding the brake lines.
Using SST, fully tighten the bolt and 2 nuts in the order shown in the illustration.
Do not damage the brake lines.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using SST (fulcrum length of 200 mm (7.87 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
8.5 N*m (87 kgf*cm, 75 in.*lbf)
6.INSTALL BRAKE LINE
| *a | From 1st Chamber of Brake Booster with Master Cylinder Assembly | *b | From 2nd Chamber of Brake Booster with Master Cylinder Assembly |
| *c | To Front Wheel Cylinder Assembly LH | *d | To Rear Wheel Cylinder Assembly RH |
| *e | To Rear Wheel Cylinder Assembly LH | *f | To Front Wheel Cylinder Assembly RH |
| *g | Torque Wrench Fulcrum Length | - | - |
Temporarily tighten each brake line to the correct position on the brake actuator assembly as shown in the illustration.
Using a 10 mm and 12 mm union nut wrench, connect the 6 brake lines to the brake actuator assembly.
Do not kink or damage the brake lines.
Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
(A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
(B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)
Using a 10 mm union nut wrench, connect the brake line to the front flexible hose.
Do not kink or damage the brake lines.
Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
7.CONNECT ENGINE ROOM MAIN WIRE
|
Connect the connector |
|
Lock the lock lever |
Connect the connector to the brake actuator assembly and lock the lock lever as shown in the illustration.
Make sure that the connector is locked securely.
Make sure that the connector can be connected smoothly.
Do not allow water, oil or dirt to enter the connector.
74404A
8.INSTALL BATTERY CLAMP SUB-ASSEMBLY
17701
9.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17801
10.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
89661
12.INSTALL ECM
55701J
13.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
55735A
14.INSTALL WATER GUARD PLATE LH
55815E
15.INSTALL FRONT NO. 1 VENTILATOR SEAL
16.INSTALL WINDSHIELD WIPER MOTOR AND LINK
17.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
18. UPDATE ECU SECURITY KEY
19.BLEED BRAKE SYSTEM
20.PERFORM INITIALIZATION AND CALIBRATION
21.PERFORM TEST MODE INSPECTION
22.INSPECT BRAKE ACTUATOR USING GTS
23.PERFORM INITIALIZATION
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model TMMF Made)>PRECAUTION
The parking brake indicator light blinks (red) when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.
24. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
25. CHECK FOR AND CLEAR DTCS