Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for HV Model LHD) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480839 BRAKE PEDAL(for HV Model LHD) A

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for HV Model LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C460919N01
0.667,1.917 1.5,2.083 0.833,0.167 0.625,1.875 1.542,2.125 0.917,0.25 0.99,3.542 1.823,3.708 0.833,0.167 0.948,3.5 1.865,3.75 0.917,0.25 2.063,4.854 2.896,5.021 0.833,0.167 2.021,4.813 2.938,5.063 0.917,0.25 3.542,0.594 3.875,0.594 false 5.104,1.354 5.5,1.354 false 4.896,1.677 5.115,1.865 5.115,1.865 5.281,1.865 false 1.5,2 1.833,2 false 1.865,4.104 2.198,4.104 false 1.823,3.625 2.156,3.625 false 1.625,4.365 2.021,4.365 false 5.104,3.01 5.531,3.01 false 3.792,4.177 4.302,4.177 false 6.063,4.479 6.49,4.479 false 3.385,4.896 3.385,5.177 false 3.354,4.531 3.063,4.938 3.063,4.938 2.896,4.938 false 3.906,0.49 4.219,0.688 0.313,0.198 10 false *1 5.823,1.188 6.135,1.583 0.313,0.396 18 false 6 5.49,1.688 5.802,2.083 0.313,0.396 18 false 5 5.354,1.76 5.667,1.958 0.313,0.198 10 false ● 5.833,2.844 6.146,3.24 0.313,0.396 18 false 3 4.625,4.021 4.938,4.417 0.313,0.396 18 false 2 6.5,4.313 6.813,4.708 0.313,0.396 18 false 1 1.417,4.188 1.729,4.583 0.313,0.396 18 false 4 1.729,4 2.042,4.198 0.313,0.198 10 false ● 3.344,5.177 3.656,5.375 0.313,0.198 10 false ● 2.302,3.563 2.615,3.76 0.313,0.198 10 false x2 3.469,4.417 3.781,4.615 0.313,0.198 10 false x2 3.49,4.802 3.802,5 0.313,0.198 10 false x2 0.719,1.906 1.625,2.219 0.906,0.313 8 false 17.5 (178, 13) 1.073,3.552 1.979,3.865 0.906,0.313 8 false 12.7 (130, 9) 2.146,4.844 3.052,5.156 0.906,0.313 8 false 12.7 (130, 9)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE PEDAL PAD 47121 - - -
2 BRAKE PEDAL SUPPORT ASSEMBLY 47110 (Click here) - -
3 PUSH ROD PIN 47264A (Click here) - -
4 BRAKE PEDAL RETURN SPRING 47101A (Click here) - -
5 STOP LIGHT SWITCH MOUNTING ADJUSTER 84345 - - -
6 STOP LIGHT SWITCH ASSEMBLY 84340 (Click here) - -

*1 ENGINE ROOM MAIN WIRE - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) ● Non-reusable part
V100135

Lithium soap base glycol grease - -

C460920N02
0.115,3.552 1.115,3.719 1,0.167 0.073,3.51 1.156,3.76 1.083,0.25 0.354,0.26 0.823,0.26 false 0.406,0.708 0.823,0.708 false 4.771,0.688 5.188,0.688 false 1.792,2.823 2.177,2.823 false 0.615,3.198 0.615,3.542 false 4.573,0.531 4.854,0.885 0.281,0.354 18 false 9 0.906,0.094 1.865,0.438 0.958,0.344 18 false 7, 12 0.865,0.542 1.823,0.885 0.958,0.344 18 false 10, 11 2.469,2.667 2.75,3.021 0.281,0.354 18 false 8 0.708,3.104 0.99,3.375 0.281,0.271 10 false x2 0.156,3.552 1.427,3.771 1.271,0.219 8 false 8.5 (87, 75 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

7 INSPECT AND ADJUST BRAKE PEDAL - (Click here) - -
8 BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D (Click here) - -
9 STEERING COLUMN ASSEMBLY - - - -
10 PERFORM INITIALIZATION AND CALIBRATION - - - (Click here)
11 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)
12 CHECK FOR AND CLEAR DTCS - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) - -

PROCEDURE

Hide 47121 1.INSTALL BRAKE PEDAL PAD

Hide 47110 2.INSTALL BRAKE PEDAL SUPPORT ASSEMBLY

a.
C460916N02
0.24,0.146 0.521,0.5 0.281,0.354 18 false i 3.854,0.146 4.667,0.448 0.813,0.302 18 true ii, iii, iv 2.01,1.99 2.531,2.448 0.521,0.458 18 false v 6,0.406 6.156,0.604 0.156,0.198 10 true 4 6.323,1.094 6.479,1.292 0.156,0.198 10 true 1 4.979,1.115 5.135,1.313 0.156,0.198 10 true 2 4.688,0.51 4.844,0.708 0.156,0.198 10 true 3

i.

Engage the 3 clamps to install the wire harness to the brake pedal support assembly.


ii.

Temporarily install the brake pedal support assembly with the 2 bolts and 2 nuts.


iii.

Tighten the 2 nuts and 2 bolts in the order shown in the illustration.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


iv.

Install 2 new clips.


v.

Engage the clamp to install the wire harness to the brake pedal support assembly.



Hide 47264A 3.INSTALL PUSH ROD PIN

a.
C460917C01
0.375,0.021 0.656,0.375 0.281,0.354 18 false i 3.729,0.01 4.01,0.365 0.281,0.354 18 false ii
V100135

Lithium soap base glycol grease - -


i.

Apply lithium soap base glycol grease to the push rod pin and installation hole of the brake pedal support assembly.


ii.

Connect the brake master cylinder push rod clevis to the brake pedal support assembly with the push rod pin, and install a new clip.

NOTICE:

Be sure to install the push rod pin in the correct direction.




Hide 47101A 4.INSTALL BRAKE PEDAL RETURN SPRING

a.
C460918N01
1.698,0.063 1.979,0.417 0.281,0.354 18 false i

i.

Install the brake pedal return spring to the brake pedal support assembly as shown in the illustration.



Hide 84345 5.INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER

Hide 84340 6.INSTALL STOP LIGHT SWITCH ASSEMBLY

Z101186

Click here(Click here)

Hide 89510D 8.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

Z101186

Click here(Click here)

Hide 9.INSTALL STEERING COLUMN ASSEMBLY

Hide 11. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART