Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for HV Model RHD) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480840 BRAKE PEDAL(for HV Model RHD) A

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for HV Model RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C461345N01
2.771,1.313 4.667,4.094 1.896,2.781 2.771,2.677 4.667,2.677 false 3.052,2.073 3.125,2.365 3.125,2.365 3.292,2.365 false 3.396,3.448 3.406,3.844 3.406,3.844 3.573,3.844 false 3.708,0.76 4.135,0.76 false 3.542,0.583 3.823,0.938 0.281,0.354 18 false 1 2.823,1.333 3.104,1.615 0.281,0.281 12 false *A 2.823,2.729 3.115,3 0.292,0.271 12 false *B 3.635,2.198 3.917,2.552 0.281,0.354 18 false 2 3.875,3.688 4.156,4.042 0.281,0.354 18 false 2 3.875,1.833 4.156,2.188 0.281,0.354 10 false x2 4.458,3.083 4.74,3.438 0.281,0.354 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING COLUMN ASSEMBLY - - - -
2 BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D (Click here) - -

*A for TMC Made *B for TMMF Made

C460921N01
2.927,0.5 3.094,0.5 3.094,0.5 3.26,0.771 false 4.948,1 5.281,1 false 4.771,1.417 5.01,1.417 false 4.813,3.438 5.146,3.438 false 5.573,4.927 5.906,4.927 false 3.521,4.323 3.854,4.323 false 2.865,4.635 3.198,4.635 false 1.604,3.938 1.938,3.938 false 2.042,3.594 2.208,3.594 2.208,3.594 2.375,3.865 false 5.333,0.844 5.615,1.198 0.281,0.354 18 false 3 5.427,1.229 5.708,1.583 0.281,0.354 18 false 4 5.292,1.292 5.573,1.646 0.281,0.354 10 false ● 5.198,3.271 5.479,3.625 0.281,0.354 18 false 6 5.969,4.76 6.25,5.115 0.281,0.354 18 false 9 3.896,4.167 4.177,4.521 0.281,0.354 18 false 8 1.406,3.771 1.688,4.125 0.281,0.354 18 false 5 2.76,0.323 3.042,0.677 0.281,0.354 18 false 7 2.771,2.99 3.021,3.26 0.25,0.271 10 false x2 3.219,4.646 3.469,4.917 0.25,0.271 10 false x2 1.917,3.49 2.198,3.844 0.281,0.354 10 false ● 4.281,3.896 4.531,4.167 0.25,0.271 10 false x2 2.719,4.521 3,4.875 0.281,0.354 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

3 STOP LIGHT SWITCH ASSEMBLY 84340 - - -
4 STOP LIGHT SWITCH MOUNTING ADJUSTER 84345 (Click here) - -
5 BRAKE PEDAL RETURN SPRING 47101A - - -
6 PUSH ROD PIN 47264A - - -
7 ENGINE ROOM MAIN WIRE - - - -
8 BRAKE PEDAL SUPPORT ASSEMBLY 47110 - - -
9 BRAKE PEDAL PAD 47121 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake pedal support assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Replacement of brake pedal support assembly
for TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


for TMMF Made:
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)

NOTICE:
·

When disassembling the brake pedal support assembly, do not loosen the breakaway bolt at the time of collisions.

·

If the breakaway bolt at the time of collisions is loosened, replace with a new brake pedal support assembly.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE STEERING COLUMN ASSEMBLY

Hide 89510D 2.REMOVE BRAKE PEDAL STROKE SENSOR ASSEMBLY

Z101186

·

for TMC Made:

Click here(Click here)

·

for TMMF Made:

Click here(Click here)



Hide 84340 3.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 84345 4.REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER

Z101186

Click here(Click here)

Hide 47101A 5.REMOVE BRAKE PEDAL RETURN SPRING

a.
C461356


Hide 47264A 6.REMOVE PUSH ROD PIN

a.
C429618


Hide 7.SEPARATE ENGINE ROOM MAIN WIRE

a.
C429620


Hide 47110 8.REMOVE BRAKE PEDAL SUPPORT ASSEMBLY

a.
C429622


Hide 47121 9.REMOVE BRAKE PEDAL PAD

a.
C430392