Home › Suspension › REAR SUSPENSION › REAR AXLE BEAM › from 2021.07
RM3700E _53 Suspension _093739 REAR SUSPENSION _0441862 REAR AXLE BEAM A

REAR SUSPENSION  REAR AXLE BEAM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C444410N02
2.906,4.646 3.219,4.646 false 5.823,3.896 6.135,3.896 false 5.344,2.708 5.688,2.708 false 4.906,1.667 5.25,1.667 false 3.219,2.885 3.521,2.531 3.521,2.531 3.688,2.531 false 3.563,1.719 3.688,1.25 3.688,1.25 3.854,1.25 false 2.646,0.729 2.99,0.729 false 1.24,1.313 1.583,1.313 false 1.615,1.188 1.896,1.542 0.281,0.354 18 false 3 2.458,0.552 2.74,0.906 0.281,0.354 18 false 5 4.135,1.083 4.417,1.438 0.281,0.354 18 false 6 5.344,1.49 5.625,1.844 0.281,0.354 18 false 4 3.969,2.354 4.25,2.708 0.281,0.354 18 false 7 5.99,2.542 6.271,2.896 0.281,0.354 18 false 6 6.167,3.76 6.448,4.115 0.281,0.354 18 false 2 3.302,4.458 3.583,4.813 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR WHEEL - - - -
2 REAR AXLE HUB AND BEARING ASSEMBLY LH 42450B - - -
3 REAR AXLE HUB AND BEARING ASSEMBLY RH 42450A - - -
4 REAR LOWER COIL SPRING INSULATOR LH 48258C - - -
5 REAR LOWER COIL SPRING INSULATOR RH 48258B - - -
6 REAR SHOCK ABSORBER - (Click here) - -
7 REAR AXLE BEAM ASSEMBLY 42110F (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear axle beam assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for HV Model:
Auxiliary battery terminal is disconnected/reconnected
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Rear wheel alignment adjustment for HV Model TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for HV Model TMMF Made:
1.

Perform "Reset Memory"

2.

Perform calibration (brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
w/ Advanced Park:

Advanced Park


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system w/o Advanced Park:
(Click here)
w/ Advanced Park:
(Click here)
w/ Advanced Park:

Advanced Park


(Click here)

HINT:
for HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 42450B 2.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH

Hide 42450A 3.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 48258C 4.REMOVE REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 5.REMOVE REAR LOWER COIL SPRING INSULATOR RH

a.

Perform the same procedure as for the LH side.


Hide 6.SEPARATE REAR SHOCK ABSORBER

Z101186

CAUTION:

Make sure to secure the rear axle beam assembly to prevent it from dropping.



a.
C443672N01
0.385,0.052 0.802,0.365 0.417,0.313 18 true i, ii

i.

Support the rear axle beam assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools as shown in the illustration.


ii.

Remove the 2 bolts and 2 nuts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

NOTICE:

Because the nuts have their own stoppers, do not turn the nuts. Loosen the bolts with the nuts secured.




Hide 42110F 7.REMOVE REAR AXLE BEAM ASSEMBLY

a.
C443673N01
0.417,0.083 0.698,0.396 0.281,0.313 18 true i

i.

Remove the 2 bolts and rear axle beam assembly.