Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for M15A-FKS TMMF Made) › from 2021.07
RM3700E _52 Drivetrain _094372 DRIVE SHAFT / PROPELLER SHAFT _0481083 FRONT DRIVE SHAFT ASSEMBLY(for M15A-FKS TMMF Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for M15A-FKS TMMF Made)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C462324N01
1.26,2.188 1.542,2.188 false 4.948,3.385 5.281,3.385 false 3.323,3.896 3.656,3.896 false 0.76,3.875 0.76,3.542 false 6.458,0.219 6.792,0.219 false 1.438,4.208 1.75,4.406 0.313,0.198 10 false x4 2.01,4.344 2.323,4.542 0.313,0.198 10 false x4 2.49,4.208 2.802,4.406 0.313,0.198 10 false x9 0.948,1.573 1.26,1.771 0.313,0.198 10 false x2 5.313,0.094 5.51,0.365 0.198,0.271 18 true 5 4.781,3.24 5.094,3.646 0.313,0.406 18 false 1 3.156,3.76 3.479,4.167 0.323,0.406 18 false 3 4.479,3.76 4.792,3.958 0.313,0.198 10 false x2 0.688,3.906 1.146,4.313 0.458,0.406 18 false 2 1.594,2.031 2.052,2.438 0.458,0.406 18 false 4 5.833,0.094 6.375,0.417 0.542,0.323 18 false , 6 5.51,0.125 5.823,0.354 0.313,0.229 12 true (*A) 6.156,0.125 6.542,0.354 0.385,0.229 12 false (*B)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT WHEELS - - - -
2 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
3 REAR ENGINE UNDER COVER LH 51442C - - -
4 REAR ENGINE UNDER COVER RH 51441C - - -
5 DRAIN MANUAL TRANSAXLE OIL - - (Click here) -
6 DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID - - (Click here) -

*A for Manual Transaxle *B for CVT

C462326N01
5.688,2.771 6.021,2.771 false 5.26,2.563 5.594,2.563 false 1.958,0.698 2.292,0.698 false 1.729,1.635 2.063,1.635 false 2.813,3.698 3.146,3.698 false 4.542,0.5 4.875,0.5 false 5.781,1.823 6.115,1.823 false 4.885,3.198 4.885,3.531 false 5.385,0.688 5.719,0.688 false 1.438,1.479 1.813,1.823 0.375,0.344 18 false 13 2.521,3.552 2.885,3.906 0.365,0.354 18 false 12 1.688,0.542 2.031,0.896 0.344,0.354 18 false 11 6.385,1.708 6.771,2.063 0.385,0.354 18 false 10 6.073,2.646 6.354,3 0.281,0.354 18 false 9 5.188,0.375 5.469,0.729 0.281,0.354 18 false 8 5.063,3.49 5.344,3.844 0.281,0.354 18 false 7 4.021,4.281 4.333,4.479 0.313,0.198 10 false x2 5.125,2.469 5.281,2.667 0.156,0.198 10 false ● 4.927,3.521 5.083,3.719 0.156,0.198 10 false ● 5.76,0.594 6.073,0.792 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

7 FRONT AXLE SHAFT NUT 43502H (Click here) - -
8 FRONT SPEED SENSOR 89543 (Click here) - -
9 STEERING KNUCKLE SEAL 43215 - - -
10 TIE ROD END SUB-ASSEMBLY 45047 (Click here) - -
11 FRONT STABILIZER LINK ASSEMBLY 48810 (Click here) - -
12 FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY 48069 - - -
13 DISCONNECT FRONT DRIVE SHAFT ASSEMBLY 43420 (Click here) - -

*1 FRONT FLEXIBLE HOSE - -
● Non-reusable part - -

C462328N01
0.083,0.083 7.083,2.417 7,2.333 0.083,2.417 7.083,4.75 7,2.333 3.646,3.26 3.979,3.26 false 4.406,4.156 4.667,3.792 4.667,3.792 4.833,3.792 false 3.656,0.875 3.99,0.875 false 4.406,1.771 4.667,1.406 4.667,1.406 4.833,1.406 false 0.167,0.167 0.542,0.406 0.375,0.24 12 false *A 0.167,2.5 0.542,2.74 0.375,0.24 12 false *B 4.406,0.729 4.75,1.073 0.344,0.344 18 false 15 5.125,1.292 5.5,1.646 0.375,0.354 18 false 14 4.292,0.781 4.448,0.979 0.156,0.198 10 false ● 4.302,3.177 4.458,3.375 0.156,0.198 10 false ● 4.417,3.125 4.771,3.479 0.354,0.354 18 false 15 5.125,3.667 5.51,4.021 0.385,0.354 18 false 14

Procedure Part Name Code
Z101186

Z101188

Z101187

14 REMOVE FRONT DRIVE SHAFT ASSEMBLY 43420 (Click here) - -
15 FRONT DRIVE SHAFT HOLE SNAP RING 43420G (Click here) - -

*A for Manual Transaxle *B for CVT
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front drive shaft assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (w/o Advanced Park) (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEELS

Hide 51410 2.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442C 3.REMOVE ENGINE UNDER COVER LH

Hide 51441C 4.REMOVE ENGINE UNDER COVER RH

a.

Perform the same procedure as for the LH side.


Hide 5.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 6.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 43502H 7.REMOVE FRONT AXLE SHAFT NUT

a.
C446084N01
2.104,1.563 2.406,1.167 true 0.396,0.073 0.625,0.396 0.229,0.323 18 false i 3.667,0.031 3.854,0.354 0.188,0.323 18 true ii 1.927,1.604 2.292,1.771 0.365,0.167 10 true SST

i.

Using SST and a hammer, release the staked part of the front axle shaft nut.

SST
09930-00010  

NOTICE:

Loosen the staked part of the front axle shaft nut completely, otherwise the threads of the drive shaft may be damaged.



ii.

Using a 30 mm deep socket wrench, remove the front axle shaft nut while applying the brakes.



Hide 89543 8.SEPARATE FRONT SPEED SENSOR

Z101186

Click here(Click here)

Hide 43215 9.REMOVE STEERING KNUCKLE SEAL

Hide 45047 10.SEPARATE TIE ROD END SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 48810 11.SEPARATE FRONT STABILIZER LINK ASSEMBLY

Z101186

Click here(Click here)

Hide 48069 12.SEPARATE FRONT LOWER NO.1 SUSPENSION ARM SUB-ASSEMBLY

Hide 43420 13.DISCONNECT FRONT DRIVE SHAFT ASSEMBLY

a.
C463080C01
2.885,0.76 3.073,0.854 3.073,0.854 2.979,1.01 true 3.083,0.75 3.281,0.948 0.198,0.198 10 true *a 0.396,0.052 0.615,0.333 0.219,0.281 18 false i 3.979,0.052 4.208,0.344 0.229,0.292 18 false ii
*a Matchmark - -


i.

Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.


ii.

Using a plastic hammer, disconnect the front drive shaft assembly from the front axle assembly.

NOTICE:
·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

·

Check that there is no foreign matter on the deflector or contact surfaces.

·

Do not damage the front axle outboard joint boot.

·

Do not damage the front disc brake dust cover.

·

Do not damage the deflector.



HINT:

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.




Hide 43420 14.REMOVE FRONT DRIVE SHAFT ASSEMBLY

a.
C445399N01
3.865,1.302 3.198,1.542 3.198,1.542 3.771,0.906 true 0.469,0.083 0.75,0.438 0.281,0.354 18 false i 2.854,1.479 3.167,1.667 0.313,0.188 10 true SST

i.

Using SST, remove the front drive shaft assembly.

SST
09520-01011  
09520-20010  (09521-02010, 09521-02040, 09521-02060)

NOTICE:
·

Do not damage the front drive shaft oil seal.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly.





Hide 43420G 15.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING

a.
C445400N01
0.406,0.083 0.688,0.438 0.281,0.354 18 false i

i.

Using a screwdriver, remove the front drive shaft hole snap ring.