The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front axle hub bolt replacement are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION (for HV Model TMC Made)
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2. DISABLE BRAKE CONTROL (for HV Model TMC Made)
3.REMOVE FRONT WHEEL
4.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY
Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.
Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging by the front flexible hose.
43512
5.REMOVE FRONT DISC
for TMC Made:
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMC Made)>REMOVAL
for TMMF Made:
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMMF Made)>REMOVAL
43502D
6.REMOVE FRONT AXLE HUB BOLT
| *a | Service Nut |
| *b | Hold |
| *c | Turn |
Temporarily install 2 service nuts to the front axle hub bolts as shown in the illustration.
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Install the service nuts to prevent damage to the front axle hub bolts.
Using SST and a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, remove the front axle hub bolt.
Do not damage the threads of the front axle hub bolts.
43502D
7.INSTALL FRONT AXLE HUB BOLT
Temporarily install a new front axle hub bolt to the front axle hub sub-assembly.
| *a | Service Nut |
| *b | Washer |
| *c | Hold |
| *d | Turn |
Install a washer and service nut to the front axle hub bolt as shown in the illustration.
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Recommended washer thickness is 5 mm (0.197 in.) or more.
Using a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, install the front axle hub bolt by tightening the service nut.
Install the service nuts to prevent damage to the front axle hub bolts.
Do not damage the threads of the front axle hub bolts.
Remove the 3 service nuts and washer from the 3 front axle hub bolts.
43512
8.INSTALL FRONT DISC
for TMC Made:
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMC Made)>INSTALLATION
for TMMF Made:
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMMF Made)>INSTALLATION
9.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.
Do not twist the front flexible hose when installing the front disc brake caliper assembly.
Make sure that there is no foreign matter on the threads of the bolt.
10.INSTALL FRONT WHEEL
11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model TMC Made)
12. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (for HV Model TMC Made)
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART