Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB (for AWD) › from 2021.07
RM3700E _52 Drivetrain _093736 AXLE AND DIFFERENTIAL _0441828 REAR AXLE HUB(for AWD) A

AXLE AND DIFFERENTIAL  REAR AXLE HUB(for AWD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C462680N01
0.646,0.438 1.385,0.604 0.74,0.167 0.604,0.396 1.438,0.646 0.833,0.25 2.281,0.76 3.115,0.927 0.833,0.167 0.552,3.052 1.552,3.219 1,0.167 5.083,2.854 6,3.021 0.917,0.167 2.24,0.719 3.156,0.969 0.917,0.25 0.51,3.01 1.594,3.26 1.083,0.25 5.042,2.813 6.042,3.063 1,0.25 4.885,1.615 5.344,1.615 false 4.917,3.583 4.917,2.938 4.917,2.938 5.083,2.938 false 5.677,5.427 5.844,5.427 5.844,5.427 5.969,5.094 false 1.479,2.469 1.667,2.938 1.667,2.938 1.823,2.938 false 3.74,1.042 4.073,1.042 false 0.313,0.969 0.5,0.521 0.5,0.521 0.646,0.521 false 1.979,1.281 2.135,0.844 2.135,0.844 2.281,0.844 false 3.729,4.031 3.896,4.031 3.896,4.031 4.167,3.635 false 1.042,2.531 1.042,3.052 false 3.583,2.333 3.917,2.333 false 2.448,2.396 2.448,2.594 false 6.385,1.01 6.719,1.01 false 6.375,0.208 6.708,0.208 false 6.375,0.615 6.708,0.615 false 5.625,1.479 6.823,1.802 1.198,0.323 18 false 3, 5, 12 6.51,2.802 7.031,3.146 0.521,0.344 18 false 4, 9 4.833,5.292 5.802,5.615 0.969,0.323 18 false 2, 6, 11 3.958,2.24 4.333,2.406 0.375,0.167 10 false *1 2.094,2.802 2.406,3.115 0.313,0.313 18 false 10 2.094,1.219 2.469,1.385 0.375,0.167 10 false x2 0.427,0.906 0.802,1.073 0.375,0.167 10 false x4 3.438,0.906 3.813,1.188 0.375,0.281 18 false 13 3.573,3.885 3.792,4.188 0.219,0.302 18 false 1 5.76,0.5 6.135,0.792 0.375,0.292 18 false 14 5.5,0.073 6.49,0.417 0.99,0.344 18 false 7, 8, 15 2.333,0.771 3.417,1.01 1.083,0.24 8 false 107 (1091, 79) 0.594,3.052 1.781,3.302 1.188,0.25 8 false 8.5 (87, 75 in.*lbf) 5.146,2.865 6.083,3.104 0.938,0.24 8 false 216 (2203, 159) 2.385,2.615 2.729,2.875 0.344,0.26 10 false *2 6.385,2.865 6.594,3.115 0.208,0.25 10 false ● 0.708,0.448 1.51,0.656 0.802,0.208 8 false 90 (918, 66) 5.771,0.896 6.115,1.208 0.344,0.313 18 false 16 6.063,0.552 6.469,0.833 0.406,0.281 12 false (*A) 6.073,0.938 6.458,1.198 0.385,0.26 12 false (*A)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR AXLE HUB AND BEARING ASSEMBLY 42450B (Click here) - -
2 INSTALL REAR DISC 42431 (Click here) - -
3 INSTALL REAR DISC BRAKE CALIPER ASSEMBLY - (Click here) - -
4 INSTALL REAR AXLE SHAFT NUT 42312B (Click here) - -
5 SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY - (Click here) - -
6 REMOVE REAR DISC 42431 (Click here) - -
7 INSPECT REAR AXLE HUB BEARING LOOSENESS - (Click here) - -
8 INSPECT REAR AXLE HUB RUNOUT - (Click here) - -
9 STAKE REAR AXLE SHAFT NUT 42312B (Click here) - -
10 REAR SKID CONTROL SENSOR 89544E (Click here) - -
11 INSTALL REAR DISC 42431 (Click here) - -
12 INSTALL REAR DISC BRAKE CALIPER ASSEMBLY - (Click here) - -
13 PARKING BRAKE ACTUATOR ASSEMBLY 46310B - - -
14 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
15 CHECK FOR SPEED SENSOR SIGNAL - (Click here) - -
16 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

*A for TMC Made - -
*1 REAR BRAKE DUST COVER *2 REAR AXLE BEARING RETAINER
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) ● Non-reusable part
V103638

Do not apply lubricants to the threaded parts - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42450B 1.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

a.
C444364C01
2.708,0.354 3.052,0.438 3.052,0.438 2.823,0.625 true 0.406,0.063 0.688,0.417 0.281,0.354 18 false i 3.698,0.073 3.979,0.427 0.281,0.354 18 false ii 3.083,0.365 3.271,0.542 0.188,0.177 10 true *a
*a Matchmark - -


i.

Align the matchmarks on the rear drive shaft assembly and rear axle hub and bearing assembly.

NOTICE:

Be careful not to damage the thread portion of the rear drive shaft assembly.



ii.

Install the rear axle hub and bearing assembly, rear axle bearing retainer and rear disc brake dust cover to the rear axle carrier sub-assembly with the 4 bolts.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)

NOTICE:

Do not damage the rear drive shaft outboard joint boot.




Hide 42431 2.INSTALL REAR DISC

Z101186

Click here(Click here)

Hide 3.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

Z101186

Click here(Click here)

Hide 42312B 4.INSTALL REAR AXLE SHAFT NUT

a.
C444365N01
0.385,0.063 0.667,0.417 0.281,0.354 18 false i 3.938,0.073 4.219,0.427 0.281,0.354 18 false ii

i.

Clean the threaded parts on the rear drive shaft assembly and a new rear axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new rear drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




ii.

Using a 30 mm deep socket wrench, install the rear axle shaft nut while applyingthe brakes.

Torque:
216 N*m (2203 kgf*cm, 159 ft.*lbf)

NOTICE:

Stake the rear axle shaft nut after inspecting for looseness and runout in the following steps.




Hide 5.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Z101186

Click here(Click here)

Hide 42431 6.REMOVE REAR DISC

Z101186

Click here(Click here)

Hide 7.INSPECT REAR AXLE HUB BEARING LOOSENESS

Z101186

Click here(Click here)

Hide 8.INSPECT REAR AXLE HUB RUNOUT

Z101186

Click here(Click here)

Hide 42312B 9. STAKE REAR AXLE SHAFT NUT

a.
C444366N01
0.385,0.031 0.667,0.385 0.281,0.354 18 false i

i.

Using a chisel and hammer, stake the rear axle shaft nut.



Hide 89544E 10.INSTALL REAR SKID CONTROL SENSOR

Z101186

Click here(Click here)

Hide 42431 11.INSTALL REAR DISC

Z101186

Click here(Click here)

Hide 12.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

Z101186

Click here(Click here)

Hide 46310B 13.INSTALL PARKING BRAKE ACTUATOR ASSEMBLY

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for TMC Made)

Hide 16. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (for TMC Made)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART