Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge) › from 2021.07
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438027 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C463074N01
5.25,0.417 6.583,1.5 1.333,1.083 2.302,1.104 2.979,1.271 0.677,0.167 1.74,1.438 2.417,1.604 0.677,0.167 0.104,1.552 0.781,1.719 0.677,0.167 0.615,5.333 1.292,5.5 0.677,0.167 3.917,0.417 5.25,1.5 1.333,1.083 4.677,0.688 4.344,0.688 false 6.073,1.25 5.74,1.25 false 6.281,1.74 5.948,1.74 false 3.885,1.792 3.552,1.792 false 2.708,2.135 2.375,2.135 false 1.156,2.208 0.823,2.208 false 1.49,4.573 1.156,4.573 false 3.375,1.177 2.979,1.177 false 2.823,1.521 2.427,1.521 false 1.177,1.635 0.781,1.635 false 0.958,5.323 0.958,5.031 false 6.042,0.698 5.708,0.698 false 4.719,1.25 4.385,1.25 false 6.688,1.615 6.969,1.969 0.281,0.354 18 false 1 6.323,0.563 6.604,0.917 0.281,0.354 18 false 2 4.969,0.563 5.25,0.917 0.281,0.354 18 false 2 3.938,1.635 4.219,1.99 0.281,0.354 18 false 4 2.198,1.99 2.479,2.344 0.281,0.354 18 false 4 0.646,2.073 0.927,2.427 0.281,0.354 18 false 3 0.979,4.417 1.26,4.771 0.281,0.354 18 false 4 6.125,1.156 6.406,1.51 0.281,0.354 10 false ● 1.302,1.615 1.583,1.969 0.281,0.354 10 false x2 4,0.5 4.25,0.75 0.25,0.25 12 false *A 5.333,0.5 5.583,0.75 0.25,0.25 12 false *B 2.375,1.104 3.083,1.406 0.708,0.302 8 false 10 (102, 7) 1.802,1.438 2.51,1.74 0.708,0.302 8 false 10 (102, 7) 0.167,1.552 0.875,1.854 0.708,0.302 8 false 12 (122, 9) 0.667,5.333 1.375,5.635 0.708,0.302 8 false 10 (102, 7) 4.771,1.156 5.052,1.51 0.281,0.354 10 false ● 6.563,1.656 6.844,2.01 0.281,0.354 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 BREATHER PLUG 35141F (Click here) - -
2 TRANSMISSION CASE PLUG ASSEMBLY 35150B (Click here) - -
3 NO. 1 TRANSMISSION CONTROL CABLE BRACKET 33823 - - -
4 WIRE HARNESS CLAMP BRACKET - - - -

*A for Type A *B for Type B
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Toyota Genuine CVT Fluid FE - -

C462294N01
4.563,0.844 5.313,1.01 0.75,0.167 5.708,4.854 6.458,5.021 0.75,0.167 5.167,4.552 5.917,4.719 0.75,0.167 1.417,5.552 2.167,5.719 0.75,0.167 1.375,5.51 2.208,5.76 0.833,0.25 0.073,4.719 0.99,4.885 0.917,0.167 0.031,4.677 1.031,4.927 1,0.25 0.865,2.719 1.615,2.885 0.75,0.167 3.281,0.365 3.802,0.365 false 4.021,1.125 4.385,0.927 4.385,0.927 4.552,0.927 false 4.219,2.635 4.354,2.323 4.354,2.323 4.521,2.323 false 6.167,3.031 6.49,3.031 false 6.083,4.563 6.083,4.844 false 4.99,4.438 5,4.625 5,4.625 5.167,4.625 false 5.188,5.104 5.302,5.406 5.302,5.406 5.469,5.406 false 2.469,5.115 1.948,5.344 1.948,5.344 1.781,5.344 false 0.99,4.802 1.26,4.802 false 1.615,2.792 1.938,2.792 false 3.073,3.052 3.24,3.052 3.24,3.052 3.365,2.677 false 2.167,5.635 2.49,5.635 false 5.833,0.802 6.25,1.167 0.417,0.365 18 false 10 4.167,0.24 4.448,0.594 0.281,0.354 18 false 9 5.698,0.844 5.979,1.198 0.281,0.354 10 false ★ 4.99,2.188 5.406,2.552 0.417,0.365 18 false 7 6.521,2.927 6.802,3.281 0.281,0.354 10 false *1 2.865,2.927 3.281,3.292 0.417,0.365 18 false 8 1.583,5.208 2,5.573 0.417,0.365 18 false 5 5.521,5.271 5.844,5.573 0.323,0.302 18 false 6 1.917,2.865 2.333,3.229 0.417,0.365 10 false x5 0.948,2.729 1.677,2.958 0.729,0.229 8 false 46 (469, 34) 4.635,0.844 5.365,1.073 0.729,0.229 8 false 28 (286, 21) 4.146,1.083 4.427,1.438 0.281,0.354 10 false *a 5.792,4.854 6.521,5.083 0.729,0.229 8 false 46 (469, 34) 5.25,4.563 5.979,4.792 0.729,0.229 8 false 25 (255, 18) 1.49,5.563 2.219,5.792 0.729,0.229 8 false 44 (449, 32) 2.604,5.531 2.927,5.74 0.323,0.208 10 false x3 0.125,4.729 1.052,5.01 0.927,0.281 8 false 170 (1734, 125) 4.865,2.24 5.146,2.594 0.281,0.354 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

5 NO. 2 ENGINE MOVING CONTROL ROD 12364B (Click here) - -
6 FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY 51201 - - -
7 CVT OIL PUMP TYPE T OIL SEAL 30400E (Click here) - -
8 TORQUE CONVERTER ASSEMBLY 32000A (Click here) - -
9 ENGINE ASSEMBLY - (Click here) - -
10 DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT - (Click here) - -

*a Black Color: x1
Silver Color: x5
- -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part
V100135

MP grease
V100136

Clutch spline grease
V100137

Adhesive 1324
★ Precoated part - -

C463076N01
1.5,0.385 2.167,0.552 0.667,0.167 0.042,1.979 0.875,2.229 0.833,0.25 0.083,2.021 0.833,2.188 0.75,0.167 5.833,5.208 6.646,5.375 0.813,0.167 2.792,1.01 3.135,1.01 false 5.5,1.313 5.844,1.313 false 5.927,4.573 6.281,4.573 false 4.281,5.125 4.281,5.469 false 6.24,4.948 6.24,5.198 false 2.167,0.458 2.333,0.458 2.333,0.458 2.635,0.698 false 0.833,2.094 1,2.094 1,2.094 1.094,2.354 false 1.885,5.094 1.563,5.094 false 1.229,4.615 0.906,4.615 false 1.583,3.938 1.26,3.938 false 1.333,2.823 1.01,2.823 false 6.5,4.083 6.177,4.083 false 6.521,3.927 6.906,4.219 0.385,0.292 18 false 11 6.583,4.427 6.969,4.719 0.385,0.292 18 false 15 5.885,1.177 6.271,1.469 0.385,0.292 18 false 17 3.406,0.885 3.792,1.177 0.385,0.292 18 false 16 0.708,2.667 1.094,2.958 0.385,0.292 18 false 17 0.948,3.792 1.333,4.083 0.385,0.292 18 false 13 1.24,4.979 1.625,5.271 0.385,0.292 18 false 14 1.26,4.469 1.646,4.76 0.385,0.292 18 false 12 6.313,4.813 6.635,5.073 0.323,0.26 10 false x2 0.729,3.104 1.052,3.365 0.323,0.26 10 false x2 6.323,1.49 6.646,1.75 0.323,0.26 10 false x2 4.125,5.49 4.51,5.781 0.385,0.292 18 false 18 5.917,5.219 6.813,5.427 0.896,0.208 8 false 12.5 (127, 9) 0.146,2.021 1.042,2.229 0.896,0.208 8 false 20 (204, 15) 1.552,0.385 2.448,0.594 0.896,0.208 8 false 10 (102, 7)

Procedure Part Name Code
Z101186

Z101188

Z101187

11 FLYWHEEL HOUSING UNDER COVER 11361J - - -
12 STARTER ASSEMBLY 28100 - - -
13 NO. 3 WATER BY-PASS HOSE ASSEMBLY 16290F (Click here) - -
14 NO. 4 WATER BY-PASS HOSE 16281N (Click here) - -
15 TCM 89535B (Click here) - -
16 ENGINE WIRE 82121 (Click here) - -
17 ENGINE HANGERS - - - -
18 ENGINE ASSEMBLY WITH TRANSAXLE - - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque

C463077N01
0.833,0.417 1.594,0.583 0.76,0.167 2.063,1.594 2.823,1.76 0.76,0.167 1.594,0.5 1.76,0.5 1.76,0.5 2.031,0.729 false 2.458,1.583 2.458,1.281 false 1.792,1.094 2.125,1.094 false 6.385,0.271 6.719,0.271 false 1.469,0.969 2.021,1.323 0.552,0.354 18 false 19 6.094,0.135 6.646,0.49 0.552,0.354 18 false 20 0.896,0.417 1.594,0.625 0.698,0.208 8 false 43 (438, 32) 2.135,1.604 2.833,1.813 0.698,0.208 8 false 43 (438, 32)

Procedure Part Name Code
Z101186

Z101188

Z101187

19 MANIFOLD STAY 17118 (Click here) - -
20 RESET MEMORY - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 35141F 1.INSTALL NO. 1 BREATHER PLUG

Z101186

HINT:

Perform this procedure only when replacement of the No. 1 breather plug.



a.
C462339N01
0.385,0.052 0.667,0.406 0.281,0.354 18 false i

i.

Coat the O-ring of a new No. 1 breather plug with Toyota Genuine CVT fluid FE and install it to the continuously variable transaxle assembly.

NOTICE:

Be careful not to damage the O-ring.




Hide 35150B 2.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.
C462338C01
0.365,0.052 0.844,0.385 0.479,0.333 18 false i, ii 0.75,0.083 1.125,0.323 0.375,0.24 12 false *A 4.333,0.083 4.708,0.323 0.375,0.24 12 false *B
*A for Type A *B for Type B


i.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission case plug assembly.

NOTICE:

Ensure that the O-ring is not twisted.



ii.

Install the transmission case plug assembly to the continuously variable transaxle assembly.

NOTICE:

Be careful not to damage the O-ring.




Hide 33823 3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Hide 12364B 5.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.
C449797C01
1.896,0.031 2.177,0.385 0.281,0.354 18 false i 2.281,1.01 2.854,1.25 0.573,0.24 10 false 1 (*a), 4 2.688,0.74 3.26,0.979 0.573,0.24 10 false 3 3.802,1.01 3.979,1.219 0.177,0.208 10 true 2
*a Temporarily Tighten - -


i.

Install the No. 2 engine moving control rod to the continuously variable transaxle assembly with the 3 bolts in the order shown in the illustration.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)



Hide 51201 6.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Torque:
170 N*m (1734 kgf*cm, 125 ft.*lbf)

Hide 30400E 7.INSTALL CVT OIL PUMP TYPE T OIL SEAL

a.
C429312C02
2.385,2.583 2.802,2.583 false 6,3.021 6,3.354 false 1.75,3.302 2.417,3.635 2.417,3.635 2.333,3.302 false 5.906,3.375 6.365,3.573 0.458,0.198 10 false SST 2.854,2.521 3.313,2.719 0.458,0.198 10 false SST 4.906,3.313 5.083,3.479 0.177,0.167 10 true *b 0.958,0.271 1.094,0.573 0.135,0.302 18 false i 4.031,0.271 4.25,0.604 0.219,0.333 18 false ii 4.063,2.042 4.281,2.375 0.219,0.333 18 false iv 1,2.042 1.219,2.375 0.219,0.333 18 false iii 2.448,3.604 2.76,3.76 0.313,0.156 10 false *a
*a Clean *b Depth
V100145

MP Grease - -


i.

Ensure that there is no dirt or foreign matter on your hands and then apply MP grease to the entire periphery of the lip of a new CVT oil pump type T oil seal.


ii.

Temporarily install the CVT oil pump type T oil seal by pressing it to the installation surface of the oil pump housing by hand.

NOTICE:

Be sure to install the CVT oil pump type T oil seal in the correct direction.



iii.

Clean the CVT oil pump type T oil seal contact surface of SST and the area around it.

SST
09223-00010  


iv.

Using SST and a hammer, drive the CVT oil pump type T oil seal in evenly, until it is even with the side surface of the transaxle housing.

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Drive the CVT oil pump type T oil seal in gradually, while visually checking that it is even.

·

After installation, confirm that the CVT oil pump type T oil seal has been driven in until it is even with the side surface of the transaxle housing.

·

Wipe any extra grease off with your hand.





Hide 32000A 8.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C446895C03
1.625,0.417 1.906,0.146 true 2.771,0.792 2.521,0.625 true 5.021,0.219 5.313,0.5 false 5.49,1.656 5.302,1.458 false 1.604,2.781 1.208,2.615 1.208,2.615 1.594,2.573 true 2.521,3.292 2.073,3.781 2.073,3.781 2.51,3.083 true 5.156,2.573 5.438,2.302 true 4.833,3.802 5.115,3.531 true 6.042,3.323 5.594,3.813 5.594,3.813 6.042,3.094 true 3.25,4.573 2.854,4.406 2.854,4.406 3.26,4.385 true 4.146,5.115 3.635,5.594 3.635,5.594 4.156,4.896 true 1.958,3.813 2.167,4 0.208,0.188 10 true *1 1.948,0.063 2.26,0.219 0.313,0.156 10 false *a 2.344,0.552 2.531,0.719 0.188,0.167 10 true *b 4.833,0.125 5.146,0.281 0.313,0.156 10 false *c 5.552,1.594 5.74,1.76 0.188,0.167 10 true *a 0.958,2.542 1.146,2.708 0.188,0.167 10 true *a 5.458,2.24 5.646,2.406 0.188,0.167 10 true *a 4.635,3.76 4.823,3.927 0.188,0.167 10 true *a 5.469,3.854 5.677,4.042 0.208,0.188 10 true *1 2.646,4.333 2.833,4.5 0.188,0.167 10 true *a 3.563,5.625 3.771,5.771 0.208,0.146 10 true *1 0.458,0.052 0.74,0.406 0.281,0.354 18 false i 4.219,0.115 4.5,0.469 0.281,0.354 18 false ii 0.479,2.115 0.76,2.469 0.281,0.354 18 false iii 3.979,2.104 4.26,2.458 0.281,0.354 18 false iv 2,4.115 2.281,4.469 0.281,0.354 18 false v
*1 CVT Oil Pump Type T Oil Seal - -
*a Matchmark *b Key
*c Groove - -


i.

Set the key at the top of the drive sprocket and put a matchmark on the transaxle housing.


ii.

Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.

HINT:

The relative positions of the groove (*c) in the sleeve and the setblock will not necessarily be the same as in the illustration.



iii.

Align the matchmark on the housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT oil pump type T oil seal.




iv.

Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT oil pump type T oil seal.




v.

Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the housing and insert the groove of the torque converter assembly into the key of the drive sprocket.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the CVT oil pump type T oil seal.





b.
C430067N02
0.5,0.146 0.781,0.5 0.281,0.354 18 false i

i.

Clean the drive plate and torque converter assembly setting bolt holes.



c.
C446896C03
6.5,0.26 6.688,0.448 false 6.344,1.188 6.063,1.375 false 5.146,0.333 4.927,0.573 true 4.635,1.635 4.135,1.74 true 6.344,0.156 6.656,0.313 0.313,0.156 10 false *a 5.917,1.302 6.229,1.458 0.313,0.156 10 false *b 6.563,1.417 6.875,1.573 0.313,0.156 10 false B 5.188,0.24 5.5,0.396 0.313,0.156 10 false *a 3.906,1.688 4.219,1.844 0.313,0.156 10 false *b 1.281,0.073 1.594,0.229 0.313,0.156 10 false A 0.427,0.083 0.708,0.438 0.281,0.354 18 false i 3.969,0.094 4.25,0.448 0.281,0.354 18 false ii
*a Engine Assembly Surface *b Drive Plate Surface


i.

Using a vernier caliper and straightedge, measure the dimension (A) between the set block and the end face of the continuously variable transaxle assembly.

NOTICE:

Make sure to deduct the thickness of the straightedge.



ii.

Using a vernier caliper and straightedge, measure the dimension (B) between the continuously variable transaxle assembly contact surface of the engine*a and the torque converter assembly contact surfaces of the drive plate*b, and check that dimension (B) is larger than dimension (A).

Standard:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.





Hide 9.INSTALL ENGINE ASSEMBLY

a.
C430124C05
1.833,0.75 2.333,0.417 true 5.438,0.75 5.938,0.417 true 0.729,0.063 1.042,0.219 0.313,0.156 12 false *A 4.188,0.083 4.5,0.24 0.313,0.156 12 false *B 1.354,0.844 1.667,1 0.313,0.156 10 false *1 2.365,0.333 2.677,0.49 0.313,0.156 10 false *2 5.969,0.344 6.281,0.5 0.313,0.156 10 false *2 4.917,0.854 5.229,1.01 0.313,0.156 10 false *1 0.438,0.063 0.719,0.417 0.281,0.354 18 false i
*A for Type A *B for Type B
*1 Crankshaft *2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease - -


i.

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum Grease Amount:

Approximately 1 g (0.0353 oz.)




b.
C430126C04
2.333,0.5 2.667,1.083 2.667,1.083 1.5,0.667 true 2.698,1.021 3.01,1.177 0.313,0.156 10 false *1 5.979,0.01 6.292,0.167 0.313,0.156 10 false A 6.333,1.333 6.594,1.479 0.26,0.146 10 false C 6.052,1.594 6.365,1.75 0.313,0.156 10 false B 5.167,1.604 5.427,1.75 0.26,0.146 10 false C 4.917,1.333 5.083,1.51 0.167,0.177 10 true C 4.688,0.688 4.865,0.854 0.177,0.167 10 true C 4.917,0.156 5.146,0.302 0.229,0.146 10 true C 0.49,0.073 0.771,0.427 0.281,0.354 18 false i 4.094,0.063 4.375,0.417 0.281,0.354 18 false ii
*1 Knock Pin - -


i.

Confirm that the 2 knock pins are installed to the engine assembly and are not damaged.


ii.

Install the engine assembly to the continuously variable transaxle assembly with the 7 bolts.

Torque:
for Bolt A and C : 46 N*m (469 kgf*cm, 34 ft.*lbf)
for Bolt B : 25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excess force when installing the continuously variable transaxle assembly.

·

When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and the continuously variable transaxle assembly are in close contact with one another.



HINT:
·

Bolt (A), (B): Install from the continuously variable transaxle assembly side.

·

Bolt (C): Install from the engine assembly side.





Hide 10.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C431644N01
0.417,0.104 0.875,0.448 0.458,0.344 18 false i 3.771,0.083 4.052,0.438 0.281,0.354 18 false ii

i.

Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



ii.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.




Hide 11361J 11.INSTALL FLYWHEEL HOUSING UNDER COVER

Hide 16290F 13.CONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

Z101186

Click here(Click here)

Hide 16281N 14.CONNECT NO. 4 WATER BY-PASS HOSE

Z101186

Click here(Click here)

Hide 89535B 15.INSTALL TCM

Z101186

NOTICE:

To prevent coolant from entering the TCM through its connector portion, be sure to connect all of the coolant system hoses before installing the TCM.



Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

Hide 82121 16.CONNECT ENGINE WIRE

a.
C462297N02
1.99,2.813 2.271,3.167 0.281,0.354 18 false i 3.417,0.177 4.021,0.552 0.604,0.375 18 false ii, iii 0.271,0.177 0.552,0.531 0.281,0.354 18 false iv

i.

Engage the 3 clamps to install the engine wire.


ii.

Engage the 3 clamps to install the engine wire.


iii.

Connect the engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


iv.

Install the No. 3 water by-pass hose assembly.



b.
C428823C07
0.49,0.135 1.021,0.698 0.531,0.563 18 false i, ii, iii, iv
V113147

Rotate in this Direction - -


i.

Engage the 4 clamps to install the engine wire.


ii.

Install the engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 89 in.*lbf)


iii.

Connect the 6 connectors.


iv.

Connect the 2 connectors, rotate the 2 lock levers and engage the 2 claws.

HINT:

Rotate the lock lever until the claw of the connector makes a click sound.




Hide 17.REMOVE ENGINE HANGERS

Hide 18.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 17118 19.INSTALL MANIFOLD STAY

Z101186

Click here(Click here)