| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 8 | CENTER NO. 4 ENGINE UNDER COVER | 51447D | - | - | - |
| 9 | NO. 1 CENTER FLOOR BRACE | 57543C | - | - | - |
| 10 | FRONT EXHAUST PIPE ASSEMBLY | 17410 | ( )
|
- | - |
| *A | for 2WD | *B | for AWD |
| *C | for TMMF Made | *D | for TMC Made |
| ● | Non-reusable part | - | - |
| *A | for 2WD | *B | for AWD |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
| *a | Cord | - | - |
When removing and storing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using a cord or similar.
Depending on the arrangement of the inlet hose during storage, the inlet hose and rear suspension may interfere and cause fuel leakage.
2.DRAIN FUEL
3.REMOVE WHEEL ASSEMBLY
52592
4.REMOVE REAR BUMPER SIDE SEAL LH
65638
5.SEPARATE REAR WHEEL HOUSE LINER LH
77020A
6.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
77310A
7.REMOVE FUEL TANK CAP ASSEMBLY
51447D
8.REMOVE CENTER NO. 4 ENGINE UNDER COVER
57543C
9.REMOVE NO. 1 CENTER FLOOR BRACE (for TMMF Made)
58415Q
11.REMOVE NO. 1 REAR FLOOR BOARD (for 2WD)
77606
12.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
77027B
13.DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY
Disconnect the No. 1 fuel emission tube sub-assembly from the fuel tank filler pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
77209F
14.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disconnect the fuel tank main tube sub-assembly from the fuel tank filler pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
77730C
15.DISCONNECT NO. 2 CHARCOAL CANISTER ASSEMBLY
for 2WD:
Disconnect the canister air tube from the No. 2 canister.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
Disengage the clamp to separate the No. 1 canister outlet hose sub-assembly from the fuel tank assembly.
for AWD:
Disconnect the canister air tube from the No. 2 canister.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
16.DISCONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY
for 2WD:
Remove the bolt.
Disengage the locations shown in the illustration, and disengage the fuel tank filler pipe sub-assembly from the vehicle body.
for AWD:
Remove the bolt.
Disengage the clamp.
Disengage the locations shown in the illustration, and disengage the fuel tank filler pipe sub-assembly from the vehicle body.
Shift the fuel tank filler pipe sub-assembly.
Disengage the clamp.
77100U
17.REMOVE FUEL TANK ASSEMBLY
|
|
Support the fuel tank assembly using an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
Remove the 4 bolts.
Lower the engine lifter to remove the fuel tank assembly.
77209F
18.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
77027B
19.REMOVE NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY
77217C
20.REMOVE NO. 2 FUEL TANK FILLER PIPE SUPPORT
77216A
21.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT
77218A
22.REMOVE NO. 3 FUEL TANK FILLER PIPE SUPPORT
| *A | for 2WD | *B | for AWD |
77277R
23.REMOVE FUEL TANK FILLER PIPE PROTECTOR
| *A | for 2WD | *B | for AWD |