Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483473 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  C050C23  Left Rear Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTC C050C12.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>C050C12

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C050C23 Left Rear Wheel Speed Sensor Signal Stuck Low
·

When the vehicle is driven from 0 km/h to 12 km/h (0 mph to 7 mph), the wheel speed is 1.8 km/h (1.1 mph) or less for 0.6 seconds or more.

·

When the wheel speed has not exceeded 1.8 km/h (1.1 mph), the vehicle speed reaches 18 km/h (11 mph).

·

When the vehicle speed and wheel speed are both 43.2 km/h (26.8 mph) or more, the pulse signal is not detected for 0.08 seconds or more.


·

Rear speed sensor LH (rear axle hub and bearing assembly LH)*1

·

Rear speed sensor LH*2

·

Speed sensor installation*2


Brake/EPB A

*1: for 2WD

*2: for AWD


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>TEST MODE PROCEDURE

·

DTC precaution

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>PRECAUTION

Procedure to clear warning lights (When not clearing DTCs)
Procedure
1.

Repair or replacement.

2.

Turn the ignition switch to ON.

3.

Drive the vehicle at 2 km/h (1 mph) or more to clear the warning lights.





PROCEDURE

1.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
for 2WD A
for AWD B



A

2.CHECK FREEZE FRAME DATA (WHEEL SPEED)

B

4.CHECK FREEZE FRAME DATA (WHEEL SPEED)
2.CHECK FREEZE FRAME DATA (WHEEL SPEED)
a.

Read the freeze frame data of DTC C050C23.

Chassis > Brake/EPB
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > DTC(C050C23) > Freeze Frame Data
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50040 435 13,14,15,16 C050C23

Result:
Result Proceed to
The value of RL Wheel Speed is 2 km/h or less, and the value of all FL Wheel Speed, FR Wheel Speed, RR Wheel Speed is 12 km/h or more A
The value of RL Wheel Speed is 2 km/h or less, and the value of all FL Wheel Speed, FR Wheel Speed, RR Wheel Speed is 43 km/h or more B


HINT:
·

2 km/h = 1 mph

·

12 km/h = 7 mph

·

43 km/h = 27 mph




A

3.READ VALUE USING GTS (RL WHEEL SPEED)

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

3.READ VALUE USING GTS (RL WHEEL SPEED)

Pre-procedure1

a.

Turn the ignition switch to ON (READY) and perform a road test.


Procedure1

a.

Check that the value of RL Wheel Speed changes in accordance with vehicle speed when accelerating from 0 km/h to 20 km/h (0 mph to 12 mph).

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RL Wheel Speed
50003 435 16
OK:

The value of RL Wheel Speed changes in accordance with vehicle speed.


HINT:

If the result of the road test is within the specified range, it is possible that this DTC was stored due to a particular situation such as brake drag, wheelspin or wheel lockup.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

4.CHECK FREEZE FRAME DATA (WHEEL SPEED)
a.

Read the freeze frame data of DTC C050C23.

Chassis > Brake/EPB
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > DTC(C050C23) > Freeze Frame Data
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50040 435 13,14,15,16 C050C23

Result:
Result Proceed to
The value of RL Wheel Speed is 2 km/h or less, and the value of all FL Wheel Speed, FR Wheel Speed, RR Wheel Speed is 12 km/h or more A
The value of RL Wheel Speed is 2 km/h or less, and the value of all FL Wheel Speed, FR Wheel Speed, RR Wheel Speed is 43 km/h or more B


HINT:
·

2 km/h = 1 mph

·

12 km/h = 7 mph

·

43 km/h = 27 mph




A

5.READ VALUE USING GTS (RL WHEEL SPEED)

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

5.READ VALUE USING GTS (RL WHEEL SPEED)

Pre-procedure1

a.

Turn the ignition switch to ON (READY) and perform a road test.


Procedure1

a.

Check that the value of RL Wheel Speed changes in accordance with vehicle speed when accelerating from 0 km/h to 20 km/h (0 mph to 12 mph).

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RL Wheel Speed
50003 435 16
OK:

The value of RL Wheel Speed changes in accordance with vehicle speed.


HINT:

If the result of the road test is within the specified range, it is possible that this DTC was stored due to a particular situation such as brake drag, wheelspin or wheel lockup.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

6.CHECK REAR SPEED SENSOR INSTALLATION
6.CHECK REAR SPEED SENSOR INSTALLATION
a.
C168336C58
0.917,1.49 1.24,1.74 false 1.031,0.833 1.302,0.448 false 0.75,1.823 1.073,1.99 0.323,0.167 10 false *a 0.135,0.135 0.448,0.333 0.313,0.198 10 false *1 1.281,1.698 1.615,1.906 0.333,0.208 10 false *d 2.438,1.865 2.75,2.063 0.313,0.198 10 false *b 1.344,0.323 1.677,0.531 0.333,0.208 10 false *c
*1 Front Speed Sensor LH
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Check the rear speed sensor LH installation.

OK:

There is no clearance between the rear speed sensor LH and the rear axle carrier LH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

NG