Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483473 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  C050C49  Left Rear Wheel Speed Sensor Internal Electronic Failure  


DESCRIPTION

When the system is starting up and the skid control ECU (brake actuator assembly) detects a speed sensor circuit malfunction via the speed sensor circuit self-diagnosis function, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C050C49 Left Rear Wheel Speed Sensor Internal Electronic Failure A circuit malfunction in the speed sensor is detected during the self test.
·

Rear speed sensor LH (rear axle hub and bearing assembly LH)*1

·

Rear speed sensor LH*2

·

Wire harness or connector

·

Skid control sensor wire LH (No. 2 parking brake wire assembly)

·

Skid control ECU (brake actuator assembly)


Brake/EPB A

*1: for 2WD

*2: for AWD


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
for 2WD A
for AWD B



A

2.CHECK HARNESS AND CONNECTOR (SENSOR CIRCUIT)

B

13.CHECK HARNESS AND CONNECTOR (SENSOR CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SENSOR CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the u6 rear speed sensor LH (rear axle hub and bearing assembly LH) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(u6)Location & Routing

Click Connector(u6)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor LH

u6-2 (RL+) - u6-1 (RL-) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

NG

8.CHECK HARNESS AND CONNECTOR (SENSOR CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the u6 rear speed sensor LH (rear axle hub and bearing assembly LH) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(u6)Location & Routing

Click Connector(u6)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor LH

u6-2 (RL+) - Body ground Ignition switch off Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)
4.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Procedure1

a.
C434671C02
0.469,0.25 0.885,0.5 0.417,0.25 2.479,0.125 2.896,0.375 0.417,0.25 0.573,1.74 0.573,1.167 true 3.042,1.76 2.948,1.25 true 0.083,0.083 0.417,0.333 0.333,0.25 10 false *a 0.948,0.292 1.281,0.542 0.333,0.25 10 false *b 2.979,0.167 3.146,0.583 0.167,0.417 10 false *c 0.583,0.281 0.917,0.531 0.333,0.25 10 false u6 2.552,0.167 2.885,0.417 0.333,0.25 10 false uO2 0.5,1.781 0.833,2.031 0.333,0.25 10 false RL- 3,1.792 3.323,2.104 0.323,0.313 10 false RL-
*a Front view of Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the u6 rear speed sensor LH (rear axle hub and bearing assembly LH) connector.


b.

Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(u6,uO2)Location & Routing

Click Connector(u6)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor LH

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

u6-1 (RL-) or uO2-4 (RL-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2,A39)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

uO2-4 (RL-) or A39-23 (RL-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.
C434670C06
1.5,0.167 1.917,0.417 0.417,0.25 1.865,1.333 2.188,1.656 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.563,0.198 1.979,0.448 0.417,0.25 10 false uO2 2.219,1.667 2.583,1.885 0.365,0.219 10 false RL+
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-3 (RL+) - Body ground Ignition switch off Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.
C434670C06
1.5,0.167 1.917,0.417 0.417,0.25 1.865,1.333 2.188,1.656 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.563,0.198 1.979,0.448 0.417,0.25 10 false uO2 2.219,1.667 2.583,1.885 0.365,0.219 10 false RL+
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-3 (RL+) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SENSOR CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.
C434670C07
1.51,0.167 1.927,0.417 0.417,0.25 1.219,1.635 1.573,1.354 true 2.198,1.656 1.865,1.344 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.563,0.198 1.979,0.448 0.417,0.25 10 false uO2 0.948,1.604 1.313,1.823 0.365,0.219 10 false RL- 2.24,1.646 2.604,1.865 0.365,0.219 10 false RL+
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-3 (RL+) - uO2-4 (RL-) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)
9.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.
C434670C06
1.5,0.167 1.917,0.417 0.417,0.25 1.865,1.333 2.188,1.656 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.563,0.198 1.979,0.448 0.417,0.25 10 false uO2 2.219,1.667 2.583,1.885 0.365,0.219 10 false RL+
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-3 (RL+) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

10.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

12.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.
C434670C02
1.51,0.167 1.927,0.417 0.417,0.25 1.219,1.625 1.573,1.344 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.563,0.198 1.979,0.448 0.417,0.25 10 false uO2 0.958,1.573 1.323,1.792 0.365,0.219 10 false RL-
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-4 (RL-) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

11.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2,A39)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

uO2-4 (RL-) - A39-23 (RL-) Always Below 1 Ω
uO2-3 (RL+) or A39-39 (RL+) - uO2-4 (RL-) or A39-23 (RL-) Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2,A39)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

uO2-3 (RL+) - A39-39 (RL+) Always Below 1 Ω
uO2-3 (RL+) or A39-39 (RL+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (SENSOR CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the u6 rear speed sensor LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(u6)Location & Routing

Click Connector(u6)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor LH

u6-2 (RL+) - u6-1 (RL-) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

14.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

NG

19.CHECK HARNESS AND CONNECTOR (SENSOR CIRCUIT)
14.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the u6 rear speed sensor LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(u6)Location & Routing

Click Connector(u6)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor LH

u6-2 (RL+) - Body ground Ignition switch off Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

15.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

17.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)
15.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Procedure1

a.
C434671C02
0.469,0.25 0.885,0.5 0.417,0.25 2.479,0.125 2.896,0.375 0.417,0.25 0.573,1.74 0.573,1.167 true 3.042,1.76 2.948,1.25 true 0.083,0.083 0.417,0.333 0.333,0.25 10 false *a 0.948,0.292 1.281,0.542 0.333,0.25 10 false *b 2.979,0.167 3.146,0.583 0.167,0.417 10 false *c 0.583,0.281 0.917,0.531 0.333,0.25 10 false u6 2.552,0.167 2.885,0.417 0.333,0.25 10 false uO2 0.5,1.781 0.833,2.031 0.333,0.25 10 false RL- 3,1.792 3.323,2.104 0.323,0.313 10 false RL-
*a Front view of Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the u6 rear speed sensor LH connector.


b.

Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(u6,uO2)Location & Routing

Click Connector(u6)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor LH

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

u6-1 (RL-) or uO2-4 (RL-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

16.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

16.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2,A39)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

uO2-4 (RL-) or A39-23 (RL-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.
C434670C06
1.5,0.167 1.917,0.417 0.417,0.25 1.865,1.333 2.188,1.656 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.563,0.198 1.979,0.448 0.417,0.25 10 false uO2 2.219,1.667 2.583,1.885 0.365,0.219 10 false RL+
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-3 (RL+) - Body ground Ignition switch off Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

18.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
18.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.
C434670C06
1.5,0.167 1.917,0.417 0.417,0.25 1.865,1.333 2.188,1.656 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.563,0.198 1.979,0.448 0.417,0.25 10 false uO2 2.219,1.667 2.583,1.885 0.365,0.219 10 false RL+
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-3 (RL+) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (SENSOR CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.
C434670C07
1.51,0.167 1.927,0.417 0.417,0.25 1.219,1.635 1.573,1.354 true 2.198,1.656 1.865,1.344 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.563,0.198 1.979,0.448 0.417,0.25 10 false uO2 0.948,1.604 1.313,1.823 0.365,0.219 10 false RL- 2.24,1.646 2.604,1.865 0.365,0.219 10 false RL+
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-3 (RL+) - uO2-4 (RL-) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

20.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)
20.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.
C434670C06
1.5,0.167 1.917,0.417 0.417,0.25 1.865,1.333 2.188,1.656 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.563,0.198 1.979,0.448 0.417,0.25 10 false uO2 2.219,1.667 2.583,1.885 0.365,0.219 10 false RL+
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-3 (RL+) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

21.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

23.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
21.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.
C434670C02
1.51,0.167 1.927,0.417 0.417,0.25 1.219,1.625 1.573,1.344 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.563,0.198 1.979,0.448 0.417,0.25 10 false uO2 0.958,1.573 1.323,1.792 0.365,0.219 10 false RL-
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly))


Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-4 (RL-) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

22.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2,A39)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

uO2-4 (RL-) - A39-23 (RL-) Always Below 1 Ω
uO2-3 (RL+) or A39-39 (RL+) - uO2-4 (RL-) or A39-23 (RL-) Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the uO2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2,A39)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

uO2-3 (RL+) - A39-39 (RL+) Always Below 1 Ω
uO2-3 (RL+) or A39-39 (RL+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR