The brake pedal stroke sensor sends the brake pedal stroke distance to the skid control ECU inside the brake actuator assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C05621C | Brake Pedal Position Sensor Supply Voltage Circuit Voltage Out of Range | Brake pedal stroke sensor assembly power source malfunction detected. | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
| C139200 | Zero Point Calibration of Stroke Sensor | While the brake pedal is not being depressed, brake pedal stroke sensor assembly zero point not calibrated signal is received. (A correct brake pedal stroke sensor assembly zero point learning value is not present). | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
| P057A11 | Brake Pedal Position Sensor "A" Circuit Short to Ground | Open or short detected due to abnormality in brake pedal stroke sensor assembly output circuit 1. | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
| P057A15 | Brake Pedal Position Sensor "A" Circuit Short to Battery or Open | Open or short detected due to abnormality in brake pedal stroke sensor assembly output circuit 1. | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
| P057A28 | Brake Pedal Position Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure | Difference in change amount of brake pedal stroke sensor assembly output voltage 1 (SKS1) is abnormally large for 0.1 seconds or more. (SKS1 output comparison invalid). | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
| P057A64 | Brake Pedal Position Sensor "A" Signal Plausibility Failure | Difference in change amount of brake pedal stroke sensor assembly output voltage 1 (SKS1) is abnormally large for 0.2 seconds or more. (SKS1 output comparison invalid). | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
| P05DB11 | Brake Pedal Position Sensor "B" Circuit Short to Ground | Open or short detected due to abnormality in brake pedal stroke sensor assembly output circuit 2. | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
| P05DB15 | Brake Pedal Position Sensor "B" Circuit Short to Battery or Open | Open or short detected due to abnormality in brake pedal stroke sensor assembly output circuit 2. | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
| P05DB28 | Brake Pedal Position Sensor "B" Signal Bias Level Out of Range / Zero Adjustment Failure | Difference in change amount of brake pedal stroke sensor assembly output voltage 2 (SKS2) is abnormally large for 0.1 seconds or more. (SKS2 output comparison invalid). | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
| P05DB64 | Brake Pedal Position Sensor "B" Signal Plausibility Failure | Difference in change amount of brake pedal stroke sensor assembly output voltage 2 (SKS2) is abnormally large for 0.2 seconds or more. (SKS2 output comparison invalid). | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
| P05E064 | Brake Pedal Position Sensor "A"/"B" Signal Plausibility Failure | Difference between change amounts of brake pedal stroke sensor assembly output voltage 1 (SKS1) and brake pedal stroke sensor assembly output voltage 2 (SKS2) is abnormally large for 0.2 seconds or more. (SKS1 and SKS2 output comparison invalid). | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
| P157A62 | Brake Pedal Position Sensor "A" / "B" Brake Master Cylinder Pressure Sensor Multiple Sensor Signal Compare Failure | While driving at a vehicle speed of 3 km/h or more, the master cylinder pressure sensor value is too high relative to the brake pedal stroke sensor assembly value for 0.2 seconds or more. | ·
Brake pedal stroke sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration" after performing "Reset Memory".
After replacing the skid control ECU (brake actuator assembly), perform "Calibration" after performing "Reset Memory".
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| for RHD | A |
| for LHD | B |
A
B
Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.
Check and adjust the brake pedal height.
Adjust the brake pedal stroke sensor assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the A31 brake pedal stroke sensor assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A39,A31)Location & Routingewd_type=routing;type=c,c;code=A39,A31 Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A39;pinno=17,6,42,29 Click Connector(A31)Instrument Panel>Engine Room Main Wire>Brake Pedal Stroke Sensor Assemblyewd_type=component;type=c;code=A31;pinno=1,2,4,3 |
||
| A39-17 (VSK) - A31-1 (VSK) | Always | Below 1 Ω |
| A39-17 (VSK) or A31-1 (VSK) - Body ground | Always | 10 kΩ or higher |
| A39-6 (SKS1) - A31-2 (SKS1) | Always | Below 1 Ω |
| A39-6 (SKS1) or A31-2 (SKS1) - Body ground | Always | 10 kΩ or higher |
| A39-42 (SKS2) - A31-4 (SKS2) | Always | Below 1 Ω |
| A39-42 (SKS2) or A31-4 (SKS2) - Body ground | Always | 10 kΩ or higher |
| A39-29 (SKG) - A31-3 (SKG) | Always | Below 1 Ω |
| A39-29 (SKG) or A31-3 (SKG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the A39 skid control ECU (brake actuator assembly) connector.
OK
NG
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A31)Location & Routingewd_type=routing;type=c;code=A31 Click Connector(A31)Instrument Panel>Engine Room Main Wire>Brake Pedal Stroke Sensor Assemblyewd_type=component;type=c;code=A31;pinno=1,3 |
||
| A31-1 (VSK) - A31-3 (SKG) | Ignition switch ON | 4.84 to 5.16 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model TMMF Made RHD)>REMOVAL
Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.
Check and adjust the brake pedal height.
Adjust the brake pedal stroke sensor assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the A31 brake pedal stroke sensor assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A39,A31)Location & Routingewd_type=routing;type=c,c;code=A39,A31 Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A39;pinno=17,6,42,29 Click Connector(A31)Instrument Panel>Engine Room Main Wire>Brake Pedal Stroke Sensor Assemblyewd_type=component;type=c;code=A31;pinno=1,2,4,3 |
||
| A39-17 (VSK) - A31-1 (VSK) | Always | Below 1 Ω |
| A39-17 (VSK) or A31-1 (VSK) - Body ground | Always | 10 kΩ or higher |
| A39-6 (SKS1) - A31-2 (SKS1) | Always | Below 1 Ω |
| A39-6 (SKS1) or A31-2 (SKS1) - Body ground | Always | 10 kΩ or higher |
| A39-42 (SKS2) - A31-4 (SKS2) | Always | Below 1 Ω |
| A39-42 (SKS2) or A31-4 (SKS2) - Body ground | Always | 10 kΩ or higher |
| A39-29 (SKG) - A31-3 (SKG) | Always | Below 1 Ω |
| A39-29 (SKG) or A31-3 (SKG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the A39 skid control ECU (brake actuator assembly) connector.
OK
NG
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A31)Location & Routingewd_type=routing;type=c;code=A31 Click Connector(A31)Instrument Panel>Engine Room Main Wire>Brake Pedal Stroke Sensor Assemblyewd_type=component;type=c;code=A31;pinno=1,3 |
||
| A31-1 (VSK) - A31-3 (SKG) | Ignition switch ON | 4.84 to 5.16 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for HV Model LHD)>REMOVAL
NG