Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483557 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  P057112  Brake Switch "A" Circuit Short to Battery  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied.

DTCs may be stored if either of the following occurs:

·

Stop light switch assembly stuck on malfunction.

·

The accelerator and brake pedals are depressed simultaneously.*


HINT:

*: The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
P057112 Brake Switch "A" Circuit Short to Battery The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.1 kgf/cm2, 72.5 psi) or less, and the stop light switch assembly is on for 60 seconds or more.
·

Stop light switch assembly

·

Stop light switch assembly installation

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)

·

ECM

·

Shift lock control ECU (shift lock control unit assembly)

·

TCM

·

Certification ECU (smart key ECU assembly)


Brake/EPB A

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY

·

DTC precaution

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>PRECAUTION

Procedure to clear warning lights (When not clearing DTCs)
Procedure
1.

Repair or replacement.

2.

Turn the ignition switch to ON.

3.

Drive the vehicle and depress the brake pedal 2 or 3 times to clear the warning lights.





PROCEDURE

1.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION

B

12.CHECK BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.CHECK BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the brake pedal height and stop light switch assembly installation.

HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Gasoline Model LHD)>ADJUSTMENT


OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT)

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.
C440416C45
0.375,0.75 0.813,1.01 0.438,0.26 2.156,1.656 1.844,1.031 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 2.177,1.688 2.333,1.885 0.156,0.198 10 false L 0.469,0.813 0.958,1.146 0.49,0.333 10 false A63
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Brake pedal released Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

6.CHECK VEHICLE
6.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
w/ Entry and Start System A
w/ o Entry and Start System B



A

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)

B

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H20 shift lock control ECU (shift lock control unit assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H20 shift lock control ECU (shift lock control unit assembly) connector.


e.

Disconnect the D71 TCM connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H20 shift lock control ECU (shift lock control unit assembly) connector.


e.

Disconnect the D71 TCM connector.


f.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE SMART KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H19 shift lock control ECU (shift lock control unit assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H19 shift lock control ECU (shift lock control unit assembly) connector.


e.

Disconnect the D71 TCM connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the brake pedal height and stop light switch assembly installation.

HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Gasoline Model RHD)>ADJUSTMENT


OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT)

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.
C440416C45
0.375,0.75 0.813,1.01 0.438,0.26 2.156,1.656 1.844,1.031 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 2.177,1.688 2.333,1.885 0.156,0.198 10 false L 0.469,0.813 0.958,1.146 0.49,0.333 10 false A63
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Brake pedal released Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

14.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
14.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

15.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
15.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

16.CHECK VEHICLE
16.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
w/ Entry and Start System A
w/ o Entry and Start System B



A

17.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)

B

20.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)
17.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H20 shift lock control ECU (shift lock control unit assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

18.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
18.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H20 shift lock control ECU (shift lock control unit assembly) connector.


e.

Disconnect the D71 TCM connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

19.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY)
19.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H20 shift lock control ECU (shift lock control unit assembly) connector.


e.

Disconnect the D71 TCM connector.


f.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE SMART KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H19 shift lock control ECU (shift lock control unit assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

21.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
21.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H19 shift lock control ECU (shift lock control unit assembly) connector.


e.

Disconnect the D71 TCM connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-3 (L) - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR