Refer to DTCs C05121F.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C14E914 | Right Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open | Any of the following is detected:
·
The speed sensor power source voltage is low for 0.5 seconds or more. ·
The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more. |
·
Rear speed sensor RH*1 ·
Rear speed sensor RH (rear axle hub and bearing assembly RH)*2 ·
Skid control sensor wire RH (No. 1 parking brake wire assembly) ·
Wire harness or connector ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake/EPB | A |
*1: for AWD
*2: for 2WD
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.
Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Speed Open | Rear speed sensor RH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Tester Display |
|---|
| RR Speed Open |
Check for any momentary interruptions in the wire harness and connectors.
Perform the above inspection before removing the sensor and connector.
| Result | Proceed to |
|---|---|
| The value of RR Speed Open is always Normal | A |
| The value of RR Speed Open outputs Error one or more times | B |
A
B
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Wheel Speed | Rear speed sensor RH | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| RR Wheel Speed |
Check the rear speed sensor RH output value.
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C14E914 is not output | A |
| C14E914 is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| for 2WD | A |
| for AWD | B |
A
B
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the u2 and uO1 skid control sensor wire LH (No. 2 parking brake wire assembly) connectors.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(u2,uO1)Location & Routingewd_type=routing;type=c,w;code=u2,uO1 Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO1;pinno=4,3 |
||
| u2-2 (+) - uO1-4 (RR+) | Always | Below 1 Ω |
| u2-2 (+) or uO1-4 (RR+) - Body ground and other terminals | Always | 10 kΩ or higher |
| u2-1 (-) - uO1-3 (RR-) | Always | Below 1 Ω |
| u2-1 (-) or uO1-3 (RR-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Pre-procedure1
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A38,uO1)Location & Routingewd_type=routing;type=c,w;code=A38,uO1 Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assemblyewd_type=component;type=c;code=A38;pinno=7,8 Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO1;pinno=4,3 |
||
| A38-7 (RR+) - uO1-4 (RR+) | Always | Below 1 Ω |
| A38-7 (RR+) or uO1-4 (RR+) - Body ground | Always | 10 kΩ or higher |
| A38-8 (RR-) - uO1-3 (RR-) | Always | Below 1 Ω |
| A38-8 (RR-) or uO1-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Reconnect the uO1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(u2)Location & Routingewd_type=routing;type=c;code=u2 |
||
| u2-2 (+) - Body ground | Ignition switch ON | 8 to 14 V |
Check the rear speed sensor RH signal after replacement.
The rear speed sensor RH and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.
If the rear speed sensor RH and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the u2 and uO1 skid control sensor wire LH (No. 2 parking brake wire assembly) connectors.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(u2,uO1)Location & Routingewd_type=routing;type=c,w;code=u2,uO1 Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO1;pinno=4,3 |
||
| u2-1 (+) - uO1-4 (RR+) | Always | Below 1 Ω |
| u2-1 (+) or uO1-4 (RR+) - Body ground and other terminals | Always | 10 kΩ or higher |
| u2-2 (-) - uO1-3 (RR-) | Always | Below 1 Ω |
| u2-2 (-) or uO1-3 (RR-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Pre-procedure1
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A38,uO1)Location & Routingewd_type=routing;type=c,w;code=A38,uO1 Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assemblyewd_type=component;type=c;code=A38;pinno=7,8 Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO1;pinno=4,3 |
||
| A38-7 (RR+) - uO1-4 (RR+) | Always | Below 1 Ω |
| A38-7 (RR+) or uO1-4 (RR+) - Body ground | Always | 10 kΩ or higher |
| A38-8 (RR-) - uO1-3 (RR-) | Always | Below 1 Ω |
| A38-8 (RR-) or uO1-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Reconnect the uO1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(u2)Location & Routingewd_type=routing;type=c;code=u2 |
||
| u2-1 (+) - Body ground | Ignition switch ON | 8 to 14 V |
Check the rear speed sensor RH signal after replacement.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG