The main body ECU (multiplex network body ECU) detects whether either the rear seat occupied or unoccupied based on the rear occupant detection sensor condition and then sends the rear occupant detection sensor status signal to the combination meter assembly.
The power distribution box assembly detects whether either the rear seat belts are fastened or unfastened based on the rear seat belt buckle switch condition and then sends the rear seat belt buckle switch status signal to the combination meter assembly.
The combination meter assembly illuminates, blinks or turns off the rear seat belt warning light on the combination meter assembly in accordance with the vehicle speed, rear seat belt state and rear seat occupant state.
The seat belt warning system uses the CAN communication system and CXPI communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Seat RH Buckle Switch Status | Rear RH seat belt buckle switch status | Set/Unset/Unknown | Set: Rear RH seat belt fastened
Unset: Rear RH seat belt not fastened |
- |
| Rear Seat Center Buckle Switch Status | Rear center seat belt buckle switch status | Set/Unset/Unknown | Set: Rear center seat belt fastened
Unset: Rear center seat belt not fastened |
- |
| Rear Seat LH Buckle Switch Status | Rear LH seat belt buckle switch status | Set/Unset/Unknown | Set: Rear LH seat belt fastened
Unset: Rear LH seat belt not fastened |
- |
| Tester Display |
|---|
| Rear Seat RH Buckle Switch Status |
| Rear Seat Center Buckle Switch Status |
| Rear Seat LH Buckle Switch Status |
The GTS display changes correctly in response to the rear seat belt buckle switch condition.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Rear RH seat belt malfunction) | B |
| NG (Rear center or rear LH seat belt malfunction) | C |
A
B
C
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RC-Seat Occupant Sensor Switch | Rear occupant detection sensor (for center) | ON or OFF | ON: Rear center seat occupied
OFF: Rear center seat not occupied |
- |
| RL-Seat Occupant Sensor Switch | Rear occupant detection sensor (for LH) | ON or OFF | ON: Rear LH seat occupied
OFF: Rear LH seat not occupied |
- |
| RR-Seat Occupant Sensor Switch | Rear occupant detection sensor (for RH) | ON or OFF | ON: Rear RH seat occupied
OFF: Rear RH seat not occupied |
- |
| Tester Display |
|---|
| RC-Seat Occupant Sensor Switch |
| RL-Seat Occupant Sensor Switch |
| RR-Seat Occupant Sensor Switch |
The GTS display changes correctly in response to the rear seat condition (occupied or unoccupied).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR (for Rear Side)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O61 rear occupant detection sensor (for LH) connector.
Disconnect the O62 rear occupant detection sensor (for RH) connector.
Disconnect the O63 rear occupant detection sensor (for center) connector.
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O61,H4)Location & Routingewd_type=routing;type=c,c;code=O61,H4 Click Connector(O61)Body>Floor Wire>Rear Seat Belt Warning Occupant Detection Sensor LHewd_type=component;type=c;code=O61;pinno=2,1 Click Connector(H4)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H4;pinno=24 |
||
| O61-2 (+) - H4-24 (RLSS) | Always | Below 1 Ω |
| O61-2 (+) or H4-24 (RLSS) - Body ground | Always | 10 kΩ or higher |
| O61-1 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O62,H4)Location & Routingewd_type=routing;type=c,c;code=O62,H4 Click Connector(O62)Body>Floor Wire>Rear Seat Belt Warning Occupant Detection Sensor RHewd_type=component;type=c;code=O62;pinno=2,1 Click Connector(H4)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H4;pinno=25 |
||
| O62-2 (+) - H4-25 (RRSS) | Always | Below 1 Ω |
| O62-2 (+) or H4-25 (RRSS) - Body ground | Always | 10 kΩ or higher |
| O62-1 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O63,H4)Location & Routingewd_type=routing;type=c,c;code=O63,H4 Click Connector(O63)Body>Floor Wire>Rear Seat Belt Warning Occupant Detection Sensor Centerewd_type=component;type=c;code=O63;pinno=2,1 Click Connector(H4)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H4;pinno=23 |
||
| O63-2 (+) - H4-23 (RCSS) | Always | Below 1 Ω |
| O63-2 (+) or H4-23 (RCSS) - Body ground | Always | 10 kΩ or higher |
| O63-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O19 rear seat inner belt assembly RH connector.
Disconnect the 4E power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O19)Location & Routingewd_type=routing;type=c;code=O19 Click Connector(O19)Body>Floor Wire>Rear Seat Inner Belt Assembly RHewd_type=component;type=c;code=O19;pinno=5,4 |
||
| O19-5 (RBR+) - 4E-8 | Always | Below 1 Ω |
| O19-5 (RBR+) or 4E-8 - Body ground | Always | 10 kΩ or higher |
| O19-4 (RBR-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O20 rear seat inner with center belt assembly LH connector.
Disconnect the 4E power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O20)Location & Routingewd_type=routing;type=c;code=O20 Click Connector(O20)Body>Floor Wire>Rear Seat Inner Belt with Center Assembly LHewd_type=component;type=c;code=O20;pinno=3,5,2,4 |
||
| O20-3 (CBR+) - 4E-4 | Always | Below 1 Ω |
| O20-3 (CBR+) or 4E-4 - Body ground | Always | 10 kΩ or higher |
| O20-5 (LBR+) - 4E-19 | Always | Below 1 Ω |
| O20-5 (LBR+) or 4E-19 - Body ground | Always | 10 kΩ or higher |
| O20-2 (CBR-) - Body ground | Always | Below 1 Ω |
| O20-4 (LBR-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG